The following patch adds support for streams
to dwc3 driver.

While at that, also fix one small issue on
endpoint disable where we should clear all
flags not only ENABLED.
Reviewied-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We already have the value from gadget drivers,
just need to pass it to our controller.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix offset calculation in dwc3_trb_dma_offset()
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This makes DWC3_EP_WEDGE do the right thing, which is
prevent DWC3_EP_WEDGE from ever being cleared by a
ClearFeature(HALT) command.

[ balbi@ti.com : allowed set_wedge to send SetHalt command
	to controller ]
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

An older version of the databook said to wait for the FIFO to
drain, but that has been removed from the newer databooks.

Waiting for RxFIFO to drain caused problems when testing against
one of the host controllers available in the market.

After talking to one of the RTL engineers, he stated that we
should _not_ wait for RxFIFO to drain.
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

DEPSTARTCFG for non-EP0 EPs must only be sent once per config

[ balbi@ti.com : changed config_start to start_config_issued ]
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some people think that this line is not compatible with the GPL. The
statement was required due to the Buenos Aires Convention and is now
deprecated. I remove it because it is said that it is pointless nowdays.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use "ep0in" and "ep0out" instead "ep1in" and "ep0out" which is confusing
and not consistent with the remaining output.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We already give requests back in dwc3_ep0_stall_and_restart() so
doing it again here will most likely corrupt the list.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The way it was before was really meaningless.
Now it looks saner.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We don't need to care about direction on a two stage
transfer.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

According to USB 3.0 Specification, a SetAddress()
while device is in Configured State has an unspecified
behavior (see Section 9.4.6). Still USB30CV wasn't
happy with my Stall reply.

To make that thing happy, just accept the SetAddress()
always. No problems have been observed thus far.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

My webcam is a Logitech C300 and I get "chipmunk"ed squeaky sound.
The following trivial patch fixes it.
Signed-off-by: NJon Levell <linuxusb@coralbark.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add to the dev_state and alloc_async structures the user namespace
corresponding to the uid and euid.  Pass these to kill_pid_info_as_uid(),
which can then implement a proper, user-namespace-aware uid check.

Changelog:
Sep 20: Per Oleg's suggestion: Instead of caching and passing user namespace,
	uid, and euid each separately, pass a struct cred.
Sep 26: Address Alan Stern's comments: don't define a struct cred at
	usbdev_open(), and take and put a cred at async_completed() to
	ensure it lasts for the duration of kill_pid_info_as_cred().
Signed-off-by: NSerge Hallyn <serge.hallyn@canonical.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

"length" is type size_t so the cast to unsigned int truncates the
upper bytes.  This isn't an issue in real life (I've checked the
callers) but it's a bit messy.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

add device ID for "HP un2430 Mobile Broadband Module"
Signed-off-by: NRigbert Hamisch <rigbert@gmx.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In the usb printer class specific request get_device_id the value of
wIndex is (interface << 8 | altsetting) instead of just interface.
This enables the detection of some printers with libusb.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NMatthias Dellweg <2500@gmx.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Alan Stern points out that after spin_unlock(&ps->lock) there is no
guarantee that ps->pid won't be freed.  Since kill_pid_info_as_uid() is
called after the spin_unlock(), the pid passed to it must be pinned.
Reported-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NSerge Hallyn <serge.hallyn@canonical.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1488) improves the comments and logic in uhci-hcd's
suspend routine.  The existing comments are hard to understand and
don't give a good idea of what's really going on.

The question of whether EGSM (Enter Global Suspend Mode) and RD
(enable Resume Detect interrupts) can be useful when they're not both
set is difficult.  The spec doesn't give any details on how they
interact with system wakeup, although clearly they are meant to be
used together.  To be safe, the patch changes the subroutine so that
neither bit gets set unless they both do.  There shouldn't be any
functional changes from this; only systems that are designed badly or
broken in some way need to avoid using those bits.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1486) implements the kernel's new wakeup policy for USB
host controllers.  Since they don't generate wakeup requests on their
but merely forward requests from their root hubs toward the CPU, they
should be enabled for wakeup by default.

Also, to be compliant with both the old and new policies, root hubs
should not be enabled for remote wakeup by default.  Userspace must
enable it explicitly if it is desired.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This removes the need of ifdefs within the init function and with it the
headache about the correct clean without bus X but with bus/platform Y &
Z.
xhci-pci is only compiled if CONFIG_PCI is selected which can be
de-selected now without trouble. For now the result is kinda useless
because we have no other glue code. However, since nobody is using
USB_ARCH_HAS_XHCI then it should not be an issue :)
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

xhci_gen_setup() is generic so it can be used to perform the bare xhci
setup even on non-pci based platform. The typedef for the function
pointer is moved into the headerfile
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

xhci_pci_setup() is split into three pieces:

- xhci_gen_setup()
  The major remaining of xhci_pci_setup() is now containing the generic
  part of the xhci setup. It allocates the xhci struct, setup
  hcs_params? and friends, performs xhci_halt(), xhci_init and so one.
  It also obtains the quirks via a callback
- xhci_pci_quirks()
  It checks the origin of the xhci core and sets core specific quirks.
- xhci_pci_setup()
  PCI specific setup functions. Besides calling xhci_gen_setup() with
  xhci_pci_quirks() as an argument it performs PCI specific setup like
  obtaining the address of sbrn via a PCI config space.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

pci_*_consistent() calls dma_*_coherent() with GFP_ATOMIC and requires
pci_dev struct. This is a preparion for later where we no longer have
the pci struct around.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The MSI related fuctionality requires a few structs which are not
available if CONFIG_PCI is not enabled. This is a prepartion to allow
xhci be built without CONFIG_PCI set.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch moves the complete MSI/MSI-X/Legacy dance into its own
function. There is however one difference: If the XHCI_BROKEN_MSI flag
is set then we don't free and register the irq, we simply return.
This is preparation for later PCI decouple.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

to make it look like OHCI and EHCI, we introduce
that symbol and USB_XHCI_HCD depend on that
instead of PCI.

[bigeasy@linutronix.de: wire up USB_ARCH_HAS_HCD]
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix the debug message in xhci_address_device().
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Setting the chain (CH) bit in the link TRB of isochronous transfer rings
is required by AMD 0.96 xHCI host controller to successfully transverse
multi-TRB TD that span through different memory segments.

When a Missed Service Error event occurs, if the chain bit is not set in
the link TRB and the host skips TDs which just across a link TRB, the
host may falsely recognize the link TRB as a normal TRB. You can see
this may cause big trouble - the host does not jump to the right address
which is pointed by the link TRB, but continue fetching the memory which
is after the link TRB address, which may not even belong to the host,
and the result cannot be predicted.

This causes some big problems. Without the former patch I sent: "xHCI:
prevent infinite loop when processing MSE event", the system may hang.
With that patch applied, system does not hang, but the host still access
wrong memory address and isoc transfer will fail. With this patch,
isochronous transfer works as expected.

This patch should be applied to kernels as old as 2.6.36, which was when
the first isochronous support was added for the xHCI host controller.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds sysfs support to xHCI usb2 hardware LPM, so developer can
enable and disable usb2 hardware LPM manually for test purpose.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If the device pass the USB2 software LPM and the host supports hardware
LPM, enable hardware LPM for the device to let the host decide when to
put the link into lower power state.

If hardware LPM is enabled for a port and driver wants to put it into
suspend, it must first disable hardware LPM, resume the port into U0,
and then suspend the port.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch tests USB2 software LPM for a USB2 LPM-capable device.

When a lpm-capable device is addressed, if the host also supports software
LPM, apply a test by putting the device into L1 state and resume it to see
if the device can do L1 suspend/resume successfully.

If the device fails to enter L1 or resume from L1 state, it may not
function normally and usbcore may disconnect and re-enumerate it. In this
case, store the device's Vid and Pid information, make sure the host will
not test LPM for it twice.

The test result is per device/host. Some devices claim to be lpm-capable,
but fail to enter L1 or resume. So the test is necessary.

The xHCI 1.0 errata has modified the USB2.0 LPM implementation. It redefines
the HIRD field to BESL, and adds another register Port Hardware LPM Control
(PORTHLPMC). However, this should not affect the LPM behavior on xHC which
does not implement 1.0 errata.

USB2.0 LPM errata defines a new bit BESL in the device's USB 2.0 extension
descriptor. If the device reports it uses BESL, driver should use BESL
instead of HIRD for it.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Check the host's USB2 LPM capability.

USB2 software LPM support is optional for xHCI 0.96 hosts. xHCI 1.0 hosts
should support software LPM, and may support hardware LPM.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When the link state changes, xHC will report a port status change event
and set the PORT_PLC bit, for both USB3 and USB2 root hub ports.

The PLC will be cleared by usbcore for USB3 root hub ports, but not for
USB2 ports, because they do not report USB_PORT_STAT_C_LINK_STATE in
wPortChange.

Clear it for USB2 root hub ports in handle_port_status().
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Introduce xhci_test_and_clear_bit() to clear RWC bit in PORTSC register.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Introduce xhci_set_link_state() to remove redundant codes.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Check device's LPM capability by examining the bmAttibutes field of the
USB2.0 Extension Descriptor.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This commit gets BOS(Binary Device Object Store) descriptor set for Super
Speed devices and High Speed devices which support BOS descriptor.

BOS descriptor is used to report additional USB device-level capabilities
that are not reported via the Device descriptor. By getting BOS descriptor
set, driver can check device's device-level capability such as LPM
capability.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NShaun Silk <g0del@bigpond.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This allow to clean duplicated code in most of SOC driver.
Signed-off-by: NMatthieu CASTET <castet.matthieu@free.fr>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>  # fixes 3.1 build error
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>