Adding the write bit and RC bits to pte permissions does not require a
pte clear and flush. There should not be other bits changed here,
because restricting access or changing the PFN must have already
invalidated any existing ptes (otherwise the race is already lost).
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

When the radix fault handler has no page from the process address
space (e.g., for IO memory), it looks up the process pte and sets
partition table pte using that to get attributes like CI and guarded.
If the process table entry is to be writable, set _PAGE_DIRTY as well
to avoid an RC update. If not, then ensure _PAGE_DIRTY does not come
across. Set _PAGE_ACCESSED as well to avoid RC update.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

The radix guest code can has fewer restrictions about what context it
can run in, so move this flushing out of assembly and have it use the
Linux TLB flush implementations introduced previously.

This allows powerpc:tlbie trace events to be used.

This changes the tlbiel sequence to only execute RIC=2 flush once on
the first set flushed, then RIC=0 for the rest of the sets. The end
result of the flush should be unchanged. This matches the local PID
flush pattern that was introduced in a5998fcb ("powerpc/mm/radix:
Optimise tlbiel flush all case").
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

This has the advantage of consolidating TLB flush code in fewer
places, and it also implements powerpc:tlbie trace events.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

When partition scope mappings are unmapped with kvm_unmap_radix, the
pte is cleared, but the page table structure is left in place. If the
next page fault requests a different page table geometry (e.g., due to
THP promotion or split), kvmppc_create_pte is responsible for changing
the page tables.

When a page table entry is to be converted to a large pte, the page
table entry is cleared, the PWC flushed, then the page table it points
to freed. This will cause pte page tables to leak when a 1GB page is
to replace a pud entry points to a pmd table with pte tables under it:
The pmd table will be freed, but its pte tables will be missed.

Fix this by replacing the simple clear and free code with one that
walks down the page tables and frees children. Care must be taken to
clear the root entry being unmapped then flushing the PWC before
freeing any page tables, as explained in comments.

This requires PWC flush to logically become a flush-all-PWC (which it
already is in hardware, but the KVM API needs to be changed to avoid
confusion).

This code also checks that no unexpected pte entries exist in any page
table being freed, and unmaps those and emits a WARN. This is an
expensive operation for the pte page level, but partition scope
changes are rare, so it's unconditional for now to iron out bugs. It
can be put under a CONFIG option or removed after some time.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

tlbies to an LPAR do not have to be serialised since POWER4/PPC970,
after which the MMU_FTR_LOCKLESS_TLBIE feature was introduced to
avoid tlbie locking.

Since commit c17b98cf ("KVM: PPC: Book3S HV: Remove code for
PPC970 processors"), KVM no longer supports processors that do not
have this feature, so the tlbie locking can be removed completely.
A sanity check for the feature is put in kvmppc_mmu_hv_init.

Testing was done on a POWER9 system in HPT mode, with a -smp 32 guest
in HPT mode. 32 instances of the powerpc fork benchmark from selftests
were run with --fork, and the results measured.

Without this patch, total throughput was about 13.5K/sec, and this is
the top of the host profile:

   74.52%  [k] do_tlbies
    2.95%  [k] kvmppc_book3s_hv_page_fault
    1.80%  [k] calc_checksum
    1.80%  [k] kvmppc_vcpu_run_hv
    1.49%  [k] kvmppc_run_core

After this patch, throughput was about 51K/sec, with this profile:

   21.28%  [k] do_tlbies
    5.26%  [k] kvmppc_run_core
    4.88%  [k] kvmppc_book3s_hv_page_fault
    3.30%  [k] _raw_spin_lock_irqsave
    3.25%  [k] gup_pgd_range
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

When KVM emulates VMX store, it will invoke kvmppc_get_vmx_data() to
retrieve VMX reg val. kvmppc_get_vmx_data() will check mmio_host_swabbed
to decide which double word of vr[] to be used. But the
mmio_host_swabbed can be uninitialized during VMX store procedure:

kvmppc_emulate_loadstore
	\- kvmppc_handle_store128_by2x64
		\- kvmppc_get_vmx_data

So vcpu->arch.mmio_host_swabbed is not meant to be used at all for
emulation of store instructions, and this patch makes that true for
VMX stores. This patch also initializes mmio_host_swabbed to avoid
possible future problems.
Signed-off-by: NSimon Guo <wei.guo.simon@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

This patch moves nip/ctr/lr/xer registers from scattered places in
kvm_vcpu_arch to pt_regs structure.

cr register is "unsigned long" in pt_regs and u32 in vcpu->arch.
It will need more consideration and may move in later patches.
Signed-off-by: NSimon Guo <wei.guo.simon@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

Current regs are scattered at kvm_vcpu_arch structure and it will
be more neat to organize them into pt_regs structure.

Also it will enable reimplementation of MMIO emulation code with
analyse_instr() later.
Signed-off-by: NSimon Guo <wei.guo.simon@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

This merges in the ppc-kvm topic branch of the powerpc repository
to get some changes on which future patches will depend, in particular
the definitions of various new TLB flushing functions.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

Use new return type vm_fault_t for fault handler
in struct vm_operations_struct. For now, this is
just documenting that the function returns a
VM_FAULT value rather than an errno.  Once all
instances are converted, vm_fault_t will become
a distinct type.

commit 1c8f4220 ("mm: change return type to
vm_fault_t")
Signed-off-by: NSouptick Joarder <jrdr.linux@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

Although it does not seem possible to break the host by passing bad
parameters when creating a TCE table in KVM, it is still better to get
an early clear indication of that than debugging weird effect this might
bring.

This adds some sanity checks that the page size is 4KB..16GB as this is
what the actual LoPAPR supports and that the window actually fits 64bit
space.
Signed-off-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: NBalbir Singh <bsingharora@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

At the moment we only support in the host the IOMMU page sizes which
the guest is aware of, which is 4KB/64KB/16MB. However P9 does not support
16MB IOMMU pages, 2MB and 1GB pages are supported instead. We can still
emulate bigger guest pages (for example 16MB) with smaller host pages
(4KB/64KB/2MB).

This allows the physical IOMMU pages to use a page size smaller or equal
than the guest visible IOMMU page size.
Signed-off-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

The other TCE handlers use page shift from the guest visible TCE table
(described by kvmppc_spapr_tce_iommu_table) so let's make H_STUFF_TCE
handlers do the same thing.

This should cause no behavioral change now but soon we will allow
the iommu_table::it_page_shift being different from from the emulated
table page size so this will play a role.
Signed-off-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Acked-by: NBalbir Singh <bsingharora@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

We now have interrupts hard-disabled when coming back from
kvmppc_hv_entry_trampoline, so this changes the comment to reflect
that.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

Although Linux doesn't use PURR and SPURR ((Scaled) Processor
Utilization of Resources Register), other OSes depend on them.
On POWER8 they count at a rate depending on whether the VCPU is
idle or running, the activity of the VCPU, and the value in the
RWMR (Region-Weighting Mode Register).  Hardware expects the
hypervisor to update the RWMR when a core is dispatched to reflect
the number of online VCPUs in the vcore.

This adds code to maintain a count in the vcore struct indicating
how many VCPUs are online.  In kvmppc_run_core we use that count
to set the RWMR register on POWER8.  If the core is split because
of a static or dynamic micro-threading mode, we use the value for
8 threads.  The RWMR value is not relevant when the host is
executing because Linux does not use the PURR or SPURR register,
so we don't bother saving and restoring the host value.

For the sake of old userspace which does not set the KVM_REG_PPC_ONLINE
register, we set online to 1 if it was 0 at the time of a KVM_RUN
ioctl.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

This adds a new KVM_REG_PPC_ONLINE register which userspace can set
to 0 or 1 via the GET/SET_ONE_REG interface to indicate whether it
considers the VCPU to be offline (0), that is, not currently running,
or online (1).  This will be used in a later patch to configure the
register which controls PURR and SPURR accumulation.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

A radix guest can execute tlbie instructions to invalidate TLB entries.
After a tlbie or a group of tlbies, it must then do the architected
sequence eieio; tlbsync; ptesync to ensure that the TLB invalidation
has been processed by all CPUs in the system before it can rely on
no CPU using any translation that it just invalidated.

In fact it is the ptesync which does the actual synchronization in
this sequence, and hardware has a requirement that the ptesync must
be executed on the same CPU thread as the tlbies which it is expected
to order.  Thus, if a vCPU gets moved from one physical CPU to
another after it has done some tlbies but before it can get to do the
ptesync, the ptesync will not have the desired effect when it is
executed on the second physical CPU.

To fix this, we do a ptesync in the exit path for radix guests.  If
there are any pending tlbies, this will wait for them to complete.
If there aren't, then ptesync will just do the same as sync.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

When a vcpu priority (CPPR) is set to a lower value (masking more
interrupts), we stop processing interrupts already in the queue
for the priorities that have now been masked.

If those interrupts were previously re-routed to a different
CPU, they might still be stuck until the older one that has
them in its queue processes them. In the case of guest CPU
unplug, that can be never.

To address that without creating additional overhead for
the normal interrupt processing path, this changes H_CPPR
handling so that when such a priority change occurs, we
scan the interrupt queue for that vCPU, and for any
interrupt in there that has been re-routed, we replace it
with a dummy and force a re-trigger.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

The current partition table unmap code clears the _PAGE_PRESENT bit
out of the pte, which leaves pud_huge/pmd_huge true and does not
clear pud_present/pmd_present.  This can confuse subsequent page
faults and possibly lead to the guest looping doing continual
hypervisor page faults.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

The standard eieio ; tlbsync ; ptesync must follow tlbie to ensure it
is ordered with respect to subsequent operations.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

Currently, the HV KVM guest entry/exit code adds the timebase offset
from the vcore struct to the timebase on guest entry, and subtracts
it on guest exit.  Which is fine, except that it is possible for
userspace to change the offset using the SET_ONE_REG interface while
the vcore is running, as there is only one timebase offset per vcore
but potentially multiple VCPUs in the vcore.  If that were to happen,
KVM would subtract a different offset on guest exit from that which
it had added on guest entry, leading to the timebase being out of sync
between cores in the host, which then leads to bad things happening
such as hangs and spurious watchdog timeouts.

To fix this, we add a new field 'tb_offset_applied' to the vcore struct
which stores the offset that is currently applied to the timebase.
This value is set from the vcore tb_offset field on guest entry, and
is what is subtracted from the timebase on guest exit.  Since it is
zero when the timebase offset is not applied, we can simplify the
logic in kvmhv_start_timing and kvmhv_accumulate_time.

In addition, we had secondary threads reading the timebase while
running concurrently with code on the primary thread which would
eventually add or subtract the timebase offset from the timebase.
This occurred while saving or restoring the DEC register value on
the secondary threads.  Although no specific incorrect behaviour has
been observed, this is a race which should be fixed.  To fix it, we
move the DEC saving code to just before we call kvmhv_commence_exit,
and the DEC restoring code to after the point where we have waited
for the primary thread to switch the MMU context and add the timebase
offset.  That way we are sure that the timebase contains the guest
timebase value in both cases.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

Directly use fault_in_pages_readable instead of manual __get_user code. Fix
warning treated as error with W=1:

  arch/powerpc/kernel/kvm.c:675:6: error: variable ‘tmp’ set but not used [-Werror=unused-but-set-variable]
Suggested-by: NChristophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: NMathieu Malaterre <malat@debian.org>
Reviewed-by: NChristophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Implement a local TLB flush for invalidating an LPID with variants for
process or partition scope. And a global TLB flush for invalidating
a partition scoped page of an LPID.

These will be used by KVM in subsequent patches.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In the next set of patches, we will switch pmd allocator to use page fragments
and the locking will be updated to split pmd ptlock. We want to avoid using
fragments for partition-scoped table. Use slab cache similar to level 4 table
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Pll KVM fixes from Radim Krčmář:
 "ARM:
   - Fix proxying of GICv2 CPU interface accesses
   - Fix crash when switching to BE
   - Track source vcpu git GICv2 SGIs
   - Fix an outdated bit of documentation

  x86:
   - Speed up injection of expired timers (for stable)"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86: remove APIC Timer periodic/oneshot spikes
  arm64: vgic-v2: Fix proxying of cpuif access
  KVM: arm/arm64: vgic_init: Cleanup reference to process_maintenance
  KVM: arm64: Fix order of vcpu_write_sys_reg() arguments
  KVM: arm/arm64: vgic: Fix source vcpu issues for GICv2 SGI

Pull iommu fixes from Joerg Roedel:

 - fix a compile warning in the AMD IOMMU driver with irq remapping
   disabled

 - fix for VT-d interrupt remapping and invalidation size (caused a
   BUG_ON when trying to invalidate more than 4GB)

 - build fix and a regression fix for broken graphics with old DTS for
   the rockchip iommu driver

 - a revert in the PCI window reservation code which fixes a regression
   with VFIO.

* tag 'iommu-fixes-v4.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu: rockchip: fix building without CONFIG_OF
  iommu/vt-d: Use WARN_ON_ONCE instead of BUG_ON in qi_flush_dev_iotlb()
  iommu/vt-d: fix shift-out-of-bounds in bug checking
  iommu/dma: Move PCI window region reservation back into dma specific path.
  iommu/rockchip: Make clock handling optional
  iommu/amd: Hide unused iommu_table_lock
  iommu/vt-d: Fix usage of force parameter in intel_ir_reconfigure_irte()

Pull x86 fix from Thomas Gleixner:
 "Unbreak the CPUID CPUID_8000_0008_EBX reload which got dropped when
  the evaluation of physical and virtual bits which uses the same CPUID
  leaf was moved out of get_cpu_cap()"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpu: Restore CPUID_8000_0008_EBX reload

Pull clocksource fixes from Thomas Gleixner:
 "The recent addition of the early TSC clocksource breaks on machines
  which have an unstable TSC because in case that TSC is disabled, then
  the clocksource selection logic falls back to the early TSC which is
  obviously bogus.

  That also unearthed a few robustness issues in the clocksource
  derating code which are addressed as well"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource: Rework stale comment
  clocksource: Consistent de-rate when marking unstable
  x86/tsc: Fix mark_tsc_unstable()
  clocksource: Initialize cs->wd_list
  clocksource: Allow clocksource_mark_unstable() on unregistered clocksources
  x86/tsc: Always unregister clocksource_tsc_early

Pull irq fix from Thomas Gleixner:
 "A single fix to prevent false positives in the spurious interrupt
  detector when more than a single demultiplex register is evaluated in
  the Qualcom irq combiner driver"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/qcom: Fix check for spurious interrupts

Pull x86 platform driver fixes from Darren Hart:

 - We missed a case in the Dell config dependencies resulting in a
   possible bad configuration, resolve it by giving up on trying to keep
   DELL_LAPTOP visible in the menu and make it depend on DELL_SMBIOS.

 - Fix a null pointer dereference at module unload for the asus-wireless
   driver.

* tag 'platform-drivers-x86-v4.17-2' of git://git.infradead.org/linux-platform-drivers-x86:
  platform/x86: Kconfig: Fix dell-laptop dependency chain.
  platform/x86: asus-wireless: Fix NULL pointer dereference

Pull USB fixes from Greg KH:
 "Here are some USB driver fixes for 4.17-rc4.

  The majority of them are some USB gadget fixes that missed my last
  pull request. The "largest" patch in here is a fix for the old visor
  driver that syzbot found 6 months or so ago and I finally remembered
  to fix it.

  All of these have been in linux-next with no reported issues"

* tag 'usb-4.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  Revert "usb: host: ehci: Use dma_pool_zalloc()"
  usb: typec: tps6598x: handle block reads separately with plain-I2C adapters
  usb: typec: tcpm: Release the role mux when exiting
  USB: Accept bulk endpoints with 1024-byte maxpacket
  xhci: Fix use-after-free in xhci_free_virt_device
  USB: serial: visor: handle potential invalid device configuration
  USB: serial: option: adding support for ublox R410M
  usb: musb: trace: fix NULL pointer dereference in musb_g_tx()
  usb: musb: host: fix potential NULL pointer dereference
  usb: gadget: composite Allow for larger configuration descriptors
  usb: dwc3: gadget: Fix list_del corruption in dwc3_ep_dequeue
  usb: dwc3: gadget: dwc3_gadget_del_and_unmap_request() can be static
  usb: dwc2: pci: Fix error return code in dwc2_pci_probe()
  usb: dwc2: WA for Full speed ISOC IN in DDMA mode.
  usb: dwc2: dwc2_vbus_supply_init: fix error check
  usb: gadget: f_phonet: fix pn_net_xmit()'s return type

Since the commit "8003c9ae: add APIC Timer periodic/oneshot mode VMX
preemption timer support", a Windows 10 guest has some erratic timer
spikes.

Here the results on a 150000 times 1ms timer without any load:
	  Before 8003c9ae | After 8003c9ae
Max           1834us          |  86000us
Mean          1100us          |   1021us
Deviation       59us          |    149us
Here the results on a 150000 times 1ms timer with a cpu-z stress test:
	  Before 8003c9ae | After 8003c9ae
Max          32000us          | 140000us
Mean          1006us          |   1997us
Deviation      140us          |  11095us

The root cause of the problem is starting hrtimer with an expiry time
already in the past can take more than 20 milliseconds to trigger the
timer function.  It can be solved by forward such past timers
immediately, rather than submitting them to hrtimer_start().
In case the timer is periodic, update the target expiration and call
hrtimer_start with it.

v2: Check if the tsc deadline is already expired. Thank you Mika.
v3: Execute the past timers immediately rather than submitting them to
hrtimer_start().
v4: Rearm the periodic timer with advance_periodic_target_expiration() a
simpler version of set_target_expiration(). Thank you Paolo.

Cc: Mika Penttilä <mika.penttila@nextfour.com>
Cc: Wanpeng Li <kernellwp@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: NAnthoine Bourgeois <anthoine.bourgeois@blade-group.com>
8003c9ae ("KVM: LAPIC: add APIC Timer periodic/oneshot mode VMX preemption timer support")
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

KVM/arm fixes for 4.17, take #2

- Fix proxying of GICv2 CPU interface accesses
- Fix crash when switching to BE
- Track source vcpu git GICv2 SGIs
- Fix an outdated bit of documentation

Merge tag 'kbuild-fixes-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - remove state comment in modpost

 - extend MAINTAINERS entry to cover modpost and more makefiles

 - fix missed building of SANCOV gcc-plugin

 - replace left-over 'bison' with $(YACC)

 - display short log when generating parer of genksyms

* tag 'kbuild-fixes-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  genksyms: fix typo in parse.tab.{c,h} generation rules
  kbuild: replace hardcoded bison in cmd_bison_h with $(YACC)
  gcc-plugins: fix build condition of SANCOV plugin
  MAINTAINERS: Update Kbuild entry with a few paths
  modpost: delete stale comment

Pull clk fixes froom Stephen Boyd:
 "A handful of fixes for the stm32mp1 clk driver came in during the
  merge window for the driver that got merged in the merge window.

  Plus a warning fix for unused PM ops and a couple fixes for the meson
  clk driver clk names that went unnoticed with the regmap rework.

  There's also another fix in here for the mux rounding flag which
  wasn't doing what it said it did, but now it does"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: meson: meson8b: fix meson8b_cpu_clk parent clock name
  clk: meson: meson8b: fix meson8b_fclk_div3_div clock name
  clk: meson: drop meson_aoclk_gate_regmap_ops
  clk: meson: honor CLK_MUX_ROUND_CLOSEST in clk_regmap
  clk: honor CLK_MUX_ROUND_CLOSEST in generic clk mux
  clk: cs2000: mark resume function as __maybe_unused
  clk: stm32mp1: remove ck_apb_dbg clock
  clk: stm32mp1: set stgen_k clock as critical
  clk: stm32mp1: add missing tzc2 clock
  clk: stm32mp1: fix SAI3 & SAI4 clocks
  clk: stm32mp1: remove unused dfsdm_src[] const
  clk: stm32mp1: add missing static

Pull remoteproc and rpmsg fixes from Bjorn Andersson:

 - fix screw-up when reversing boolean for rproc_stop()

 - add missing OF node refcounting dereferences

 - add missing MODULE_ALIAS in rpmsg_char

* tag 'rproc-v4.17-1' of git://github.com/andersson/remoteproc:
  rpmsg: added MODULE_ALIAS for rpmsg_char
  remoteproc: qcom: Fix potential device node leaks
  remoteproc: fix crashed parameter logic on stop call

Pull drm fixes from Dave Airlie:
 "vmwgfx, i915, vc4, vga dac fixes.

  This seems eerily quiet, so I expect it will explode next week or
  something.

  One i915 model firmware, two vmwgfx fixes, one vc4 fix and one bridge
  leak fix"

* tag 'drm-fixes-for-v4.17-rc4' of git://people.freedesktop.org/~airlied/linux:
  drm/bridge: vga-dac: Fix edid memory leak
  drm/vc4: Make sure vc4_bo_{inc,dec}_usecnt() calls are balanced
  drm/i915/glk: Add MODULE_FIRMWARE for Geminilake
  drm/vmwgfx: Fix a buffer object leak
  drm/vmwgfx: Clean up fbdev modeset locking