Typecast hwrm_cmd_resp_addr to (u8 *) from (void *) before doing
arithmetic.
Signed-off-by: NVenkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for adding a 2nd communication channel to firmware.
Signed-off-by: NVenkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set hwrm_intr_seq_id value to its inverted value instead of
HWRM_SEQ_INVALID, when an hwrm completion of type
CMPL_BASE_TYPE_HWRM_DONE is received. This will enable us to use
the complete 16-bit sequence ID space.
Signed-off-by: NVenkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The major changes are in the flow offload firmware APIs.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the redundant variable initialization,
as driver will devm_kzalloc to set value to hdev soon.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver gets rss information from the last descriptor of the packet.
When driver handle the rss type, ring->next_to_clean indicates the
first descriptor of next packet.

This patch fix the descriptor index with "ring->next_to_clean - 1".

Fixes: 232fc64b ("net: hns3: Add HW RSS hash information to RX skb")
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When user disables flow director, all the rules will be disabled. But
when reset happens, it will restore all the rules again. It's not
reasonable. This patch fixes it by add flow director status check before
restore fules.

Fixes: 6871af29 ("net: hns3: Add reset handle for flow director")
Fixes: c17852a8 ("net: hns3: Add support for enable/disable flow director")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When add flow director fule for vf, the vf id is used as array
subscript before valid checking, which may cause memory overflow.

Fixes: dd74f815 ("net: hns3: Add support for rule add/delete for flow director")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While doing DOWN operation, the driver will reclaim the memory which has
already used for TX. If the hardware is processing this memory, it will
cause a RCB error to the hardware. According the hardware's description,
the driver should reset the tqp before reclaim the memory during DOWN.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Each pf supports max 64 vectors and 128 tqps. For 2p/4p core scenario,
there may be more than 64 cpus online. So the result of min_t(u16,
num_Online_cpus(), tqp_num) may be more than 64. This patch adds check
for the vector number.

Fixes: dd38c726 ("net: hns3: fix for coalesce configuration lost during reset")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

udelay() in driver may always occupancy processor. If there is only
one cpu in system, the VF driver may initialize fail when insmod
PF and VF driver in the same system. This patch use msleep() to free
cpu when VF wait PF message.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In original codes, default tc value is set to the max tc. It's more
reasonable to close tc by changing default tc value to 1. Users can
enable it with lldp tool when they want to use tc.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When triggering nic down, there is a time window between bringing down
the protocol stack and stopping the work task. If the net is up in the
time window, it may bring up the protocol stack again.

This patch fixes it by stop the work task at the beginning of
hns3_nic_net_stop(). To keep symmetrical, start the work task at the
end of hns3_nic_net_open().
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. remove fine-tune property and related setting to simplify
the timing adjustment flow.
2. set timing value according to the value from device tree,
and will not care whether PHY insert internal delay.
Signed-off-by: NBiao Huang <biao.huang@mediatek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previous patches tried to make RIF deletion more robust and avoid
use-after-free situations.

As another precaution, hold a reference on a RIF's netdev and release it
when the RIF is deleted.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the past we had multiple instances where RIFs were not properly
deleted.

One of the reasons for leaking a RIF was that at the time when IP
addresses were flushed from the respective netdev (prompting the
destruction of the RIF), the netdev was no longer a mlxsw upper. This
caused the inet{,6}addr notification blocks to ignore the NETDEV_DOWN
event and leak the RIF.

Instead of checking whether the netdev is our upper when an IP address
is removed, we can instead check if the netdev has a RIF configured.

To look up a RIF we need to access mlxsw private data, so the patch
stores the notification blocks inside a mlxsw struct. This then allows
us to use container_of() and extract the required private data.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Next patch is going to make RIF deletion more robust by removing
reliance on fragile mlxsw_sp_lower_get(). This is because a netdev is
not necessarily our upper anymore when its IP addresses are flushed.

The inet{,6}addr notification blocks are going to resolve 'struct
mlxsw_sp' using container_of(), but the functions they call still use
mlxsw_sp_lower_get().

As a preparation for the next patch, propagate 'struct mlxsw_sp' down to
the functions called from the notification blocks and remove reliance on
mlxsw_sp_lower_get().
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a LAG device or a VLAN device on top of it is enslaved to a bridge,
the driver propagates the CHANGEUPPER event to the LAG's slaves.

This causes each physical port to increase the reference count of the
internal representation of the bridge port by calling
mlxsw_sp_port_bridge_join().

However, when a port is removed from a LAG, the corresponding leave()
function is not called and the reference count is not decremented. This
leads to ugly hacks such as mlxsw_sp_bridge_port_should_destroy() that
try to understand if the bridge port should be destroyed even when its
reference count is not 0.

Instead, make sure that when a port is unlinked from a LAG it would see
the same events as if the LAG (or its uppers) were unlinked from a
bridge.

The above is achieved by walking the LAG's uppers when a port is
unlinked and calling mlxsw_sp_port_bridge_leave() for each upper that is
enslaved to a bridge.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit b3529af6 ("spectrum: Reference count VLAN entries") started
reference counting port-VLAN entries in a similar fashion to the 8021q
driver.

However, this is not actually needed and only complicates things.
Instead, the driver should forbid the creation of a VLAN on a port if
this VLAN already exists. This would also solve the issue fixed by the
mentioned commit.

Therefore, remove the get()/put() API and use create()/destroy()
instead.

One place that needs special attention is VLAN addition in a VLAN-aware
bridge via switchdev operations. In case the VLAN flags (e.g., 'pvid')
are toggled, then the VLAN entry already exists. To prevent the driver
from wrongly returning EEXIST, the driver is changed to check in the
prepare phase whether the entry already exists and only returns an error
in case it is not associated with the correct bridge port.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 993107fe ("mlxsw: spectrum_switchdev: Fix VLAN device
deletion via ioctl") I fixed a bug caused by the fact that the driver
views differently the deletion of a VLAN device when it is deleted via
an ioctl and netlink.

Instead of relying on a specific order of events (device being
unregistered vs. VLAN filter being updated), simply make sure that the
driver performs the necessary cleanup when the VLAN device is unlinked,
which always happens before the other two events.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This function is no longer used. Remove it.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, when a RIF is constructed on top of a FID, the RIF increments
the FID's reference count and the RIF is destroyed when the FID's
reference count drops to 1. This effectively means that when no local
ports are member in the FID, the FID is destroyed regardless if the
router port is a member in the FID or not.

The above can lead to the unexpected behavior in which routes using a
VLAN interface as their nexthop device are no longer offloaded after the
last local port leaves the corresponding VLAN (FID).

Example:
# ip -4 route show dev br0.10
192.0.2.0/24 proto kernel scope link src 192.0.2.1 offload
# bridge vlan del vid 10 dev swp3
# ip -4 route show dev br0.10
192.0.2.0/24 proto kernel scope link src 192.0.2.1

After the patch, the route is offloaded before and after the VLAN is
removed from local port 'swp3', as the RIF corresponding to 'br0.10'
continues to exists.

In order to remove RIFs' reliance on the underlying FID's reference
count, we need to add a reference count to sub-port RIFs, which are RIFs
that correspond to physical ports and their uppers (e.g., LAG devices).

In this case, each {Port, VID} ('struct mlxsw_sp_port_vlan') needs to
hold a reference on the RIF. For example:

                       bond0.10
                          |
                        bond0
                          |
                      +-------+
                      |       |
                    swp1    swp2

Both {Port 1, VID 10} and {Port 2, VID 10} will hold a reference on the
RIF corresponding to 'bond0.10'. When the last reference is dropped, the
RIF will be destroyed.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, only VRF and macvlan uppers are supported on top of VLAN
device configured over a bridge, so make sure the driver forbids other
uppers.

Note that enslavement to a VRF is handled earlier in the notification
block, so there is no need to check for a VRF upper here.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

secpath_set is a wrapper for secpath_dup that will not perform
an allocation if the secpath attached to the skb has a reference count
of one, i.e., it doesn't need to be COW'ed.

Also, secpath_dup doesn't attach the secpath to the skb, it leaves
this to the caller.

Use secpath_set in places that immediately assign the return value to
skb.

This allows to remove skb->sp without touching these spots again.

secpath_dup can eventually be removed in followup patch.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Will avoid touching this when sp pointer is removed from sk_buff struct.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use skb_sec_path and secpath_exists helpers where possible.
This reduces noise in followup patch that removes skb->sp pointer.

v2: no changes, preseve acks from v1.
Acked-by: NShannon Nelson <shannon.lee.nelson@gmail.com>
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add statistics for pending frames in Rx/Tx conf FQs and
number of buffers in pool. Available through ethtool -S.
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NIoana ciornei <ioana.ciornei@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After phy_start() phylib takes care of all needed actions, including
aneg settings and checking link state. There's no need to set state
PHY_CHANGELINK in drivers.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:1070:5: warning:
 variable 'op' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:1342:5: warning:
 variable 'cmd_op' set but not used [-Wunused-but-set-variable]

'op' never used since introduction in commit 7cb03b23 ("qlcnic:
Support VF-PF communication channel commands.")
'cmd_op' not used since commit 6226204b ("qlcnic: Fix operation
type and command type.")
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's a workaround to restart the phylib state machine in case of a
MDIO access timeout. Seems it was introduced to deal with the
consequences of a too small MDIO timeout. See also commit message of
c3b084c2 ("net: fec: Adjust ENET MDIO timeouts") which increased
the timeout value later. Due to the later timeout value fix it seems
to be safe to remove the workaround.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When caculating the SSU buffer, it first allocate tx and
rx private buffer, then the remaining buffer is for rx
shared buffer. The remaining buffer size should be at
least bigger than or equal to the shared_std, which is the
minimum shared buffer size required by the driver, but
currently if the remaining buffer size is equal to the
shared_std, it returns failure, which causes SSU buffer
allocation failure problem.

This patch fixes this problem by rounding up shared_std before
checking the the remaining buffer size bigger than or equal to
the shared_std.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The hardware expects the buffer size set to SSU is aligned to
256 bytes, this patch aligns the buffer size to 256 byte using
roundup or rounddown function.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support of getting tx and dv buffer size through
firmware, because different version of hardware requires different
size of tx and dv buffer.

This patch also add dv_buf_size to tc' private buffer size even if
pfc is not enable for the tc.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver calls phy_connect_direct and registers hclge_mac_adjust_link
to synchronize mac speed and duplex from phy. It is better to
synchronize mac speed and duplex from phy when phy link up.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Our phy does not support 1000M/half, this patch removes 1000M/half from
PHY_SUPPORTED_FEATURES.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

coalesce param updates every 100 napi times, it may update a little
late if ping test after a high rate flow, may over napi poll is called
100 times as ping test sends packets every second.

This patch updates coalesce param every second, instead with every
100 napi times. It can not update the param 100% in time, but the
lag time is very short.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the hns3_nic_uninit_vector_data(), the procedure of uninitializing
the tqp_vector's IRQ has not set affinity_notify to NULL and changes
its init flag. This patch fixes it. And for simplificaton, local
variable tqp_vector is used instead of priv->tqp_vector[i].

Fixes: 424eb834 ("net: hns3: Unified HNS3 {VF|PF} Ethernet Driver for hip08 SoC")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When doing reset, it is unnecessary to get the hardware's default
configuration again, otherwise, the user's configuration will be
overwritten.

Fixes: 4ed340ab ("net: hns3: Add reset process in hclge_main")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When hclge_reset() completes successfully, it should update the
last_reset_time, set reset_fail_cnt to 0, and set reset_type of
hnae3_ae_dev to HNAE3_NONE_RESET.

Also when hclgevf_reset() completes successfully, it should update
the last_reset_time, and set reset_type of hnae3_ae_dev to
HNAE3_NONE_RESET.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While doing DOWN, the calling of napi_disable() may not return, since the
napi_complete() in the hns3_nic_common_poll() will never be called when
HNS3_NIC_STATE_DOWN is set. So we need to call napi_complete() before
checking HNS3_NIC_STETE_DOWN.

Fixes: ff0699e0 ("net: hns3: stop napi polling when HNS3_NIC_STATE_DOWN is set")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>