Give users the option of completely powering off unoccupied
SATA ports using the existing min_power link_power_management_policy
option.  When the use selects this option on an empty port, we
will power the port off by setting DET to off.  For occupied ports,
behavior is unchanged.
Signed-off-by: NKristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Some errors still show up, but the dock works, both drives can be
accessed at the same time

The chip maker and designation is unknown - possibly jmicron JMB350?
Signed-off-by: NPavel Herrmann <morpheus.ibis@gmail.com>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Don't powerdown Compaq Triflex IDE device on suspend

This fixes APM suspend on Compaq Armada 7400.
APM BIOS doesn't suspend if IDE is powered down when suspending.
The Triflex controller is found only on old Compaq boards,
so this patch will hopefully have no side effects.
Signed-off-by: NMikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Previously we used Maximum Unmap LBA Count in the Block Limits VPD to
signal the maximum number of sectors we could handle in a single Write
Same command.

Starting with SBC3r26 the Block Limits VPD has an explicit limit on the
number of blocks in a Write Same. This means we can stop abusing a field
related to the Unmap command and let our SAT use the proper value in the
VPD (Maximum Write Same Length).
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
Cc: stable@kernel.org

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

* New code correctly calculates SMC registers values, adjusts calculated
  to admissible ranges, enlarges cycles when required and converts values
  into SMC's format.
* Support for TDF cycles (ATA t6z) and IORDY line added.
* Eliminate need in the initial_timing structure.
* Code cleanup.
Signed-off-by: NIgor Plyatov <plyatov@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

This is a cosmetic change to prevent libata-sff adding irq
descriptions to dummy ports, since the information, while largely
unused, is erroneous.
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The old IDE cmd64x checks the status of the CNTRL register to see if
the ports are enabled before probing them.  pata_cmd64x doesn't do
this, which causes a HPMC on parisc when it tries to poke at the
secondary port because apparently the BAR isn't wired up (and a
non-responding piece of memory causes a HPMC).

Fix this by porting the CNTRL register port detection logic from IDE
cmd64x.  In addition, following converns from Alan Cox, add a check to
see if a mobility electronics bridge is the immediate parent and forgo
the check if it is (prevents problems on hotplug controllers).
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

ae01b249 (libata: Implement ATA_FLAG_NO_DIPM and apply it to mcp65)
added ATA_FLAG_NO_DIPM and made ata_eh_set_lpm() check the flag.
However, @ap is NULL if @link points to a PMP link and thus the
unconditional @ap->flags dereference leads to the following oops.

  BUG: unable to handle kernel NULL pointer dereference at 0000000000000018
  IP: [<ffffffff813f98e1>] ata_eh_recover+0x9a1/0x1510
  ...
  Pid: 295, comm: scsi_eh_4 Tainted: P            2.6.38.5-core2 #1 System76, Inc. Serval Professional/Serval Professional
  RIP: 0010:[<ffffffff813f98e1>]  [<ffffffff813f98e1>] ata_eh_recover+0x9a1/0x1510
  RSP: 0018:ffff880132defbf0  EFLAGS: 00010246
  RAX: 0000000000000000 RBX: ffff880132f40000 RCX: 0000000000000000
  RDX: ffff88013377c000 RSI: ffff880132f40000 RDI: 0000000000000000
  RBP: ffff880132defce0 R08: ffff88013377dc58 R09: ffff880132defd98
  R10: 0000000000000000 R11: 00000000ffffffff R12: 0000000000000000
  R13: 0000000000000000 R14: ffff88013377c000 R15: 0000000000000000
  FS:  0000000000000000(0000) GS:ffff8800bf700000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
  CR2: 0000000000000018 CR3: 0000000001a03000 CR4: 00000000000406e0
  DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
  DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
  Process scsi_eh_4 (pid: 295, threadinfo ffff880132dee000, task ffff880133b416c0)
  Stack:
   0000000000000000 ffff880132defcc0 0000000000000000 ffff880132f42738
   ffffffff813ee8f0 ffffffff813eefe0 ffff880132defd98 ffff88013377f190
   ffffffffa00b3e30 ffffffff813ef030 0000000032defc60 ffff880100000000
  Call Trace:
   [<ffffffff81400867>] sata_pmp_error_handler+0x607/0xc30
   [<ffffffffa00b273f>] ahci_error_handler+0x1f/0x70 [libahci]
   [<ffffffff813faade>] ata_scsi_error+0x5be/0x900
   [<ffffffff813cf724>] scsi_error_handler+0x124/0x650
   [<ffffffff810834b6>] kthread+0x96/0xa0
   [<ffffffff8100cd64>] kernel_thread_helper+0x4/0x10
  Code: 8b 95 70 ff ff ff b8 00 00 00 00 48 3b 9a 10 2e 00 00 48 0f 44 c2 48 89 85 70 ff ff ff 48 8b 8d 70 ff ff ff f6 83 69 02 00 00 01 <48> 8b 41 18 0f 85 48 01 00 00 48 85 c9 74 12 48 8b 51 08 48 83
  RIP  [<ffffffff813f98e1>] ata_eh_recover+0x9a1/0x1510
   RSP <ffff880132defbf0>
  CR2: 0000000000000018

Fix it by testing @link->ap->flags instead.

stable: ATA_FLAG_NO_DIPM was added during 2.6.39 cycle but was
        backported to 2.6.37 and 38.  This is a fix for that and thus
        also applicable to 2.6.37 and 38.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: N"Nathan A. Mourey II" <nmoureyii@ne.rr.com>
LKML-Reference: <1304555277.2059.2.camel@localhost.localdomain>
Cc: Connor H <cmdkhh@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

At the end of section 10.1 of AHCI spec (rev 1.3), it states

Software shall not set PxCMD.ST to 1 until it is determined that
a functoinal device is present on the port as determined by
PxTFD.STS.BSY=0, PxTFD.STS.DRQ=0 and PxSSTS.DET=3h

Even though most AHCI host controller works without this check,
specific controller will fail under this condition.
Signed-off-by: NJian Peng <jipeng2005@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The "struct ata_timing" must contain 10 members, but ".dmack_hold" member was
forgotten for "initial_timing" initialisation. This patch fixes such a problem.
Signed-off-by: NIgor Plyatov <plyatov@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The AT91SAM9 microcontrollers with master clock higher then 105 MHz
and PIO0, have overflow of the NCS_RD_PULSE value in the MSB. This
lead to "NCS_RD_PULSE" pulse longer then "NRD_CYCLE" pulse and driver
does not detect ATA device.
Signed-off-by: NIgor Plyatov <plyatov@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The previously submitted patch was word-wrapped.

This patch adds the AHCI-mode SATA DeviceIDs for the Intel Panther Point PCH.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The previously submitted patch was word-wrapped.

This patch adds the IDE-mode SATA DeviceIDs for the Intel Panther
Point PCH.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

 Commit 4a5610a0 fixed an issue with
 the Pioneer DVR-212D not handling SETXFER correctly. An openSUSE user
 reported a similar issue with his DVR-216D that the NOSETXFER horkage
 worked around for him as well.

 This patch adds the DVR-216D (1.08) to the horkage list for NOSETXFER.

 The issue was reported at:
 https://bugzilla.novell.com/show_bug.cgi?id=679143Reported-by: NVolodymyr Kyrychenko <vladimir.kirichenko@gmail.com>
Signed-off-by: NJeff Mahoney <jeffm@suse.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The ahci_pmp_attach() & ahci_pmp_detach() unmask port irqs, but they
are also called during port initialization, before ahci host irq
handler is registered. On ce4100 platform, this sometimes triggers
"irq 4: nobody cared" message when loading driver.

Fixed this by not touching the register if the port is in frozen
state, and mark all uninitialized port as frozen.
Signed-off-by: NMaxime Bizon <mbizon@freebox.fr>
Acked-by: NTejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

NVIDIA mcp65 familiy of controllers cause command timeouts when DIPM
is used.  Implement ATA_FLAG_NO_DIPM and apply it.

This problem was reported by Stefan Bader in the following thread.

 http://thread.gmane.org/gmane.linux.ide/48841

stable: applicable to 2.6.37 and 38.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NStefan Bader <stefan.bader@canonical.com>
Cc: stable@kernel.org
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

This patch adds an sysfs attribute 'em_message_supported' to the
ahci host device which prints out the supported enclosure management
message types.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

Scripted with coccinelle.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Use gpio_request_array() / gpio_free_array(), this makes the code
cleaner and less error prone.

This patch also properly frees GPIOs in case ata_host_activate() call fails.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

In FSL sata v2 block, the snoop bit of PRDT Word3 description
information is at bit28 instead of bit22.

This patch adds FSL sata v2 probe and resolve this difference.
Signed-off-by: NLei Xu <B33228@freescale.com>
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

1b4b:91a3 seems to be another PCI ID for marvell ahci.  Add it.
Reported and tested in the following thread.

 http://thread.gmane.org/gmane.linux.kernel/1068354Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NBorislav Petkov <bp@alien8.de>
Reported-by: NAlessandro Tagliapietra <tagliapietra.alessandro@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

RX_WATER_MARK sets the number of locations in Rx FIFO that can be used before
the transport layer instructs the link layer to transmit HOLDS. Note that it
can take some time for the HOLDs to get to the other end, and that in the
interim there must be enough room in the FIFO to absorb all data that could
arrive.

Update the new recommended value to 16.
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

When a single device error is detected, the device under the error
is indicated by the error bit set in the DER. There is a one to one
mapping between register bit and devices on Port multiplier(PMP)
i.e. bit 0 represents PMP device 0 and bit 1 represents PMP device
1 etc.

Current implementation treats Device error register value as device
number not set of bits representing multiple device on PMP. It is
changed to consider bit level.

No need to check for each set bit as all command is going to be
aborted.
Signed-off-by: NAshish Kalra <B00888@freescale.com>
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

As per SAT-3 the WWN ID should be included in the VPD page 0x83
(device identification) emulation.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Some DMA controllers (eg: drivers/dma/dw_dmac*) allow platform specific
configuration for dma transfers. User drivers need to set chan->private field
of channel with pointer to configuration data. This patch takes dma_priv data
from platform data and passes it to chan->private_data, in order to pass
platform specific configuration to DMAC controller.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Commit 40d69ba0
("pata_hpt{37x|3x2n}: use pr_*(DRV_NAME ...) instead of printk(KERN_* ...)")
used pr_<level>.

Add #define pr_fmt and remove DRV_NAME.
Increment driver version numbers.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The Arasan CompactFlash Device Controller has three basic modes of
operation: PC card ATA using I/O mode, PC card ATA using memory mode, PC card
ATA using true IDE modes.

Currently driver supports only True IDE mode.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

This patch adds ata_sff_queue_work() & ata_sff_queue_delayed_work() routine in
libata-sff.c file. This routine can be used by ata drivers to use ata_sff_wq.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

This patch adds an updated SATA RAID DeviceID for the Intel Patsburg PCH.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Recognize Marvell 88SE9125 PCIe SATA 6.0 Gb/s controller.
Signed-off-by: NPer Jessen <per@computer.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Commit 6b7ae954 (libata: reimplement link power
management) removed the check of ATA_FLAG_LPM but neglected to remove the flag
itself.  Do it now...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

All checks of ATA_FLAG_NO_LEGACY have been removed by the commits
c791c306 ([libata] minor PCI IDE probe
fixes and cleanups) and f0d36efd (libata:
update libata core layer to use devres), so I think it's time to finally
get rid of this flag...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Commit 0d5ff566 (libata: convert to iomap)
removed all checks of ATA_FLAG_MMIO but neglected to remove the flag itself.
Do it now, at last...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

These flags are marked as obsolete and the checks for them have been removed
by commit 29444088 (libata-sff: kill unused
ata_bus_reset()), so I think it's time to finally get rid of them...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The driver makes use of the two options (CONFIG_SATA_DWC_[V]DEBUG) to enable
the debug output but they both are absent in drivers/ata/Kconfig...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The driver erroneously uses ata_get_cmd_descript() not only for printing out
the ATA commands but also the protocol and DMA direction enums. Add functions
for properly printing those out...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The caller expects this function to return the DMA channel number on success,
while it returns 0...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>