Skip to content

K
Kernel

openeuler / Kernel
大约 2 年 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 02 7月, 2018 1 次提交
  3. 17 6月, 2018 1 次提交
  5. 11 5月, 2018 1 次提交
  7. 13 4月, 2018 1 次提交
  9. 19 12月, 2017 2 次提交
  11. 02 11月, 2017 1 次提交
    • G
      License cleanup: add SPDX GPL-2.0 license identifier to files with no license · b2441318
      由 Greg Kroah-Hartman 提交于 
      Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: NKate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: NPhilippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      b2441318
  13. 20 10月, 2017 1 次提交
  15. 03 10月, 2017 1 次提交
    • M
      thunderbolt: Add support for XDomain discovery protocol · d1ff7024
      由 Mika Westerberg 提交于 
      When two hosts are connected over a Thunderbolt cable, there is a
protocol they can use to communicate capabilities supported by the host.
The discovery protocol uses automatically configured control channel
(ring 0) and is build on top of request/response transactions using
special XDomain primitives provided by the Thunderbolt base protocol.

The capabilities consists of a root directory block of basic properties
used for identification of the host, and then there can be zero or more
directories each describing a Thunderbolt service and its capabilities.

Once both sides have discovered what is supported the two hosts can
setup high-speed DMA paths and transfer data to the other side using
whatever protocol was agreed based on the properties. The software
protocol used to communicate which DMA paths to enable is service
specific.

This patch adds support for the XDomain discovery protocol to the
Thunderbolt bus. We model each remote host connection as a Linux XDomain
device. For each Thunderbolt service found supported on the XDomain
device, we create Linux Thunderbolt service device which Thunderbolt
service drivers can then bind to based on the protocol identification
information retrieved from the property directory describing the
service.

This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: NMichael Jamet <michael.jamet@intel.com>
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: NYehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      d1ff7024
  17. 28 8月, 2017 1 次提交
  19. 23 5月, 2017 1 次提交
  21. 12 4月, 2017 1 次提交
  23. 07 2月, 2017 1 次提交
  25. 14 12月, 2016 1 次提交
    • I
      s390/zcrypt: add multi domain support · e28d2af4
      由 Ingo Tuchscherer 提交于 
      Currently the ap infrastructure only supports one domain at a time.
This feature extends the generic cryptographic device driver to
support multiple cryptographic domains simultaneously.

There are now card and queue devices on the AP bus with independent
card and queue drivers. The new /sys layout is as follows:

/sys/bus/ap
    devices
        <xx>.<yyyy> -> ../../../devices/ap/card<xx>/<xx>.<yyyy>
        ...
        card<xx> -> ../../../devices/ap/card<xx>
        ...
    drivers
        <drv>card
            card<xx> -> ../../../../devices/ap/card<xx>
        <drv>queue
            <xx>.<yyyy> -> ../../../../devices/ap/card<xx>/<xx>.<yyyy>
            ...

/sys/devices/ap
    card<xx>
        <xx>.<yyyy>
            driver -> ../../../../bus/ap/drivers/<zzz>queue
            ...
        driver -> ../../../bus/ap/drivers/<drv>card
        ...

The two digit <xx> field is the card number, the four digit <yyyy>
field is the queue number and <drv> is the name of the device driver,
e.g. "cex4".

For compatability /sys/bus/ap/card<xx> for the old layout has to exist,
including the attributes that used to reside there.

With additional contributions from Harald Freudenberger and
Martin Schwidefsky.
Signed-off-by: NIngo Tuchscherer <ingo.tuchscherer@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
      e28d2af4
  27. 27 6月, 2016 1 次提交
  29. 15 12月, 2015 1 次提交
  31. 20 10月, 2015 1 次提交
  33. 21 9月, 2015 2 次提交
  35. 07 8月, 2015 1 次提交
  37. 07 7月, 2015 1 次提交
    • S
      ACPI / scan: Add support for ACPI _CLS device matching · 26095a01
      由 Suthikulpanit, Suravee 提交于 
      Device drivers typically use ACPI _HIDs/_CIDs listed in struct device_driver
acpi_match_table to match devices. However, for generic drivers, we do not
want to list _HID for all supported devices. Also, certain classes of devices
do not have _CID (e.g. SATA, USB). Instead, we can leverage ACPI _CLS,
which specifies PCI-defined class code (i.e. base-class, subclass and
programming interface). This patch adds support for matching ACPI devices using
the _CLS method.

To support loadable module, current design uses _HID or _CID to match device's
modalias. With the new way of matching with _CLS this would requires modification
to the current ACPI modalias key to include _CLS. This patch appends PCI-defined
class-code to the existing ACPI modalias as following.

    acpi:<HID>:<CID1>:<CID2>:..:<CIDn>:<bbsspp>:
E.g:
    # cat /sys/devices/platform/AMDI0600:00/modalias
    acpi:AMDI0600:010601:

where bb is th base-class code, ss is te sub-class code, and pp is the
programming interface code

Since there would not be _HID/_CID in the ACPI matching table of the driver,
this patch adds a field to acpi_device_id to specify the matching _CLS.

    static const struct acpi_device_id ahci_acpi_match[] = {
        { ACPI_DEVICE_CLASS(PCI_CLASS_STORAGE_SATA_AHCI, 0xffffff) },
        {},
    };

In this case, the corresponded entry in modules.alias file would be:

    alias acpi*:010601:* ahci_platform
Acked-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: NHanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: NSuravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
      26095a01
  39. 31 5月, 2015 1 次提交
  41. 25 5月, 2015 1 次提交
  43. 14 5月, 2015 1 次提交
    • H
      usb: add bus type for USB ULPI · 289fcff4
      由 Heikki Krogerus 提交于 
      UTMI+ Low Pin Interface (ULPI) is a commonly used PHY
interface for USB 2.0. The ULPI specification describes a
standard set of registers which the vendors can extend for
their specific needs. ULPI PHYs provide often functions
such as charger detection and ADP sensing and probing.

There are two major issues that the bus type is meant to
tackle:

Firstly, ULPI registers are accessed from the controller.
The bus provides convenient method for the controller
drivers to share that access with the actual PHY drivers.

Secondly, there are already platforms that assume ULPI PHYs
are runtime detected, such as many Intel Baytrail based
platforms. They do not provide any kind of hardware
description for the ULPI PHYs like separate ACPI device
object that could be used to enumerate a device from.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NDavid Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
      289fcff4
  45. 31 3月, 2015 1 次提交
    • J
      MIPS: Add CDMM bus support · 8286ae03
      由 James Hogan 提交于 
      Add MIPS Common Device Memory Map (CDMM) support in the form of a bus in
the standard Linux device model. Each device attached via CDMM is
discoverable via an 8-bit type identifier and may contain a number of
blocks of memory mapped registers in the CDMM region. IRQs are expected
to be handled separately.

Due to the per-cpu (per-VPE for MT cores) nature of the CDMM devices,
all the driver callbacks take place from workqueues which are run on the
right CPU for the device in question, so that the driver doesn't need to
be as concerned about which CPU it is running on. Callbacks also exist
for when CPUs are taken offline, so that any per-CPU resources used by
the driver can be disabled so they don't get forcefully migrated. CDMM
devices are created as children of the CPU device they are attached to.

Any existing CDMM configuration by the bootloader will be inherited,
however platforms wishing to enable CDMM should implement the weak
mips_cdmm_phys_base() function (see asm/cdmm.h) so that the bus driver
knows where it should put the CDMM region in the physical address space
if the bootloader hasn't already enabled it.

A mips_cdmm_early_probe() function is also provided to allow early boot
or particularly low level code to set up the CDMM region and probe for a
specific device type, for example early console or KGDB IO drivers for
the EJTAG Fast Debug Channel (FDC) CDMM device.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9599/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      8286ae03
  47. 07 3月, 2015 1 次提交
  49. 12 2月, 2015 2 次提交
  51. 04 2月, 2015 1 次提交
  53. 27 1月, 2015 1 次提交
  55. 29 10月, 2014 1 次提交
  57. 10 4月, 2014 1 次提交
    • B
      x86: LLVMLinux: Fix "incomplete type const struct x86cpu_device_id" · c4586256
      由 Behan Webster 提交于 
      Similar to the fix in 40413dcb

MODULE_DEVICE_TABLE(x86cpu, ...) expects the struct to be called struct
x86cpu_device_id, and not struct x86_cpu_id which is what is used in the rest
of the kernel code.  Although gcc seems to ignore this error, clang fails
without this define to fix the name.

Code from drivers/thermal/x86_pkg_temp_thermal.c
static const struct x86_cpu_id __initconst pkg_temp_thermal_ids[] = { ... };
MODULE_DEVICE_TABLE(x86cpu, pkg_temp_thermal_ids);

Error from clang:
drivers/thermal/x86_pkg_temp_thermal.c:577:1: error: variable has
      incomplete type 'const struct x86cpu_device_id'
MODULE_DEVICE_TABLE(x86cpu, pkg_temp_thermal_ids);
^
include/linux/module.h:145:3: note: expanded from macro
      'MODULE_DEVICE_TABLE'
  MODULE_GENERIC_TABLE(type##_device, name)
  ^
include/linux/module.h:87:32: note: expanded from macro
      'MODULE_GENERIC_TABLE'
extern const struct gtype##_id __mod_##gtype##_table            \
                               ^
<scratch space>:143:1: note: expanded from here
__mod_x86cpu_device_table
^
drivers/thermal/x86_pkg_temp_thermal.c:577:1: note: forward declaration of
      'struct x86cpu_device_id'
include/linux/module.h:145:3: note: expanded from macro
      'MODULE_DEVICE_TABLE'
  MODULE_GENERIC_TABLE(type##_device, name)
  ^
include/linux/module.h:87:21: note: expanded from macro
      'MODULE_GENERIC_TABLE'
extern const struct gtype##_id __mod_##gtype##_table            \
                    ^
<scratch space>:141:1: note: expanded from here
x86cpu_device_id
^
1 error generated.
Signed-off-by: NBehan Webster <behanw@converseincode.com>
Signed-off-by: NJan-Simon Möller <dl9pf@gmx.de>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      c4586256
  59. 01 3月, 2014 1 次提交
  61. 19 2月, 2014 1 次提交
    • A
      cpu: add generic support for CPU feature based module autoloading · 67bad2fd
      由 Ard Biesheuvel 提交于 
      This patch adds support for advertising optional CPU features over udev
using the modalias, and for declaring compatibility with/dependency upon
such a feature in a module.

The mapping between feature numbers and actual features should be provided
by the architecture in a file called <asm/cpufeature.h> which exports the
following functions/macros:
- cpu_feature(FEAT), a preprocessor macro that maps token FEAT to a
  numeric index;
- bool cpu_have_feature(n), returning whether this CPU has support for
  feature #n;
- MAX_CPU_FEATURES, an upper bound for 'n' in the previous function.

The feature can then be enabled by setting CONFIG_GENERIC_CPU_AUTOPROBE
for the architecture.

For instance, a module that registers its module init function using

  module_cpu_feature_match(FEAT_X, module_init_function)

will be probed automatically when the CPU's support for the 'FEAT_X'
feature is advertised over udev, and will only allow the module to be
loaded by hand if the 'FEAT_X' feature is supported.
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      67bad2fd
  63. 16 2月, 2014 1 次提交
  65. 08 9月, 2013 1 次提交
  67. 04 9月, 2013 1 次提交
  69. 19 7月, 2013 1 次提交
    • A
      ssb: fix alignment of struct bcma_device_id · b01a60be
      由 Arnd Bergmann 提交于 
      The ARM OABI and EABI disagree on the alignment of structures
with small members, so module init tools may interpret the
ssb device table incorrectly, as shown  by this warning when
building the b43 device driver in an OABI kernel:

FATAL: drivers/net/wireless/b43/b43: sizeof(struct ssb_device_id)=6 is
not a modulo of the size of section __mod_ssb_device_table=88.

Forcing the default (EABI) alignment on the structure makes this
problem go away. Since the ssb_device_id may have the same problem,
better fix both structures.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
      b01a60be
  71. 04 7月, 2013 2 次提交