Enable a firmware option that appears to be necessary for reliable
operation.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Printing anything over netconsole before hw is up and running is,
of course, not going to work.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

with current kernels, tulip 21142 ethernet controllers fail to connect
to a 10Mbps only (i.e. without negotiation-partner) network.  It used
to work in 2.4 kernels.  Fix that.  Tested on a 21142 Rev 0x11.
Signed-off-by: NPhilippe De Muyter <phdm@macqel.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix inverted logic
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 0f0ca340 ("phy: power
management support") caused a regression in the gianfar driver.

Now phylib turns off PHY power during suspend, and thus WOL
doesn't work anymore.

This patch workarounds the issue by enabling wakeup in the MDIO
device, i.e. just restores the old behaviour for the gianfar
driver. Note that this way all PHYs on a given MDIO bus won't
be turned off during suspend, which isn't good from the power
saving point of view.

A proper, per netdevice wakeup management support will need
a bit reworked phylib suspend/resume logic.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With a postfix decrement the timeout will reach -1 rather than 0,
so the warning will not be issued.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

smsc9420 performs an interrupt signalling test when the interface is
brought up.  The current code mistakenly sets its test flag to false
AFTER enabling the software interrupt source, making failure quite
likely.

This patch changes the code to set the test flag BEFORE enabling
interrupts. I've also removed an smp_wmb because the following spinlock
provides an implicit memory barrier.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit b31a1d8b ("gianfar: Convert
gianfar to an of_platform_driver") changes the gianfar's phy id to the
format like "mdio@xxxx:xx", but uec still uses the old format like
"xxxxxxxx:xx".  For the board whose UEC uses gianfar-mdio like
MPC8568MDS, the phy can not be attached because of the incompatible
phy id format. This patch changes uec's phy id to the same format as
gianfar's.
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As reported by Toralf Förster and Randy Dunlap.

- http://linuxwimax.org/pipermail/wimax/2009-January/000460.html

- http://lkml.org/lkml/2009/1/29/279

The definitions needed for the wimax stack and i2400m driver debug
infrastructure was, by mistake, compiled depending on CONFIG_DEBUG_FS
(by them being placed in the debugfs.c files); thus the build broke in
2.6.29-rc3 when debugging was enabled (CONFIG_WIMAX_DEBUG) and
DEBUG_FS was disabled.

These definitions are always needed if debug is enabled at compile
time (independently of DEBUG_FS being or not enabled), so moving them
to a file that is always compiled fixes the issue.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For kernel bugzilla #12537:
http://bugzilla.kernel.org/show_bug.cgi?id=12537

Free memory.
Signed-off-by: NDaniel Marjamäki <danielm77@spray.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based upon a report from Michael Tokarev <mjt@tls.msk.ru>:

	Just saw in dmesg:

	ioctl32(kvm:4408): Unknown cmd fd(9) cmd(800454cf){t:'T';sz:4} arg(ffc668e4) on /dev/net/tun
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBenjamin Zores <benjamin.zores@alcatel-lucent.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This documentation is old.  Add a short note to describe why aliases
are no long necessary, and remove the old contact/edit info.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It oopsd for me in skb_seq_read. addr2line said it was
linux-2.6/net/core/skbuff.c:2228, which is this line:


	while (st->frag_idx < skb_shinfo(st->cur_skb)->nr_frags) {


I added some printks in there and it looks like we hit this:

        } else if (st->root_skb == st->cur_skb &&
                   skb_shinfo(st->root_skb)->frag_list) {
                 st->cur_skb = skb_shinfo(st->root_skb)->frag_list;
                 st->frag_idx = 0;
                 goto next_skb;
        }



Actually I did some testing and added a few printks and found that the
st->cur_skb->data was 0 and hence the ptr used by iscsi_tcp was null.
This caused the kernel panic.

 	if (abs_offset < block_limit) {
-		*data = st->cur_skb->data + abs_offset;
+		*data = st->cur_skb->data + (abs_offset - st->stepped_offset);

I enabled the debug_tcp and with a few printks found that the code did
not go to the next_skb label and could find that the sequence being
followed was this -

It hit this if condition -

        if (st->cur_skb->next) {
                st->cur_skb = st->cur_skb->next;
                st->frag_idx = 0;
                goto next_skb;

And so, now the st pointer is shifted to the next skb whereas actually
it should have hit the second else if first since the data is in the
frag_list.

        else if (st->root_skb == st->cur_skb &&
                 skb_shinfo(st->root_skb)->frag_list) {
                st->cur_skb = skb_shinfo(st->root_skb)->frag_list;
                goto next_skb;
        }

Reversing the two conditions the attached patch fixes the issue for me
on top of Herbert's patches. 
Signed-off-by: NShyam Iyer <shyam_iyer@dell.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The frag_list handling was broken in skb_seq_read:

1) We didn't add the stepped offset when looking at the head
are of fragments other than the first.

2) We didn't take the stepped offset away when setting the data
pointer in the head area.

3) The frag index wasn't reset.

This patch fixes both issues.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reducing jumbo ring size below 1024 reduces throughput for old
firmwares (3.4.216 and older) running on older (NX2031) chip,
so restore it back to 1024.

This was reduced in commit 32ec8033
("netxen: reduce memory footprint").

Raising jumbo ring size from 512 to 1024, adds ~4MB per port, but
there's still big saving because of original patch (~20MB per port).
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ath5k_config updates the software context without taking sc->lock.

Changes-licensed-under: 3-Clause-BSD
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When CONFIG_CFG80211_REG_DEBUG is enabled and an intersection
occurs we are printing the regulatory domain passed by CRDA
and indicating its the intersected regulatory domain. Lets fix
this and print the intersection as originally intended.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes two issues with the sanity check loop when processing
the country IE:

1. Do not use frequency for the current subband channel check,
   this was a big fat typo.
2. Apply the 5 GHz 4-channel steps when considering max channel
   on each subband as was done with a recent patch.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch fixes memcpy to NULL address when the ucode DMA allocation failure.

This is a fix to bug
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1861Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After reports of poor performance, a review of the latest vendor driver
(rtl8187_linux_26.1025.0328.2007) for RTL8187L devices was undertaken.

A difference was found in the code used to index the OFDM power tables. When
the Linux driver was changed, my unit works at a much greater range than
before. I think this fixes Bugzilla #12380 and has been tested by at least
two other users.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NMartín Ernesto Barreyro <barreyromartin@gmail.com>
Cc: Stable <stable@kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

His email address keeps bouncing, and he's not interested in mac80211
patches etc. anyway.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The kernel manages this value internally, as necessary, as
VIFs are added/removed and as multicast routers are registered
and deregistered.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch addresses the IPv6 multicast routing issues described
below.  It was tested with XORP 1.4/1.5 as the IPv6 PIM-SM routing
daemon against FreeBSD peers.

net/ipv6/ip6_input.c:

  - Don't try to forward link-local multicast packets.

  - Don't reset skb2->dev before calling ip6_mr_input() so packets can
    be identified as coming from the PIM register vif properly.

net/ipv6/ip6mr.c:

  - Fix incoming PIM register messages processing:

    * The IPv6 pseudo-header should be included when checksumming PIM
      messages (RFC 4601 section 4.9; RFC 3973 section 4.7.1).

    * Packets decapsulated from PIM register messages should have
      skb->protocol ETH_P_IPV6.

  - Enable/disable IPv6 multicast forwarding on the corresponding
    interface when a routing daemon adds/removes a multicast virtual
    interface.

  - Remove incorrect skb_pull() to fix userspace signaling.

  - Enable/disable global IPv6 multicast forwarding when an IPv6
    multicast routing socket is opened/closed.

net/ipv6/route.c:

  - Don't use strict routing logic for packets decapsulated from PIM
    register messages (similar to disabling rp_filter for the IPv4
    case).
Signed-off-by: NThomas Goff <thomas.goff@boeing.com>
Reviewed-by: NFred Templin <fred.l.templin@boeing.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the xfrm reverse flow lookup for icmp6 so that icmp6 packets
don't get lost over ipsec tunnels. Similar patch is in RHEL5 kernel for a quite
long time and I do not see why it isn't in mainline.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 9db66bdc (net: convert
TCP/DCCP ehash rwlocks to spinlocks), I forgot to change one
occurrence of rwlock_t to spinlock_t

I believe sizeof(raw_spinlock_t) might be > 0 on !CONFIG_SMP if
CONFIG_DEBUG_SPINLOCK while sizeof(raw_rwlock_t) should be 0 in this
case.

Fortunatly, CONFIG_DEBUG_SPINLOCK adds fields to both spinlock_t and
rwlock_t, but at this might change in the future (being able to debug
spinlocks but not rwlocks for example), better to be safe.
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A nasty bug was found where an MTU change (or anything else that caused a
reset) could race with the interrupt code.  The interrupt code was entered
by a shared interrupt during the MTU change.

This change prevents the interrupt code from running while the driver is in
the middle of its reset path.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tcp_splice_data_recv has two lengths to consider: the len parameter it
gets from tcp_read_sock, which specifies the amount of data in the skb,
and rd_desc->count, which is the amount of data the splice caller still
wants.  Currently it passes just the latter to skb_splice_bits, which then
splices min(rd_desc->count, skb->len - offset) bytes.

Most of the time this is fine, except when the skb contains urgent data.
In that case len goes only up to the urgent byte and is less than
skb->len - offset.  By ignoring len tcp_splice_data_recv may a) splice
data tcp_read_sock told it not to, b) return to tcp_read_sock a value > len.

Now, tcp_read_sock doesn't handle used > len and leaves the socket in a
bad state (both sk_receive_queue and copied_seq are bad at that point)
resulting in duplicated data and corruption.

Fix by passing min(rd_desc->count, len) to skb_splice_bits.
Signed-off-by: NDimitris Michailidis <dm@chelsio.com>
Acked-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/r6040.c:441: warning: unused variable 'pdev'
Signed-off-by: NManish Katiyar <mkatiyar@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 9088c560
(udp: Improve port randomization) introduced a regression for UDP bind() syscall
to null port (getting a random port) in case lot of ports are already in use.

This is because we do about 28000 scans of very long chains (220 sockets per chain),
with many spin_lock_bh()/spin_unlock_bh() calls.

Fix this using a bitmap (64 bytes for current value of UDP_HTABLE_SIZE)
so that we scan chains at most once.

Instead of 250 ms per bind() call, we get after patch a time of 2.9 ms 

Based on a report from Vitaly Mayatskikh
Reported-by: NVitaly Mayatskikh <v.mayatskih@gmail.com>
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Tested-by: NVitaly Mayatskikh <v.mayatskih@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without this fix, virtio_net makes incorrect usage of scatterlists. It sets
the end of the scatterlist chain after the first element, despite the fact
that more entries come after it.

If you try to run dma_map_sg() on one of the scatterlists given to you by
add_buf(), you will get a null pointer oops.
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* master.kernel.org:/home/rmk/linux-2.6-arm: (22 commits)
  [ARM] fix section-based ioremap
  [NET] am79c961a: fix spin_lock usage
  [ARM] omap: usb: thou shalt not provide empty release functions
  [ARM] omap: watchdog: allow OMAP watchdog driver on OMAP34xx platforms
  [ARM] 5369/1: omap mmc: Add new omap hsmmc controller for 2430 and 34xx, v3
  [ARM] clkdev: fix clock matching
  [ARM] 5370/1: at91: fix rm9200 watchdog
  [ARM] 5368/1: arch/arm/mach-davinci/usb.c buildfix
  [ARM] 5365/1: s3cmci: Use new include path of dma.h
  [ARM] fix StrongARM-11x0 page copy implementation
  [ARM] omap: ensure OMAP drivers pass a struct device to clk_get()
  ARM: OMAP: Fix compile for h3 MMC
  ARM: OMAP: Remove unused platform devices, v3
  ARM: OMAP: Fix ASoC by enabling writes to XCCR and RCCR McBSP registers, v3
  ARM: OMAP: Fix OSK ASoC by registering I2C board info for tlvaic23
  ARM: OMAP: remove duplicated #include's
  ARM: OMAP: Fix DMA CCR programming for request line > 63, v3
  ARM: OMAP: Fix gpio.c compile on 15xx with CONFIG_DEBUGFS
  ARM: OMAP: Fix compile for beagle
  ARM: OMAP: Fix gpio by switching to generic gpio calls, v2
  ...

* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  i2c: Warn on deprecated binding model use
  eeprom: More consistent symbol names
  eeprom: Move 93cx6 eeprom driver to /drivers/misc/eeprom
  spi: Move at25 (for SPI eeproms) to /drivers/misc/eeprom
  i2c: Move old eeprom driver to /drivers/misc/eeprom
  i2c: Move at24 to drivers/misc/eeprom
  i2c: Quilt tree has moved
  i2c: Delete many unused adapter IDs
  i2c: Delete 10 unused driver IDs

* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
  kbuild: fix kbuild.txt typos
  kbuild: print usage with no arguments in scripts/config
  Revert "kbuild: strip generated symbols from *.ko"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (92 commits)
  gianfar: Revive VLAN support
  vlan: Export symbols as non GPL symbols.
  bnx2x: tx_has_work should not wait for FW
  netxen: reduce memory footprint
  netxen: fix vlan tso/checksum offload
  net: Fix linux/if_frad.h's suitability for userspace.
  net: Move config NET_NS to from net/Kconfig to init/Kconfig
  isdn: Fix missing ifdef in isdn_ppp
  networking: document "nc" in addition to "netcat" in netconsole.txt
  e1000e: workaround hw errata
  af_key: initialize xfrm encap_oa
  virtio_net: Fix MAX_PACKET_LEN to support 802.1Q VLANs
  lcs: fix compilation for !CONFIG_IP_MULTICAST
  rtl8187: Add termination packet to prevent stall
  iwlwifi: fix rs_get_rate WARN_ON()
  p54usb: fix packet loss with first generation devices
  sctp: Fix another socket race during accept/peeloff
  sctp: Properly timestamp outgoing data chunks for rtx purposes
  sctp: Correctly start rtx timer on new packet transmissions.
  sctp: Fix crc32c calculations on big-endian arhes.
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Fix DAX handling via userspace access from kernel.
  sparc64: Annotate sparc64 specific syscalls with SYSCALL_DEFINEx()
  [CVE-2009-0029] sparc: Enable syscall wrappers for 64-bit
  sparc64: Initialize FHC/CLOCK LED platform_device 'id' field correctly.
  sparc64: fix modpost failure
  sparc64: fix readout of cpu/fpu type

commit 77ecaf2d ("gianfar: Fix VLAN
HW feature related frame/buffer size calculation") wrongly removed
priv->vlgrp assignment, and now priv->vlgrp is always NULL.

This patch fixes the issue, plus fixes following sparse warning
introduced by the same commit:
gianfar.c:1406:13: warning: context imbalance in 'gfar_vlan_rx_register' - wrong count at exit

gfar_vlan_rx_register() checks for "if (old_grp == grp)" and tries
to return w/o dropping the lock.

According to net/8021q/vlan.c VLAN core issues rx_register() callback:
1. In register_vlan_dev() only on a newly created group;
2. In unregister_vlan_dev() only if the group becomes empty.

Thus the check in the gianfar driver isn't needed.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In previous kernels, any kernel module could get access to the
'real-device' and the VLAN-ID for a particular VLAN.  In more recent
kernels, the code was restructured such that this is hard to do
without accessing private .h files for any module that cannot use
GPL-only symbols.

Attached is a patch to once again allow non-GPL modules the ability to
access the real-device and VLAN id for VLANs.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Acked-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current tx_has_work waited until all packets sent by the driver
are marked as completed by the FW. This is too greedy and it causes
the bnx2x_poll to spin in vain. The driver should only check that all
packets FW already completed are freed - only in unload flow the
driver should make sure that transmit queue is empty
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>