Use sdma_engine[8] array instead of sdma_engine0~7 so it is easier
to program.
Signed-off-by: NOak Zeng <Oak.Zeng@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

effect asics: VEGA10 and VEGA12
Signed-off-by: NJim Qu <Jim.Qu@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Page queue is supported on Vega20 with SDMA firmware
123 onwards.
Signed-off-by: NEvan Quan <evan.quan@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Vega20 uses ring id 1 for page queues EOP irq while previous
ASICs take ring id 3.
Signed-off-by: NEvan Quan <evan.quan@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

ASIC specific doorbell layout is used instead of enum definition
Signed-off-by: NOak Zeng <ozeng@amd.com>
Suggested-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Suggested-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Based SDMA fw version to enable has_page_queue support. Have to move
sdma_v4_0_init_microcode from sw_init to early_init, to load firmware
and init fw_version before set_ring/buffer/vm_pte_funcs use it.

v2: don't enable on vega12, 20 until confirmed
Signed-off-by: NPhilip Yang <Philip.Yang@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Because increase SDMA_DOORBELL_RANGE to add new SDMA doorbell for paging queue will
break SRIOV, instead we can reserve and map two doorbell pages for amdgpu, paging
queues doorbell index use same index as SDMA gfx queues index but on second page.

For Vega20, after we change doorbell layout to increase SDMA doorbell for 8 SDMA RLC
queues later, we could use new doorbell index for paging queue.
Signed-off-by: NPhilip Yang <Philip.Yang@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This looks like copy paste typo
Signed-off-by: NPhilip Yang <Philip.Yang@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Use the paging queue for buffer functions to avoid contention
with the other queues.
Reviewed-by: NJunwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Tested-by: NChen Gong <Curry.Gong@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Currently, SDMA page queue is not used under SR-IOV VF, and this queue will
cause ring test failure in amdgpu module reload case. So just disable it.
Signed-off-by: NTrigger Huang <Trigger.Huang@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

there is no functional changes.just
refine function name to keep
consistence with other files.

change amdgpu_get_sdma_instance to
amdgpu_sdma_get_instance_from_ring.
suggested by alex.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NFlora Cui <flora.cui@amd.com>
Signed-off-by: NRex Zhu <Rex.Zhu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

use the point of struct amdgpu_job as the function
argument instand of vmid, so the other members of
struct amdgpu_job can be visit in emit_ib function.

v2: add a wrapper for getting the VMID
    add the job before the ib on the parameter list.
v3: refine the wrapper name
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NRex Zhu <Rex.Zhu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The wptr value will be shitfed when function returns.
Remove the redundant shift and clean up.
Signed-off-by: NJunwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

It blocks most of sanity tests, so disable it for now.
Tested-by: NChen Gong <Curry.Gong@amd.com>
Signed-off-by: NJunwei Zhang <Jerry.Zhang@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

We already print an error message that an IB test failed in the common
code.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NAndrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Move all error messages from IP specific code into the common helper.
This way we now uses the ring name in the messages instead of the index
and note which device is affected as well.

Also cleanup error handling in the IP specific code and consequently use
ETIMEDOUT when the ring test timed out.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NAndrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Start using drm_gpu_scheduler.ready isntead.

v3:
Add helper function to run ring test and set
sched.ready flag status accordingly, clean explicit
sched.ready sets from the IP specific files.

v4: Add kerneldoc and rebase.
Signed-off-by: NAndrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signal a fault to the scheduler on an illegal instruction or register
access violation instead of kicking of the reset handler directly.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Acked-by: NAndrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

For sdma v4, there is bug caused by
commit d4e869b6b5d6 ("drm/amdgpu: add ring test for page queue")'

local variable ring is reused and changed, so amdgpu_ttm_set_buffer_funcs_status(adev, true)
is skipped accidently. As a result, amdgpu_fill_buffer() will fail, kernel message:

[drm:amdgpu_fill_buffer [amdgpu]] *ERROR* Trying to clear memory with ring turned off.
[   25.260444] [drm:amdgpu_fill_buffer [amdgpu]] *ERROR* Trying to clear memory with ring turned off.
[   25.260627] [drm:amdgpu_fill_buffer [amdgpu]] *ERROR* Trying to clear memory with ring turned off.
[   25.290119] [drm:amdgpu_fill_buffer [amdgpu]] *ERROR* Trying to clear memory with ring turned off.
[   25.290370] [drm:amdgpu_fill_buffer [amdgpu]] *ERROR* Trying to clear memory with ring turned off.
[   25.319971] [drm:amdgpu_fill_buffer [amdgpu]] *ERROR* Trying to clear memory with ring turned off.
[   25.320486] amdgpu 0000:19:00.0: [mmhub] VMC page fault (src_id:0 ring:154 vmid:8 pasid:32768, for process  pid 0 thread  pid 0)
[   25.320533] amdgpu 0000:19:00.0:   in page starting at address 0x0000000000000000 from 18
[   25.320563] amdgpu 0000:19:00.0: VM_L2_PROTECTION_FAULT_STATUS:0x00800134
Signed-off-by: NPhilip Yang <Philip.Yang@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

We add page queue for sdma to update page table. So here it also needs ring test
to verify it workable during the initialization.
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Since we see driver loading failure on Vega20. Keep it
disabled until it's ready.
Signed-off-by: NEvan Quan <evan.quan@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Don't use the paging queue on APUs.
Tested-by: NTom St Denis <tom.stdenis@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Only for testing, not sure if we should keep it like this.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Implement all the necessary stuff to get those extra rings working.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Significantly shortens the code.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Just use the same code path for both SRIOV and bare metal.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Needed to start using the paging queue.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Under SRIOV we were enabling the ring buffer before it was initialized.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

need to check adev->powerplay.pp_funcs first, becasue from
AI, the smu ip can be disabled by user, and the pp_handle
is null in this case.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NRex Zhu <Rex.Zhu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Update SDMA golden settings.
Signed-off-by: NEvan Quan <evan.quan@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

smu only expose interface to other ip blocks.
in order to reduce dependence between smu and other ip blocks
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NRex Zhu <Rex.Zhu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NRex Zhu <Rex.Zhu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

We always want those to be setup correctly.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Correct the format

For vega10 sriov, the sdma doorbell must be fixed as follow to keep the
same setting with host driver, or it will happen conflicts.
Signed-off-by: NEmily Deng <Emily.Deng@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Treat them all as Raven rather than adding a new picasso
asic type.  This simplifies a lot of code and also handles the
case of rv2 chips with the 0x15d8 pci id.  It also fixes dmcu
fw handling for picasso.
Acked-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Golden register settings from the hw team.
Signed-off-by: NFeifei Xu <Feifei.Xu@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

use raven2 sdma firmware.
Signed-off-by: NFeifei Xu <Feifei.Xu@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Add sdma support to picasso
Signed-off-by: NLikun Gao <Likun.Gao@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Fix SDMA hang in prt mode, clear XNACK_WATERMARK in reg SDMA0_UTCL1_WATERMK to avoid the issue

Affected ASICs: VEGA10 VEGA12 RV1 RV2

v2: add reg clear for SDMA1
Signed-off-by: NTao Zhou <tao.zhou1@amd.com>
Tested-by: NYukun Li <yukun1.li@amd.com>
Reviewed-by: NHawking Zhang <Hawking.Zhang@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Fix SDMA hang in prt mode, clear XNACK_WATERMARK in reg SDMA0_UTCL1_WATERMK to avoid the issue

Affected ASICs: VEGA10 VEGA12 RV1 RV2

v2: add reg clear for SDMA1
Signed-off-by: NTao Zhou <tao.zhou1@amd.com>
Tested-by: NYukun Li <yukun1.li@amd.com>
Reviewed-by: NHawking Zhang <Hawking.Zhang@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>