Disable the card clock during automatic pad drive strength calibration
and re-enable it afterwards.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Automatic pad drive strength calibration is performed on a separate pad
identical to the ones used for driving the actual bus. Power on the
calibration pad during the calibration procedure and power it off
afterwards to save power.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Reviewed-by: NMikko Perttunen <mperttunen@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Configure the voltage reference used by the automatic pad drive strength
calibration procedure. The value is a magic number from the TRM.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Implement polling with 10 ms timeout for automatic pad drive strength
calibration.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Parse the pinctrl state and nvidia,only-1-8-v properties from the device
tree. Validate the pinctrl and regulator configuration before unmasking
UHS modes. Implement pad voltage state reconfiguration in the mmc
start_signal_voltage_switch() callback. Add NVQUIRK_NEEDS_PAD_CONTROL
and add set it for Tegra210 and Tegra186.

The pad configuration is done in the mmc callback because the order of
pad reconfiguration and sdhci voltage switch depend on the voltage to
which the transition occurs.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Document the Tegra SDHCI inbound and outbound sampling trimmer values.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Reviewed-by: NRob Herring <robh@kernel.org>
Acked-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add bindings documentation for pad pull up and pull down offset values to be
programmed before executing automatic pad drive strength calibration.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Reviewed-by: NRob Herring <robh@kernel.org>
Acked-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Document the pinctrl bindings used by the SDHCI driver to reconfigure
pad voltages on controllers supporting multiple voltage levels.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Reviewed-by: NMikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: NRob Herring <robh@kernel.org>
Acked-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This variable is unused now after some refactoring.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Concise, but still readable.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

SDR104, HS200 and HS400 need to check for SCC error. If SCC error is
detected, retuning is necessary.
Signed-off-by: NMasaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
[Niklas: update commit message]
Signed-off-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Checking for SCC error during retuning is unnecessary.
Signed-off-by: NMasaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
[Niklas: fix small style issue]
Signed-off-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add a helper to allow host drivers checking if a retune is in progress.
Signed-off-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

for (clk = 0x80000080; new_clock >= (clock << 1); clk >>= 1)
          clock <<= 1;

... is too tricky, hence I replaced with

  roundup_pow_of_two(divisor) >> 2

'(clk >> 22) & 0x1' is the bit test for the 1/1 divisor, but
it is not clear.  'divisor <= 1' is easier to understand.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

renesas_sdhi_clk_start() and renesas_sdhi_clk_stop() are now only
called from renesas_sdhi_set_clock().  Merge them.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

When using DMA, if the DMA addr spans 128MB boundary, we have to split
the DMA transfer into two so that each one doesn't exceed the boundary.
Signed-off-by: NJisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add this hook so that it can be overridden with driver specific
implementations. We also let the original sdhci_adma_write_desc()
accept &desc so that the function can set its new value. Then export
the function so that it could be reused by driver's specific
implementations.
Signed-off-by: NJisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch adds adma_table_cnt member to struct sdhci_host to give more
flexibility to drivers to control the ADMA table count.

Default value of adma_table_cnt is set to (SDHCI_MAX_SEGS * 2 + 1).
Signed-off-by: NJisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.

Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Hu Ziji <huziji@marvell.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: NRob Herring <robh@kernel.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Allow SDHCI drivers to hook code before and after sdhci_request() by
making it externally visible.
Signed-off-by: NAapo Vienamo <avienamo@nvidia.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

After host requests RESET_FOR_ALL action, the hardware output an
interrupt for OS and waiting for the OS to approve.

Before writing this fix, ACPI GED has handled the interrupt. But
the ACPI GED belongs to a slow process, and sometimes the handling
process time is more than 100ms(Mutex wait more than 100ms). So
drop the GED solution and add this quirk fix.
Signed-off-by: NWang Dongsheng <dongsheng.wang@hxt-semitech.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The device specific resource can be free in free_slot after
removing host controller.
Signed-off-by: NWang Dongsheng <dongsheng.wang@hxt-semitech.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In tuning mode of operation, when TBCTL[TB_EN] is set, eSDHC may report
one of the following errors :
1)Tuning error while running tuning operation where SYSCTL2[SAMPCLKSEL]
will not get set even when SYSCTL2[EXTN] is reset. OR
2)Data transaction error (e.g. IRQSTAT[DCE], IRQSTAT[DEBE]) during data
transaction errors.
This issue occurs when the data window sampled within eSDHC is in full
cycle. So, in that case, eSDHC is not able to find out the start and
end points of the data window and sets the sampling pointer at default
location (which is middle of the internal SD clock). If this sampling
point coincides with the data eye boundary, then it can result in the
above mentioned errors. Impact: Tuning mode of operation for SDR50,
SDR104 or HS200 speed modes may not work properly
Workaround: In case eSDHC reports tuning error or data errors in tuning
mode of operation, by add the erratum A008171 support to fix the issue.
Signed-off-by: NYinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch is to add tuning error codes to
judge tuning state
Signed-off-by: NYinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Here is another TMIO MMC variant found in Socionext UniPhier SoCs.

As commit b6147490 ("mmc: tmio: split core functionality, DMA and
MFD glue") said, these MMC controllers use the IP from Panasonic.

However, the MMC controller in the TMIO (Toshiba Mobile IO) MFD chip
was the first upstreamed user of this IP.  The common driver code
for this IP is now called 'tmio-mmc-core' in Linux although it is a
historical misnomer.

Anyway, this driver select's MMC_TMIO_CORE to borrow the common code
from tmio-mmc-core.c

Older UniPhier SoCs (LD4, Pro4, sLD8) support the external DMA engine
like renesas_sdhi_sys_dmac.c.  The difference is UniPhier SoCs use a
single DMA channel whereas Renesas chips request separate channels for
RX and TX.

Newer UniPhier SoCs (Pro5 and later) support the internal DMA engine
like renesas_sdhi_internal_dmac.c  The register map is almost the same,
so I guess Renesas and Socionext use the same internal DMA hardware.
The main difference is, the register offsets are doubled for Renesas.

                        Renesas      Socionext
                        SDHI         UniPhier
  DM_CM_DTRAN_MODE      0x820        0x410
  DM_CM_DTRAN_CTRL      0x828        0x414
  DM_CM_RST             0x830        0x418
  DM_CM_INFO1           0x840        0x420
  DM_CM_INFO1_MASK      0x848        0x424
  DM_CM_INFO2           0x850        0x428
  DM_CM_INFO2_MASK      0x858        0x42c
  DM_DTRAN_ADDR         0x880        0x440
  DM_DTRAN_ADDREX        ---         0x444

This comes from the difference of host->bus_shift; 2 for Renesas SoCs,
and 1 for UniPhier SoCs.  Also, the datasheet for UniPhier SoCs defines
DM_DTRAN_ADDR and DM_DTRAN_ADDREX as two separate registers.

It could be possible to factor out the DMA common code by introducing
some hooks to cope with platform quirks, but this patch does not touch
that for now.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This SD/eMMC controller is used for UniPhier SoC family.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NRob Herring <robh@kernel.org>
Acked-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

tmio_mmc_set_clock() is full of quirks because different SoC vendors
extended this in different ways.

The original IP defines the divisor range 1/2 ... 1/512.

 bit 7 is set:    1/512
 bit 6 is set:    1/256
   ...
 bit 0 is set:    1/4
 all bits clear:  1/2

It is platform-dependent how to achieve the 1/1 clock.

I guess the TMIO-MFD variant uses the clock selector outside of this IP,
as far as I see tmio_core_mmc_clk_div() in drivers/mfd/tmio_core.c

I guess bit[7:0]=0xff is Renesas-specific extension.

Socionext (and Panasonic) uses bit 10 (CLKSEL) for 1/1.  Also, newer
versions of UniPhier SoC variants use bit 16 for 1/1024.

host->clk_update() is only used by the Renesas variants, whereas
host->set_clk_div() is only used by the TMIO-MFD variants.

To cope with this mess, promote tmio_mmc_set_clock() to a new
platform hook ->set_clock(), and melt the old two hooks into it.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

tmio_mmc_clk_stop(host) is equivalent to tmio_mmc_set_clock(host, 0).
This replacement is needed for the next commit.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The JZ4725B is the first JZ SoC version that introduced a 32-bit IMASK
register, not the JZ4750.
Signed-off-by: NPaul Cercueil <paul@crapouillou.net>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Document the R-Car V3M (R8A77970) SoC in the R-Car SDHI bindings -- it's
the usual R-Car gen3 compatible controller with the internal DMA engine.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>

I've successfully tested eMMC on the V3H Starter Kit board and since the
R8A77970 SoC has a single SDHI core, it can't be a subject to the known RX
DMA errata.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>

Remove the stray underscore in the DM_CM_DTRAN_MODE.BUS_WIDTH register
field name and fix the typo in the comment of the #define
DTRAN_MODE_CH_NUM_CH1.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Depending on MACH_JZ4740 | MACH_JZ4780 prevent us from creating a generic
kernel that works on more than one MIPS board. Instead, we just depend on
MIPS being set.
Signed-off-by: NPaul Cercueil <paul@crapouillou.net>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Enable access to the RPMB on the on-board eMMC of the
Poplar board.
Signed-off-by: NIgor Opaniuk <igor.opaniuk@linaro.org>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Document RZ/G2M (R8A774A1) SoC bindings.
Signed-off-by: NFabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: NBiju Das <biju.das@bp.renesas.com>
Reviewed-by: NRob Herring <robh@kernel.org>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

We need r8a774a1 to be whitelisted for SDHI to work on the RZ/G2M,
but we don't care about the revision of the SoC, so just whitelist
the generic part number.
Signed-off-by: NFabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: NBiju Das <biju.das@bp.renesas.com>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

When mmc-pwrseq property is passed mmc_pwrseq_alloc() can return
-EPROBE_DEFER because driver for power sequence provider is not probed
yet. Do not show error message when this situation happens.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add ACPI support to all IPROC SDHCI variants.
Signed-off-by: NSrinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: NRay Jui <ray.jui@broadcom.com>
Reviewed-by: NScott Branden <scott.branden@broadcom.com>
Reviewed-by: NVladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Convert DT properties to generic device properties
so that drivers can get properties from DT or ACPI.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Tested-by: NSrinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>