This patch adds cache feature of eMMC4.5 Spec.
If device supports cache capability, host can utilize some specific
operations.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch will apply the generic CMD6 timeout to switch command
for power class.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

MMC v4.5 supports the DISCARD feature (CMD38).  It's different from
trim and there's no check bit.  Currently it's only supported at v4.5.
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

In the v4.5, there's no secure erase & trim support.
Instead it supports the sanitize feature.
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

In dw_mmc 2.40a spec, Data register's offset is changed.
Before we used Data register offset 0x100. but if somebody uses a
2.40a controller, we must use 0x200 for Data register.

This patch adds a version-id checking point and uses SDMMC_DATA(x)
instead of SDMMC_DATA.  It assumes 2.40a is the latest version.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Only allow runtime PM for devices that specifically indicate
that they support it.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Go through the driver's set_power() functions rather than
calling regulator_enable/disable() directly because otherwise
pbias configuration for MMC1 is not done.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Acked-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds support for the power off notify feature, available in
eMMC 4.5 devices. If the host has support for this feature, then the
mmc core will notify the device by setting the POWER_OFF_NOTIFICATION
byte in the extended csd register with a value of 1 (POWER_ON).

For suspend mode short timeout is used, whereas for the normal poweroff
long timeout is used.
Signed-off-by: NGirish K S <girish.shivananjappa@linaro.org>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

sc->clk_bus[ptr] could be NULL.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

All the files using printk function for displaying kernel messages
in the mmc driver have been replaced with corresponding macro.
Signed-off-by: NGirish K S <girish.shivananjappa@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

EXT_CSD[248] includes the default maximum timeout for CMD6.
This field is added at eMMC4.5 Spec. And it can be used for default
timeout except for some operations which don't define the timeout
(i.e. background operation, sanitize, flush cache) in eMMC4.5 Spec.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Ths patch allows runtime PM for sdhci-pci, runtime suspending after
inactivity of 50ms and ensuring runtime resume before SDHC registers
are accessed.  During runtime suspend, interrupts are masked.
The host controller state is restored at runtime resume.

For Medfield, the host controller's card detect mechanism is
supplanted by an always-on GPIO which provides for card detect wake-up.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

mmc_request_done() is sometimes called from interrupt or other atomic
context.  Mostly all mmc_request_done() does is complete(), however it
contains code to retry on error, which uses ->request().  As the error
path is certainly not performance critical, this may be moved to the
waiting function mmc_wait_for_req_done().

This allows ->request() to use runtime PM get_sync() and guarantee it
is never in an atomic context.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NUlf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

We are cleaning up the implicit presence of module.h; these guys are
some of the people who just assume it will be there.  Call it out
explitly for those that really need it.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Commit "mmc: add module param to set fault injection attributes" adds
a module_param to this file.  But it is relying on the old implicit
"module.h is everywhere" behaviour, and without the explicit include
of moduleparam.h, the pending module.h split up produces this error:

core/debugfs.c:28:35: error: expected ')' before numeric constant
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

It allows gerneral purpose partitions in MMC Device.  And I try to simply
make mmc_blk_alloc_parts using mmc_part structure suggested by Andrei
Warkentin.  After patching, we see general purpose partitions like this:
> cat /proc/partitions
          179 0 847872 mmcblk0
          179 192 4096 mmcblk0gp3
          179 160 4096 mmcblk0gp2
          179 128 4096 mmcblk0gp1
          179 96  1052672 mmcblk0gp0
          179 64  1024 mmcblk0boot1
          179 32  1024 mmcblk0boot0
Signed-off-by: NNamjae Jeon <linkinjeon@gmail.com>
Acked-by: NAndrei Warkentin <awarkentin@vmware.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

f39b2dd9 ("mmc: core: Bus width testing needs to handle suspend/resume")
added code to only compare read-only ext_csd fields in bus width testing
code, yet it's comparing some fields that are never set.

The affected fields are ext_csd.raw_erased_mem_count and
ext_csd.raw_partition_support.
Signed-off-by: NAndrei Warkentin <andrey.warkentin@gmail.com>
Acked-by: NPhilip Rakity <prakity@marvell.com>
Cc: <stable@kernel.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Since commit [e58aa3d2: genirq: Run irq handlers with interrupts
disabled], we run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler returns with
interrupts enabled (see commit [b738a50a: genirq: Warn when handler
enables interrupts]).

So now this flag is a NOOP and can be removed.
Signed-off-by: NYong Zhang <yong.zhang0@gmail.com>
Acked-by: NKishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Intel Medfield platform blocks access to eMMC boot partitions which
results in switch errors.  Since there is no access, mmcboot0/1
devices should not be created.  Add a host capability to reflect that.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

In the case of a switch error, do not update partition config as though
the switch succeeded, and ensure blk_end_request is called on the
failed request.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NAndrei Warkentin <andrey.warkentin@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds the power class selection feature available for mmc
versions 4.0 and above.  During the enumeration stage before switching
to the lower data bus, check if the power class is supported for the
current bus width. If the power class is available then switch to the
power class and use the higher data bus. If power class is not supported
then switch to the lower data bus in a worst case.
Signed-off-by: NGirish K S <girish.shivananjappa@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NPer Forlin <per.forlin@linaro.org>
Reviewed-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Replace setup("fail_mmc_request") and faulty "ifdef KERNEL" with
a simple module_param(). The module param mmc_core.fail_request
may be used to set the fault injection attributes during boot time
or module load time.
Signed-off-by: NPer Forlin <per.forlin@linaro.org>
Reviewed-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

mmc_core module needs to use setup_fault_attr() in order
to set fault injection attributes during module load time.
Signed-off-by: NPer Forlin <per.forlin@linaro.org>
Reviewed-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds the basic support for imx6q usdhc, which is a
derivative of esdhc controller.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

This is a minor fix. It makes mmc_ios_show print proper string when the
host's timing is one of the newly added UHS-I modes.
Signed-off-by: NAaron Lu <aaron.lu@amd.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Provide platforms with a simplified way to specify MMCIF DMA slave IDs in
a way, similar to SDHI and other sh_dma clients.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

For cards that support hardware reset (just eMMC), try a reset and
retry before returning an I/O error.  However this is not done for
ECC errors and is never done twice for the same operation type
(READ, WRITE, DISCARD, SECURE DISCARD) until that type of operation
again succeeds.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

MMC core provides a checking function that checks if the reset
has happended.  Add a test to use that function.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Implement eMMC hardware reset for Medfield.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add an SDHCI operation for hardware reset and connect it to the
host controller operation.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

eMMC's may have a hardware reset line.  This patch provides a
host controller operation to implement hardware reset and
a function to reset and reinitialize the card.  Also, for MMC,
the reset is always performed before initialization.

The host must set the new host capability MMC_CAP_HW_RESET
to enable hardware reset.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The error condition indicates that mmci_post_request() should cleanup
after the mmci_pre_request(). In this case the resources allocated by
device_prep_slave_sg() are freed by calling dmaengine_terminate_all().
dma_unmap_sg() should always be performed if the host_cookie is set.
Signed-off-by: NPer Forlin <per.forlin@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

The err condition in post_req() is set to undo a call made to pre_req()
that hasn't been started yet.  The err condition is not set if an MMC
request returns an error.
Signed-off-by: NPer Forlin <per.forlin@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Earlier all cards where initiated with bus mode set as OPENDRAIN, and then
later switched to PUSHPULL. According to the MMC/SD/SDIO specifications
only MMC cards use OPENDRAIN during init. For both SD and SDIO the bus
mode shall be PUSHPULL before attempting to init the card.

The consequence of having incorrect bus mode can lead to not being able
to detect the card. Therefore the default behavior have now been changed
to PUSHPULL in mmc_power_up, and will only be temporarily switched when
trying to attach or init a MMC card.
Signed-off-by: NStefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: NUlf HANSSON <ulf.hansson@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Adds a quirk which can be turned on for SDIO devices that do not support
512 byte requests in byte mode during CMD53. These requests will always
be sent in block mode instead.

This patch also enables this quirk for ST-Ericsson CW1200 WLAN device.
Signed-off-by: NStefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: NUlf HANSSON <ulf.hansson@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NTanmay Upadhyay <tanmay.upadhyay@einfochips.com>
Acked-by: NZhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

During a rescan operation mmc_attach(sd|mmc|sdio) functions are
called. The error handling in these function can trigger a detach
of the bus, which also meant a power off. This is not notified by
the rescan operation which then continues to the next attach function.

If a power off has been done, the framework must never send any
new commands to the host driver, without first doing a new power up.
This will most likely trigger any host driver to hang.

Moving power off out of detach and instead handle power off
separately when it is actually needed, solves the issue.
Signed-off-by: NUlf Hansson <ulf.hansson@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Currently if card_power_gpio is passed from platform data, it is acquired
and its value is either set or reset. After that we overwrite it with 1,
which is not required.

So, this patch removes the extra line which sets its value.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Freescale eSDHC registers only support 32-bit accesses, this patch
ensures that all Freescale eSDHC register accesses are 32-bit.
Signed-off-by: NXu lei <B33228@freescale.com>
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Acked-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>