This fixes a problem caused by the overlap of the connection-setup and
established-state phases of DCCP connections.

During connection setup, the client retransmits Confirm Feature-Negotiation
options until a response from the server signals that it can move from the
half-established PARTOPEN into the OPEN state, whereupon the connection is
fully established on both ends (RFC 4340, 8.1.5).

However, since the client may already send data while it is in the PARTOPEN
state, consequences arise for the Maximum Packet Size: the problem is that the
initial option overhead is much higher than for the subsequent established
phase, as it involves potentially many variable-length list-type options
(server-priority options, RFC 4340, 6.4).

Applying the standard MPS is insufficient here: especially with larger
payloads this can lead to annoying, counter-intuitive EMSGSIZE errors.

On the other hand, reducing the MPS available for the established phase by
the added initial overhead is highly wasteful and inefficient.

The solution chosen therefore is a two-phase strategy:

   If the payload length of the DataAck in PARTOPEN is too large, an Ack is sent
   to carry the options, and the feature-negotiation list is then flushed.

   This means that the server gets two Acks for one Response. If both Acks get
   lost, it is probably better to restart the connection anyway and devising yet
   another special-case does not seem worth the extra complexity.

The result is a higher utilisation of the available packet space for the data
transmission phase (established state) of a connection.

The patch (over-)estimates the initial overhead to be 32*4 bytes -- commonly
seen values were around 90 bytes for initial feature-negotiation options.

It uses sizeof(u32) to mean "aligned units of 4 bytes".
For consistency, another use of 4-byte alignment is adapted.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch resolves a long-standing FIXME to dynamically update the Maximum
Packet Size depending on actual options usage.

It uses the flags set by the feature-negotiation infrastructure to compute
the required header option size.

Most options are fixed-size, a notable exception are Ack Vectors (required
currently only by CCID-2). These can have any length between 3 and 1020
bytes. As a result of testing, 16 bytes (2 bytes for type/length plus 14 Ack
Vector cells) have been found to be sufficient for loss-free situations.

There are currently no CCID-specific header options which may appear on data
packets, thus it is not necessary to define a corresponding CCID field as
suggested in the old comment.

Further changes:
----------------
 Adjusted the type of 'cur_mps' to match the unsigned return type of the
 function.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: NIan McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I guess these fields were one day 16-bit in the struct but
nowadays they're just using 8 bits anyway.

This is just a precaution, didn't result any change in my
case but who knows what all those varying gcc versions &
options do. I've been told that 16-bit is not so nice with
some cpus.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

copied was assigned zero right before the goto, so if (copied)
cannot ever be true.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also fixes insignificant bug that would cause sending of stale
SACK block (would occur in some corner cases).
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It seems that implementation in yeah was inconsistent to what
other did as it would increase cwnd one ack earlier than the
others do.

Size benefits:

  bictcp_cong_avoid |  -36
  tcp_cong_avoid_ai |  +52
  bictcp_cong_avoid |  -34
  tcp_scalable_cong_avoid |  -36
  tcp_veno_cong_avoid |  -12
  tcp_yeah_cong_avoid |  -38

= -104 bytes total
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similar to what is done elsewhere in TCP code when double
state checks are being done.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Redundant checks made indentation impossible to follow.
However, it might be useful to make this ca_state+is_sack
indexed array.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some comment about its current state added. So far I have
seen very few cases where the thing is actually useful,
usually just marginally (though admittedly I don't usually
see top of window losses where it seems possible that there
could be some gain), instead, more often the cases suffer
from L-marking spike which is certainly not desirable
(I'll bury improving it to my todo list, but on a low
prio position).
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Arnd Hannemann <hannemann@nets.rwth-aachen.de> noticed and was
puzzled by the fact that !tcp_is_fack(tp) leads to early return
near the beginning and the later on tcp_is_fack(tp) was still
used in an if condition. The later check was a left-over from
RFC3517 SACK stuff (== !tcp_is_fack(tp) behavior nowadays) as
there wasn't clear way how to handle this particular check
cheaply in the spirit of RFC3517 (using only SACK blocks, not
holes + SACK blocks as with FACK). I sort of left it there as
a reminder but since it's confusing other people just remove
it and comment the missing-feature stuff instead.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Arnd Hannemann <hannemann@nets.rwth-aachen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If cur_mss grew very recently so that the previously G/TSOed skb
now fits well into a single segment it would get send up in
parts unless we calculate # of segments again. This corner-case
could happen eg. after mtu probe completes or less than
previously sack blocks are required for the opposite direction.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1) We didn't remove any skbs, so no need to handle stale refs.

2) scoreboard_skb_hint is trivial, no timestamps were changed
   so no need to clear that one

3) lost_skb_hint needs tweaking similar to that of
   tcp_sacktag_one().
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If skb can be sent right away, we certainly should do that
if it's in the middle of the queue because it won't get
more data into it.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is possible that lost_cnt_hint gets underflow in
tcp_clean_rtx_queue because the cumulative ACK can cover
the segment where lost_skb_hint points to only partially,
which means that the hint is not cleared, opposite to what
my (earlier) comment claimed.

Also I don't agree what I ended up writing about non-trivial
case there to be what I intented to say. It was not supposed
to happen that the hint won't get cleared and we underflow
in any scenario.

In general, this is quite hard to trigger in practice.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Backtracking to sacked skbs is a horrible performance killer
since the hint cannot be advanced successfully past them...
...And it's totally unnecessary too.

In theory this is 2.6.27..28 regression but I doubt anybody
can make .28 to have worse performance because of other TCP
improvements.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

From: Guo-Fu Tseng <cooldavid@cooldavid.org>

Advance version number after previous changes.
Sorry for not come along with previous patch series.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Noticed by David Dillow.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As reported by Stephen Rothwell.

> Today's linux-next build (powerpc allyesconfig) failed like this:
>
> net/rds/cong.c: In function 'rds_cong_set_bit':
> net/rds/cong.c:284: error: implicit declaration of function 'generic___set_le_bit'
> net/rds/cong.c: In function 'rds_cong_clear_bit':
> net/rds/cong.c:298: error: implicit declaration of function 'generic___clear_le_bit'
> net/rds/cong.c: In function 'rds_cong_test_bit':
> net/rds/cong.c:309: error: implicit declaration of function 'generic_test_le_bit'
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/wireless/iwlwifi/iwl-tx.c
	net/8021q/vlan_core.c
	net/core/dev.c

The Motorola MOTOMAGX phones (Z6, E8, Zn5 so far) are providing
combined ACM/BLAN USB configuration. Since it has Vendor Specific
class, the corresponding drivers (cdc-acm, zaurus) can't find it just
by interface info. This patch adds usb id so the zaurus driver can
properly handle this combined device.
Signed-off-by: NDmitriy Taychenachev <dimichxp@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make usbnet_get_link() fall back to ethtool_op_get_link() instead of
defaulting to 1.  
     
This makes usbnet_get_link return valid results without the need for a
driver specific check_connect or mii ops as long as the driver calls
netif_carrier_{on,off}() as appropriate.  cdc_ether is an example of
such a driver.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current implementation of carrier detect in veth is broken.
It reports the link is down until both sides of the veth pair
are administatively up and then forever after it reports link up.

So fix veth so that it only reports link up when both interfaces
of the pair are administratively up.
Signed-off-by: NEric Biederman <ebiederm@aristanetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Ericsson F3507g wireless broadband module provides a CDC Ethernet
compliant interface, but identifies it as a "Mobile Direct Line" CDC
subclass, thereby preventing the CDC Ethernet class driver from picking
it up.  This patch adds the device id to cdc_ether.c as a workaround.

Ericsson has provided a "class" driver for this device:
http://kerneltrap.org/mailarchive/linux-net/2008/10/28/3832094
But closer inspection of that driver reveals that it adds little more
than duplication of code from cdc_ether.c.  See also
http://marc.info/?l=linux-usb&m=123334979706403&w=2Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All JMC250 chips have no problem with higher bits support.
Adding it back.
Found-by: NEthan Hsiao <ethanhsiao@jmicron.com>
Signed-off-by: NGuo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clear all modified GHC register flags.
Fixed-by: NEthan Hsiao <ethanhsiao@jmicron.com>
Signed-off-by: NGuo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should sync ring descriptor to pci device after modifying it.
Signed-off-by: NGuo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch modifies messages to display correct hardware version.
Signed-off-by: NGuo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is 2nd attempt to implement the initialization/reading of MAC address
from EEPROM. The first used PCI's VPD and there were some problems, some
devices are not able to read EEPROM content by VPD. The 2nd one uses direct
access to EEPROM through bit-banging interface and my testing results seem
to be much better.

I tested 5 systems each with different Realtek NICs and I didn't find any
problem. AFAIK Francois's NICs also works fine.

Original description:
This fixes the problem when MAC address is set by ifconfig or by
ip link commands and this address is stored in the device after
reboot. The power-off is needed to get right MAC address.
This is problem when Xen daemon is running because it renames the device
name from ethX to pethX and sets its MAC address to FE:FF:FF:FF:FF:FF.
After reboot the device is still using FE:FF:FF:FF:FF:FF.
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

'pap' is never used in ixgbe_dcb_hw_config_82599()
and 'eec' in ixgbe_acquire_eeptom() is only used when
status == 0 but GCC has some trouble seeing that.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

request_firmware() gives vmalloc'd memory, which is not suitable
for pci_map_single() and friends.

Use a kmalloc()'d copy of the firmware for this DMA operation.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the hardware-specific code in place, add all supported device id's,
along with base driver changes to enable 82599 devices.  The devices
being enabled are:

8086:10f7: 82599EB 10 Gigabit KX4 Network Connection
8086:10fb: 82599EB 10 Gigabit Network Connection

The device 8086:10fb is a fully-pluggable SFP+ NIC.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the DCB (Data Center Bridging) support for 82599 hardware.
This is similar to how the 82598 DCB code works.

This patch also removes the BCN (Backwards Congestion Notification) netlink
configuration code from the driver.  BCN was a pre-standard congestion
notification framework, and was not what the IEEE body decided upon for
standard congestion management. QCN (802.1Qau), Quantized Congestion
Notification is the accepted standard, which is not supported by 82599,
hence we remove the support altogether.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the hardware initialization code specific to 82599.  This
is similar to the 82598 hardware initialization code.  It also includes all
changes to the existing hardware init code to support 82599.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's conflicting assumptions in shifting, the caller assumes
that dupsack results in S'ed skbs (or a part of it) for sure but
never gave a hint to tcp_sacktag_one when dsack is actually in
use. Thus DSACK retrans_out -= pcount was not taken and the
counter became out of sync. Remove obstacle from that information
flow to get DSACKs accounted in tcp_sacktag_one as expected.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Tested-by: NDenys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The DCB netlink interface is required for building the userspace tools
available at e1000.sourceforge.net
Signed-off-by: NChris Leech <christopher.leech@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1) add an include for <linux/types.h>
2) change dcbmsg.dcb_family from unsigned char to __u8 to be more
   consistent with use of kernel types
Signed-off-by: NChris Leech <christopher.leech@intel.com>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The netpoll entry checks are required to ensure that we don't
receive normal packets when invoked via netpoll.  Unfortunately
it only ever worked for the netif_receive_skb/netif_rx entry
points.  The VLAN (and subsequently GRO) entry point didn't
have the check and therefore can trigger all sorts of weird
problems.

This patch adds the netpoll check to all entry points.

I'm still uneasy with receiving at all under netpoll (which
apparently is only used by the out-of-tree kdump code).  The
reason is it is perfectly legal to receive all data including
headers into highmem if netpoll is off, but if you try to do
that with netpoll on and someone gets a printk in an IRQ handler                                             
you're going to get a nice BUG_ON.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>