- 02 4月, 2020 2 次提交
-
-
由 Jarod Wilson 提交于
Bonding slave and team port devices should not have link-local addresses automatically added to them, as it can interfere with openvswitch being able to properly add tc ingress. Basic reproducer, courtesy of Marcelo: $ ip link add name bond0 type bond $ ip link set dev ens2f0np0 master bond0 $ ip link set dev ens2f1np2 master bond0 $ ip link set dev bond0 up $ ip a s 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: ens2f0np0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc mq master bond0 state UP group default qlen 1000 link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff 5: ens2f1np2: <NO-CARRIER,BROADCAST,MULTICAST,SLAVE,UP> mtu 1500 qdisc mq master bond0 state DOWN group default qlen 1000 link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff 11: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000 link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff inet6 fe80::20f:53ff:fe2f:ea40/64 scope link valid_lft forever preferred_lft forever (above trimmed to relevant entries, obviously) $ sysctl net.ipv6.conf.ens2f0np0.addr_gen_mode=0 net.ipv6.conf.ens2f0np0.addr_gen_mode = 0 $ sysctl net.ipv6.conf.ens2f1np2.addr_gen_mode=0 net.ipv6.conf.ens2f1np2.addr_gen_mode = 0 $ ip a l ens2f0np0 2: ens2f0np0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc mq master bond0 state UP group default qlen 1000 link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff inet6 fe80::20f:53ff:fe2f:ea40/64 scope link tentative valid_lft forever preferred_lft forever $ ip a l ens2f1np2 5: ens2f1np2: <NO-CARRIER,BROADCAST,MULTICAST,SLAVE,UP> mtu 1500 qdisc mq master bond0 state DOWN group default qlen 1000 link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff inet6 fe80::20f:53ff:fe2f:ea40/64 scope link tentative valid_lft forever preferred_lft forever Looks like addrconf_sysctl_addr_gen_mode() bypasses the original "is this a slave interface?" check added by commit c2edacf8, and results in an address getting added, while w/the proposed patch added, no address gets added. This simply adds the same gating check to another code path, and thus should prevent the same devices from erroneously obtaining an ipv6 link-local address. Fixes: d35a00b8 ("net/ipv6: allow sysctl to change link-local address generation mode") Reported-by: NMoshe Levi <moshele@mellanox.com> CC: Stephen Hemminger <stephen@networkplumber.org> CC: Marcelo Ricardo Leitner <mleitner@redhat.com> CC: netdev@vger.kernel.org Signed-off-by: NJarod Wilson <jarod@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Cong Wang 提交于
Although we intentionally use an ordered workqueue for all tc filter works, the ordering is not guaranteed by RCU work, given that tcf_queue_work() is esstenially a call_rcu(). This problem is demostrated by Thomas: CPU 0: tcf_queue_work() tcf_queue_work(&r->rwork, tcindex_destroy_rexts_work); -> Migration to CPU 1 CPU 1: tcf_queue_work(&p->rwork, tcindex_destroy_work); so the 2nd work could be queued before the 1st one, which leads to a free-after-free. Enforcing this order in RCU work is hard as it requires to change RCU code too. Fortunately we can workaround this problem in tcindex filter by taking a temporary refcnt, we only refcnt it right before we begin to destroy it. This simplifies the code a lot as a full refcnt requires much more changes in tcindex_set_parms(). Reported-by: syzbot+46f513c3033d592409d2@syzkaller.appspotmail.com Fixes: 3d210534 ("net_sched: fix a race condition in tcindex_destroy()") Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Paul E. McKenney <paulmck@kernel.org> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com> Reviewed-by: NPaul E. McKenney <paulmck@kernel.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 01 4月, 2020 3 次提交
-
-
由 Gustavo A. R. Silva 提交于
In case memory resources for buf were allocated, release them before return. Addresses-Coverity-ID: 1492011 ("Resource leak") Fixes: a7a29f9c ("net: ipv6: add rpl sr tunnel") Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Russell King 提交于
Fix an oops in dsa_port_phylink_mac_change() caused by a combination of a20f9970 ("net: dsa: Don't instantiate phylink for CPU/DSA ports unless needed") and the net-dsa-improve-serdes-integration series of patches 65b7a2c8 ("Merge branch 'net-dsa-improve-serdes-integration'"). Unable to handle kernel NULL pointer dereference at virtual address 00000124 pgd = c0004000 [00000124] *pgd=00000000 Internal error: Oops: 805 [#1] SMP ARM Modules linked in: tag_edsa spi_nor mtd xhci_plat_hcd mv88e6xxx(+) xhci_hcd armada_thermal marvell_cesa dsa_core ehci_orion libdes phy_armada38x_comphy at24 mcp3021 sfp evbug spi_orion sff mdio_i2c CPU: 1 PID: 214 Comm: irq/55-mv88e6xx Not tainted 5.6.0+ #470 Hardware name: Marvell Armada 380/385 (Device Tree) PC is at phylink_mac_change+0x10/0x88 LR is at mv88e6352_serdes_irq_status+0x74/0x94 [mv88e6xxx] Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk> Reviewed-by: NVivien Didelot <vivien.didelot@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bruno Meneguele 提交于
A testing message was brought by 13d0f7b8 ("net/bpfilter: fix dprintf usage for /dev/kmsg") but should've been deleted before patch submission. Although it doesn't cause any harm to the code or functionality itself, it's totally unpleasant to have it displayed on every loop iteration with no real use case. Thus remove it unconditionally. Fixes: 13d0f7b8 ("net/bpfilter: fix dprintf usage for /dev/kmsg") Signed-off-by: NBruno Meneguele <bmeneg@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 31 3月, 2020 18 次提交
-
-
由 Ido Schimmel 提交于
The previous patch allowed device drivers to publish their default binding between packet trap policers and packet trap groups. However, some users might not be content with this binding and would like to change it. In case user space passed a packet trap policer identifier when setting a packet trap group, invoke the appropriate device driver callback and pass the new policer identifier. v2: * Check for presence of 'DEVLINK_ATTR_TRAP_POLICER_ID' in devlink_trap_group_set() and bail if not present * Add extack error message in case trap group was partially modified Signed-off-by: NIdo Schimmel <idosch@mellanox.com> Reviewed-by: NJiri Pirko <jiri@mellanox.com> Acked-by: NJakub Kicinski <kuba@kernel.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ido Schimmel 提交于
Packet trap groups are used to aggregate logically related packet traps. Currently, these groups allow user space to batch operations such as setting the trap action of all member traps. In order to prevent the CPU from being overwhelmed by too many trapped packets, it is desirable to bind a packet trap policer to these groups. For example, to limit all the packets that encountered an exception during routing to 10Kpps. Allow device drivers to bind default packet trap policers to packet trap groups when the latter are registered with devlink. The next patch will enable user space to change this default binding. Signed-off-by: NIdo Schimmel <idosch@mellanox.com> Reviewed-by: NJiri Pirko <jiri@mellanox.com> Reviewed-by: NJakub Kicinski <kuba@kernel.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ido Schimmel 提交于
Devices capable of offloading the kernel's datapath and perform functions such as bridging and routing must also be able to send (trap) specific packets to the kernel (i.e., the CPU) for processing. For example, a device acting as a multicast-aware bridge must be able to trap IGMP membership reports to the kernel for processing by the bridge module. In most cases, the underlying device is capable of handling packet rates that are several orders of magnitude higher compared to those that can be handled by the CPU. Therefore, in order to prevent the underlying device from overwhelming the CPU, devices usually include packet trap policers that are able to police the trapped packets to rates that can be handled by the CPU. This patch allows capable device drivers to register their supported packet trap policers with devlink. User space can then tune the parameters of these policer (currently, rate and burst size) and read from the device the number of packets that were dropped by the policer, if supported. Subsequent patches in the series will allow device drivers to create default binding between these policers and packet trap groups and allow user space to change the binding. v2: * Add 'strict_start_type' in devlink policy * Have device drivers provide max/min rate/burst size for each policer. Use them to check validity of user provided parameters Signed-off-by: NIdo Schimmel <idosch@mellanox.com> Reviewed-by: NJiri Pirko <jiri@mellanox.com> Reviewed-by: NJakub Kicinski <kuba@kernel.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joe Stringer 提交于
Avoid taking a reference on listen sockets by checking the socket type in the sk_assign and in the corresponding skb_steal_sock() code in the the transport layer, and by ensuring that the prefetch free (sock_pfree) function uses the same logic to check whether the socket is refcounted. Suggested-by: NMartin KaFai Lau <kafai@fb.com> Signed-off-by: NJoe Stringer <joe@wand.net.nz> Signed-off-by: NAlexei Starovoitov <ast@kernel.org> Acked-by: NMartin KaFai Lau <kafai@fb.com> Link: https://lore.kernel.org/bpf/20200329225342.16317-4-joe@wand.net.nz
-
由 Joe Stringer 提交于
Refactor the UDP/TCP handlers slightly to allow skb_steal_sock() to make the determination of whether the socket is reference counted in the case where it is prefetched by earlier logic such as early_demux. Signed-off-by: NJoe Stringer <joe@wand.net.nz> Signed-off-by: NAlexei Starovoitov <ast@kernel.org> Acked-by: NMartin KaFai Lau <kafai@fb.com> Link: https://lore.kernel.org/bpf/20200329225342.16317-3-joe@wand.net.nz
-
由 Joe Stringer 提交于
Add support for TPROXY via a new bpf helper, bpf_sk_assign(). This helper requires the BPF program to discover the socket via a call to bpf_sk*_lookup_*(), then pass this socket to the new helper. The helper takes its own reference to the socket in addition to any existing reference that may or may not currently be obtained for the duration of BPF processing. For the destination socket to receive the traffic, the traffic must be routed towards that socket via local route. The simplest example route is below, but in practice you may want to route traffic more narrowly (eg by CIDR): $ ip route add local default dev lo This patch avoids trying to introduce an extra bit into the skb->sk, as that would require more invasive changes to all code interacting with the socket to ensure that the bit is handled correctly, such as all error-handling cases along the path from the helper in BPF through to the orphan path in the input. Instead, we opt to use the destructor variable to switch on the prefetch of the socket. Signed-off-by: NJoe Stringer <joe@wand.net.nz> Signed-off-by: NAlexei Starovoitov <ast@kernel.org> Acked-by: NMartin KaFai Lau <kafai@fb.com> Link: https://lore.kernel.org/bpf/20200329225342.16317-2-joe@wand.net.nz
-
由 Haishuang Yan 提交于
If outer_proto is not set, GCC warning as following: In file included from net/netfilter/ipvs/ip_vs_core.c:52: net/netfilter/ipvs/ip_vs_core.c: In function 'ip_vs_in_icmp': include/net/ip_vs.h:233:4: warning: 'outer_proto' may be used uninitialized in this function [-Wmaybe-uninitialized] 233 | printk(KERN_DEBUG pr_fmt(msg), ##__VA_ARGS__); \ | ^~~~~~ net/netfilter/ipvs/ip_vs_core.c:1666:8: note: 'outer_proto' was declared here 1666 | char *outer_proto; | ^~~~~~~~~~~ Fixes: 73348fed ("ipvs: optimize tunnel dumps for icmp errors") Signed-off-by: NHaishuang Yan <yanhaishuang@cmss.chinamobile.com> Acked-by: NJulian Anastasov <ja@ssi.bg> Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
-
由 Sergey Marinkevich 提交于
I got a problem on MIPS with Big-Endian is turned on: every time when NF trying to change TCP MSS it returns because of new.v16 was greater than old.v16. But real MSS was 1460 and my rule was like this: add rule table chain tcp option maxseg size set 1400 And 1400 is lesser that 1460, not greater. Later I founded that main causer is cast from u32 to __be16. Debugging: In example MSS = 1400(HEX: 0x578). Here is representation of each byte like it is in memory by addresses from left to right(e.g. [0x0 0x1 0x2 0x3]). LE — Little-Endian system, BE — Big-Endian, left column is type. LE BE u32: [78 05 00 00] [00 00 05 78] As you can see, u32 representation will be casted to u16 from different half of 4-byte address range. But actually nf_tables uses registers and store data of various size. Actually TCP MSS stored in 2 bytes. But registers are still u32 in definition: struct nft_regs { union { u32 data[20]; struct nft_verdict verdict; }; }; So, access like regs->data[priv->sreg] exactly u32. So, according to table presents above, per-byte representation of stored TCP MSS in register will be: LE BE (u32)regs->data[]: [78 05 00 00] [05 78 00 00] ^^ ^^ We see that register uses just half of u32 and other 2 bytes may be used for some another data. But in nft_exthdr_tcp_set_eval() it casted just like u32 -> __be16: new.v16 = src But u32 overfill __be16, so it get 2 low bytes. For clarity draw one more table(<xx xx> means that bytes will be used for cast). LE BE u32: [<78 05> 00 00] [00 00 <05 78>] (u32)regs->data[]: [<78 05> 00 00] [05 78 <00 00>] As you can see, for Little-Endian nothing changes, but for Big-endian we take the wrong half. In my case there is some other data instead of zeros, so new MSS was wrongly greater. For shooting this bug I used solution for ports ranges. Applying of this patch does not affect Little-Endian systems. Signed-off-by: NSergey Marinkevich <sergey.marinkevich@eltex-co.ru> Acked-by: NFlorian Westphal <fw@strlen.de> Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
-
由 Vladimir Oltean 提交于
The approach taken to pass the port policer methods on to drivers is pragmatic. It is similar to the port mirroring implementation (in that the DSA core does all of the filter block interaction and only passes simple operations for the driver to implement) and dissimilar to how flow-based policers are going to be implemented (where the driver has full control over the flow_cls_offload data structure). Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vladimir Oltean 提交于
Make room for other actions for the matchall filter by keeping the mirred argument parsing self-contained in its own function. Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eran Ben Elisha 提交于
On low memory system, run time dumps can consume too much memory. Add administrator ability to disable auto dumps per reporter as part of the error flow handle routine. This attribute is not relevant while executing DEVLINK_CMD_HEALTH_REPORTER_DUMP_GET. By default, auto dump is activated for any reporter that has a dump method, as part of the reporter registration to devlink. Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com> Reviewed-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eran Ben Elisha 提交于
When health reporter is registered to devlink, devlink will implicitly set auto recover if and only if the reporter has a recover method. No reason to explicitly get the auto recover flag from the driver. Remove this flag from all drivers that called devlink_health_reporter_create. All existing health reporters set auto recovery to true if they have a recover method. Yet, administrator can unset auto recover via netlink command as prior to this patch. Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com> Reviewed-by: NJiri Pirko <jiri@mellanox.com> Reviewed-by: NJakub Kicinski <kuba@kernel.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiri Pirko 提交于
The rest of the devlink code sets the extack message using NL_SET_ERR_MSG_MOD. Change the existing appearances of NL_SET_ERR_MSG to NL_SET_ERR_MSG_MOD. Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiri Pirko 提交于
It may be up to the driver (in case ANY HW stats is passed) to select which type of HW stats he is going to use. Add an infrastructure to expose this information to user. $ tc filter add dev enp3s0np1 ingress proto ip handle 1 pref 1 flower dst_ip 192.168.1.1 action drop $ tc -s filter show dev enp3s0np1 ingress filter protocol ip pref 1 flower chain 0 filter protocol ip pref 1 flower chain 0 handle 0x1 eth_type ipv4 dst_ip 192.168.1.1 in_hw in_hw_count 2 action order 1: gact action drop random type none pass val 0 index 1 ref 1 bind 1 installed 10 sec used 10 sec Action statistics: Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0) backlog 0b 0p requeues 0 used_hw_stats immediate <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiri Pirko 提交于
Introduce a helper to pass value and selector to. The helper packs them into struct and puts them into netlink message. Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Christophe JAILLET 提交于
There is no point in preparing the module name in a buffer. The format string can be passed diectly to 'request_module()'. This axes a few lines of code and cleans a few things: - max len for a driver name is MODULE_NAME_LEN wich is ~ 60 chars, not 128. It would be down-sized in 'request_module()' - we should pass the total size of the buffer to 'snprintf()', not the size minus 1 Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Westphal 提交于
Xin Long says: On udp rx path udp_rcv_segment() may do segment where the frag skbs will get the header copied from the head skb in skb_segment_list() by calling __copy_skb_header(), which could overwrite the frag skbs' extensions by __skb_ext_copy() and cause a leak. This issue was found after loading esp_offload where a sec path ext is set in the skb. Fix this by discarding head state of the fraglist skb before replacing its contents. Fixes: 3a1296a3 ("net: Support GRO/GSO fraglist chaining.") Cc: Steffen Klassert <steffen.klassert@secunet.com> Reported-by: NXiumei Mu <xmu@redhat.com> Tested-by: NXin Long <lucien.xin@gmail.com> Signed-off-by: NFlorian Westphal <fw@strlen.de> Acked-by: NSteffen Klassert <steffen.klassert@secunet.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Xin Long 提交于
Without NAPI_GRO_CB(skb)->is_flist initialized, when the dev doesn't support NETIF_F_GRO_FRAGLIST, is_flist can still be set and fraglist will be used in udp_gro_receive(). So fix it by initializing is_flist with 0 in udp_gro_receive. Fixes: 9fd1ff5d ("udp: Support UDP fraglist GRO/GSO.") Signed-off-by: NXin Long <lucien.xin@gmail.com> Acked-by: NSteffen Klassert <steffen.klassert@secunet.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 30 3月, 2020 17 次提交
-
-
由 Michal Kubecek 提交于
Implement TSINFO_GET request to get timestamping information for a network device. This is traditionally available via ETHTOOL_GET_TS_INFO ioctl request. Move part of ethtool_get_ts_info() into common.c so that ioctl and netlink code use the same logic to get timestamping information from the device. v3: use "TSINFO" rather than "TIMESTAMP", suggested by Richard Cochran Signed-off-by: NMichal Kubecek <mkubecek@suse.cz> Acked-by: NRichard Cochran <richardcochran@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michal Kubecek 提交于
Add three string sets related to timestamping information: ETH_SS_SOF_TIMESTAMPING: SOF_TIMESTAMPING_* flags ETH_SS_TS_TX_TYPES: timestamping Tx types ETH_SS_TS_RX_FILTERS: timestamping Rx filters These will be used for TIMESTAMP_GET request. v2: avoid compiler warning ("enumeration value not handled in switch") in net_hwtstamp_validate() v3: omit dash in Tx type names ("one-step-*" -> "onestep-*"), suggested by Richard Cochran Signed-off-by: NMichal Kubecek <mkubecek@suse.cz> Acked-by: NRichard Cochran <richardcochran@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michal Kubecek 提交于
Send ETHTOOL_MSG_EEE_NTF notification whenever EEE settings of a network device are modified using ETHTOOL_MSG_EEE_SET netlink message or ETHTOOL_SEEE ioctl request. Signed-off-by: NMichal Kubecek <mkubecek@suse.cz> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michal Kubecek 提交于
Implement EEE_SET netlink request to set EEE settings of a network device. These are traditionally set with ETHTOOL_SEEE ioctl request. The netlink interface allows setting the EEE status for all link modes supported by kernel but only first 32 link modes can be set at the moment as only those are supported by the ethtool_ops callback. Signed-off-by: NMichal Kubecek <mkubecek@suse.cz> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michal Kubecek 提交于
Implement EEE_GET request to get EEE settings of a network device. These are traditionally available via ETHTOOL_GEEE ioctl request. The netlink interface allows reporting EEE status for all link modes supported by kernel but only first 32 link modes are provided at the moment as only those are reported by the ethtool_ops callback and drivers. v2: fix alignment (whitespace only) Signed-off-by: NMichal Kubecek <mkubecek@suse.cz> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michal Kubecek 提交于
Send ETHTOOL_MSG_PAUSE_NTF notification whenever pause parameters of a network device are modified using ETHTOOL_MSG_PAUSE_SET netlink message or ETHTOOL_SPAUSEPARAM ioctl request. Signed-off-by: NMichal Kubecek <mkubecek@suse.cz> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michal Kubecek 提交于
Implement PAUSE_SET netlink request to set pause parameters of a network device. Thease are traditionally set with ETHTOOL_SPAUSEPARAM ioctl request. Signed-off-by: NMichal Kubecek <mkubecek@suse.cz> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michal Kubecek 提交于
Implement PAUSE_GET request to get pause parameters of a network device. These are traditionally available via ETHTOOL_GPAUSEPARAM ioctl request. Signed-off-by: NMichal Kubecek <mkubecek@suse.cz> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michal Kubecek 提交于
Send ETHTOOL_MSG_COALESCE_NTF notification whenever coalescing parameters of a network device are modified using ETHTOOL_MSG_COALESCE_SET netlink message or ETHTOOL_SCOALESCE ioctl request. Signed-off-by: NMichal Kubecek <mkubecek@suse.cz> Reviewed-by: NJakub Kicinski <kuba@kernel.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michal Kubecek 提交于
Implement COALESCE_SET netlink request to set coalescing parameters of a network device. These are traditionally set with ETHTOOL_SCOALESCE ioctl request. This commit adds only support for device coalescing parameters, not per queue coalescing parameters. Like the ioctl implementation, the generic ethtool code checks if only supported parameters are modified; if not, first offending attribute is reported using extack. v2: fix alignment (whitespace only) Signed-off-by: NMichal Kubecek <mkubecek@suse.cz> Reviewed-by: NJakub Kicinski <kuba@kernel.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michal Kubecek 提交于
Implement COALESCE_GET request to get coalescing parameters of a network device. These are traditionally available via ETHTOOL_GCOALESCE ioctl request. This commit adds only support for device coalescing parameters, not per queue coalescing parameters. Omit attributes with zero values unless they are declared as supported (i.e. the corresponding bit in ethtool_ops::supported_coalesce_params is set). Signed-off-by: NMichal Kubecek <mkubecek@suse.cz> Reviewed-by: NJakub Kicinski <kuba@kernel.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michal Kubecek 提交于
Andrew noticed that some handlers for *_SET commands leak a netdev reference if required ethtool_ops callbacks do not exist. One of them is ethnl_set_privflags(), a simple reproducer would be e.g. ip link add veth1 type veth peer name veth2 ethtool --set-priv-flags veth1 foo on ip link del veth1 Make sure dev_put() is called when ethtool_ops check fails. Fixes: f265d799 ("ethtool: set device private flags with PRIVFLAGS_SET request") Reported-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NMichal Kubecek <mkubecek@suse.cz> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexander Aring 提交于
This patch adds functionality to configure routes for RPL source routing functionality. There is no IPIP functionality yet implemented which can be added later when the cases when to use IPv6 encapuslation comes more clear. Signed-off-by: NAlexander Aring <alex.aring@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexander Aring 提交于
The build_state callback of lwtunnel doesn't contain the net namespace structure yet. This patch will add it so we can check on specific address configuration at creation time of rpl source routes. Signed-off-by: NAlexander Aring <alex.aring@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexander Aring 提交于
This patch adds rpl source routing receive handling. Everything works only if sysconf "rpl_seg_enabled" and source routing is enabled. Mostly the same behaviour as IPv6 segmentation routing. To handle compression and uncompression a rpl.c file is created which contains the necessary functionality. The receive handling will also care about IPv6 encapsulated so far it's specified as possible nexthdr in RFC 6554. Signed-off-by: NAlexander Aring <alex.aring@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexander Aring 提交于
This patch adds a functionality to addrconf to check on a specific RPL address configuration. According to RFC 6554: To detect loops in the SRH, a router MUST determine if the SRH includes multiple addresses assigned to any interface on that router. If such addresses appear more than once and are separated by at least one address not assigned to that router. Signed-off-by: NAlexander Aring <alex.aring@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 William Dauchy 提交于
when creating a new ipip interface with no local/remote configuration, the lookup is done with TUNNEL_NO_KEY flag, making it impossible to match the new interface (only possible match being fallback or metada case interface); e.g: `ip link add tunl1 type ipip dev eth0` To fix this case, adding a flag check before the key comparison so we permit to match an interface with no local/remote config; it also avoids breaking possible userland tools relying on TUNNEL_NO_KEY flag and uninitialised key. context being on my side, I'm creating an extra ipip interface attached to the physical one, and moving it to a dedicated namespace. Fixes: c5441932 ("GRE: Refactor GRE tunneling code.") Signed-off-by: NWilliam Dauchy <w.dauchy@criteo.com> Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-