This patch adjust the coalescing parameters to the vendor
recommendations for the PPv2 network controller.
Suggested-by: NYan Markman <ymarkman@marvell.com>
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the tx-usec value to the informations reported to
ethtool by the get_coalesce function.
Suggested-by: NYan Markman <ymarkman@marvell.com>
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cosmetic patch aligning values in the ethtool get_coalesce function.
This patch do not modify in anyway the driver's behaviour.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Rx/Tx ring sizes can be adjusted thanks to ethtool given specific
network needs. This commit splits the default ring size from its max
value to allow ethtool to vary the parameters in both ways.
Signed-off-by: NYan Markman <ymarkman@marvell.com>
[Antoine: commit message]
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a check to only free the TSO header buffer when its
allocation previously succeeded.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
tcp: better receiver autotuning

Now TCP senders no longer backoff when a drop is detected,
it appears we are very often receive window limited.

This series makes tcp_rcv_space_adjust() slightly more robust
and responsive.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Back in linux-3.13 (commit b0983d3c ("tcp: fix dynamic right sizing"))
I addressed the pressing issues we had with receiver autotuning.

But DRS suffers from extra latencies caused by rcv_rtt_est.rtt_us
drifts. One common problem happens during slow start, since the
apparent RTT measured by the receiver can be inflated by ~50%,
at the end of one packet train.

Also, a single drop can delay read() calls by one RTT, meaning
tcp_rcv_space_adjust() can be called one RTT too late.

By replacing the tri-modal heuristic with a continuous function,
we can offset the effects of not growing 'at the optimal time'.

The curve of the function matches prior behavior if the space
increased by 25% and 50% exactly.

Cost of added multiply/divide is small, considering a TCP flow
typically would run this part of the code few times in its life.

I tested this patch with 100 ms RTT / 1% loss link, 100 runs
of (netperf -l 5), and got an average throughput of 4600 Mbit
instead of 1700 Mbit.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Acked-by: NSoheil Hassas Yeganeh <soheil@google.com>
Acked-by: NWei Wang <weiwan@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using large tcp_rmem[2] values (I did tests with 500 MB),
I noticed overflows while computing rcvwin.

Lets fix this before the following patch.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Acked-by: NSoheil Hassas Yeganeh <soheil@google.com>
Acked-by: NWei Wang <weiwan@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While rcvbuf is properly clamped by tcp_rmem[2], rcvwin
is left to a potentially too big value.

It has no serious effect, since :
1) tcp_grow_window() has very strict checks.
2) window_clamp can be mangled by user space to any value anyway.

tcp_init_buffer_space() and companions use tcp_full_space(),
we use tcp_win_from_space() to avoid reloading sk->sk_rcvbuf
Signed-off-by: NEric Dumazet <edumazet@google.com>
Acked-by: NSoheil Hassas Yeganeh <soheil@google.com>
Acked-by: NWei Wang <weiwan@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since both tx_ring and first_tx are the head of tx ring, it not
necessary to use two structure members to statically indicate
the head of tx ring. So first_tx is removed.

CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: NZhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
nfp: dead code, clean ups and slight improvements

This series contains small clean ups from John and Carl, and brings
no functional changes.

John's improvements target the flower code.  First he makes sure we don't
allocate space in FW request messages for MAC matches if the TC rule does
not contain any.  The remaining two patches remove some dead code and
unused defines.

Carl follows up with a slight optimization to his recent ethtool FW state
dumps, byte swapping input parameters once instead of the data for every
dumped item.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert the requested dump level parameter to big-endian at the start of
nfp_net_dump_calculate_size() and nfp_net_dump_populate_buffer(), then
compare and assign it directly where needed in the traversal and prolog
code. This decreases the total number of conversions used.
Signed-off-by: NCarl Heymann <carl.heymann@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Delete match field defines that are not supported at this time.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Port matching is selected by default on every rule so remove check for it
and delete 'else' side of the statement. Remove nfp_flower_meta_one as now
it will not feature in the code. Rename nfp_flower_meta_two given that one
has been removed.

'Additional metadata' if statement can never be true so remove it as well.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the matching of mac/mpls as a default selection. These are not
necessarily set by a TC rule (unlike the port). Previously a mac/mpls
field would exist in every match and be masked out if not used. This patch
has no impact on functionality but removes unnessary memory assignment in
the match cmsg.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The GPIO polarity passed to phy-reset-gpio is ignored by the FEC
driver and it is assumed to be active low.

It can be active high only when the 'phy-reset-active-high' property
is present.

The current examples pass active high polarity and work fine, but
in order to improve the documentation make it explicit what the real
polarity is.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Acked-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Xin Long says:

====================
sctp: Implement Stream Interleave: The I-DATA Chunk Supporting User Message Interleaving

Stream Interleave would be Implemented in two Parts:

   1. The I-DATA Chunk Supporting User Message Interleaving
   2. Interaction with Other SCTP Extensions

Overview in section 1.1 of RFC8260 for Part 1:

   This document describes a new chunk carrying payload data called
   I-DATA.  This chunk incorporates the properties of the current SCTP
   DATA chunk, all the flags and fields except the Stream Sequence
   Number (SSN), and also adds two new fields in its chunk header -- the
   Fragment Sequence Number (FSN) and the Message Identifier (MID).  The
   FSN is only used for reassembling all fragments that have the same
   MID and the same ordering property.  The TSN is only used for the
   reliable transfer in combination with Selective Acknowledgment (SACK)
   chunks.

   In addition, the MID is also used for ensuring ordered delivery
   instead of using the stream sequence number (the I-DATA chunk omits
   an SSN).

As the 1st part of Stream Interleave Implementation, this patchset adds
an ops framework named sctp_stream_interleave with a bunch of stuff that
does lots of things needed somewhere.

Then it defines sctp_stream_interleave_0 to work for normal DATA chunks
and sctp_stream_interleave_1 for I-DATA chunks.

With these functions, hundreds of if-else checks for the different process
on I-DATA chunks would be avoided. Besides, very few codes could be shared
in these two function sets.

In this patchset, it adds some basic variables, structures and socket
options firstly, then implement these functions one by one to add the
procedures for ordered idata gradually, at last adjusts some codes to
make them work for unordered idata.

To make it safe to be implemented and also not break the normal data
chunk process, this feature can't be enabled to use until all stream
interleave codes are completely accomplished.

v1 -> v2:
  - fixed a checkpatch warning that a blank line was missed.
  - avoided a kbuild warning reported from gcc-4.9.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unordered idata process is more complicated than unordered data:

 - It has to add mid into sctp_stream_out to save the next mid value,
   which is separated from ordered idata's.

 - To support pd for unordered idata, another mid and pd_mode need to
   be added to save the message id and pd state in sctp_stream_in.

 - To make  unordered idata reasm easier, it adds a new event queue
   to save frags for idata.

The patch mostly adds the samilar reasm functions for unordered idata
as ordered idata's, and also adjusts some other codes on assign_mid,
abort_pd and ulpevent_data for idata.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

abort_pd is added as a member of sctp_stream_interleave, used to abort
partial delivery for data or idata, called in sctp_cmd_assoc_failed.

Since stream interleave allows to do partial delivery for each stream
at the same time, sctp_intl_abort_pd for idata would be very different
from the old function sctp_ulpq_abort_pd for data.

Note that sctp_ulpevent_make_pdapi will support per stream in this
patch by adding pdapi_stream and pdapi_seq in sctp_pdapi_event, as
described in section 6.1.7 of RFC6458.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

start_pd is added as a member of sctp_stream_interleave, used to
do partial_delivery for data or idata when datalen >= asoc->rwnd
in sctp_eat_data. The codes have been done in last patches, but
they need to be extracted into start_pd, so that it could be used
for SCTP_CMD_PART_DELIVER cmd as well.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

renege_events is added as a member of sctp_stream_interleave, used to
renege some old data or idata in reasm or lobby queue properly to free
some memory for the new data when there's memory stress.

It defines sctp_renege_events for idata, and leaves sctp_ulpq_renege
as it is for data.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

enqueue_event is added as a member of sctp_stream_interleave, used to
enqueue either data, idata or notification events into user socket rx
queue.

It replaces sctp_ulpq_tail_event used in the other places with
enqueue_event.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ulpevent_data is added as a member of sctp_stream_interleave, used to
do the most process in ulpq, including to convert data or idata chunk
to event, reasm them in reasm queue and put them in lobby queue in
right order, and deliver them up to user sk rx queue.

This procedure is described in section 2.2.3 of RFC8260.

It adds most functions for idata here to do the similar process as
the old functions for data. But since the details are very different
between them, the old functions can not be reused for idata.

event->ssn and event->ppid settings are moved to ulpevent_data from
sctp_ulpevent_make_rcvmsg, so that sctp_ulpevent_make_rcvmsg could
work for both data and idata.

Note that mid is added in sctp_ulpevent for idata, __packed has to
be used for defining sctp_ulpevent, or it would exceeds the skb cb
that saves a sctp_ulpevent variable for ulp layer process.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

validate_data is added as a member of sctp_stream_interleave, used
to validate ssn/chunk type for data or mid (message id)/chunk type
for idata, called in sctp_eat_data.

If this check fails, an abort packet will be sent, as said in
section 2.2.3 of RFC8260.

It also adds the process for idata in rx path. As Marcelo pointed
out, there's no need to add event table for idata, but just share
chunk_event_table with data's. It would drop data chunk for idata
and drop idata chunk for data by calling validate_data in
sctp_eat_data.

As last patch did, it also replaces sizeof(struct sctp_data_chunk)
with sctp_datachk_len for rx path.

After this patch, the idata can be accepted and delivered to ulp
layer.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

assign_number is added as a member of sctp_stream_interleave, used
to assign ssn for data or mid (message id) for idata, called in
sctp_packet_append_data. sctp_chunk_assign_ssn is left as it is,
and sctp_chunk_assign_mid is added for sctp_stream_interleave_1.

This procedure is described in section 2.2.2 of RFC8260.

All sizeof(struct sctp_data_chunk) in tx path is replaced with
sctp_datachk_len, to make it right for idata as well. And also
adjust sctp_chunk_is_data for SCTP_CID_I_DATA.

After this patch, idata can be built and sent in tx path.

Note that if sp strm_interleave is set, it has to wait_connect in
sctp_sendmsg, as asoc intl_enable need to be known after 4 shake-
hands, to decide if it should use data or idata later. data and
idata can't be mixed to send in one asoc.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To avoid hundreds of checks for the different process on I-DATA chunk,
struct sctp_stream_interleave is defined as a group of functions used
to replace the codes in some place where it needs to do different job
according to if the asoc intl_enabled is set.

With these ops, it only needs to initialize asoc->stream.si with
sctp_stream_interleave_0 for normal data if asoc intl_enable is 0,
or sctp_stream_interleave_1 for idata if asoc intl_enable is set in
sctp_stream_init.

After that, the members in asoc->stream.si can be used directly in
some special places without checking asoc intl_enable.

make_datafrag is the first member for sctp_stream_interleave, it's
used to make data or idata frags, called in sctp_datamsg_from_user.
The old function sctp_make_datafrag_empty needs to be adjust some
to fit in this ops.

Note that as idata and data chunks have different length, it also
defines data_chunk_len for sctp_stream_interleave to describe the
chunk size.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sctp_idatahdr and sctp_idata_chunk are used to define and parse
I-DATA chunk format, and sctp_make_idata is a function to build
the chunk.

The I-DATA Chunk Format is defined in section 2.1 of RFC8260.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

asoc intl_enable will be set when local sp strm_interleave is set
and there's I-DATA chunk in init and init_ack extensions, as said
in section 2.2.1 of RFC8260.

asoc intl_enable indicates all data will be sent as I-DATA chunks.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds intl_enable in asoc and netns, and strm_interleave in
sctp_sock to indicate if stream interleave is enabled and supported.

netns intl_enable would be set via procfs, but that is not added yet
until all stream interleave codes are completely implemented; asoc
intl_enable will be set when doing 4-shakehands.

sp strm_interleave can be set by sockopt SCTP_INTERLEAVING_SUPPORTED
which is also added in this patch. This socket option is defined in
section 4.3.1 of RFC8260.

Note that strm_interleave can only be set by sockopt when both netns
intl_enable and sp frag_interleave are set.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Packets that don't have dest mac as the mac of the master device should
not be entertained by the IPvlan rx-handler. This is mostly true as the
packet path mostly takes care of that, except when the master device is
a virtual device. As demonstrated in the following case -

  ip netns add ns1
  ip link add ve1 type veth peer name ve2
  ip link add link ve2 name iv1 type ipvlan mode l2
  ip link set dev iv1 netns ns1
  ip link set ve1 up
  ip link set ve2 up
  ip -n ns1 link set iv1 up
  ip addr add 192.168.10.1/24 dev ve1
  ip -n ns1 addr 192.168.10.2/24 dev iv1
  ping -c2 192.168.10.2
  <Works!>
  ip neigh show dev ve1
  ip neigh show 192.168.10.2 lladdr <random> dev ve1
  ping -c2 192.168.10.2
  <Still works! Wrong!!>

This patch adds that missing check in the IPvlan rx-handler.
Reported-by: NAmit Sikka <amit.sikka@ericsson.com>
Signed-off-by: NMahesh Bandewar <maheshb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Both netlink_add_tap() and netlink_remove_tap() are
called in process context, no need to bother spinlock.

Note, in fact, currently we always hold RTNL when calling
these two functions, so we don't need any other lock at
all, but keeping this lock doesn't harm anything.

Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

nlmon device is not supposed to capture netlink events from
other netns, so instead of filtering events, we can simply
make netlink tap itself per netns.

Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tom Herbert says:

====================
rhashtable: New features in walk and bucket

This patch contains some changes to related rhashtable:

- Above allow rhashtable_walk_start to return void
- Add a functon to peek at the next entry during a walk
- Abstract out function to compute a has for a table
- A library function to alloc a spinlocks bucket array
- Call the above function for rhashtable locks allocation

Tested: Exercised using various operations on an ILA xlat
table.

v2:
 - Apply feedback from Herbert. Don't change semantics of resize
   event reporting and -EAGAIN, just simplify API for callers that
   ignore those.
 - Add end_of_table in iter to reliably tell when the iterator has
   reached to the eno.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To allocate the array of bucket locks for the hash table we now
call library function alloc_bucket_spinlocks. This function is
based on the old alloc_bucket_locks in rhashtable and should
produce the same effect.
Signed-off-by: NTom Herbert <tom@quantonium.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add two new library functions: alloc_bucket_spinlocks and
free_bucket_spinlocks. These are used to allocate and free an array
of spinlocks that are useful as locks for hash buckets. The interface
specifies the maximum number of spinlocks in the array as well
as a CPU multiplier to derive the number of spinlocks to allocate.
The number allocated is rounded up to a power of two to make the
array amenable to hash lookup.
Signed-off-by: NTom Herbert <tom@quantonium.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Split out most of rht_key_hashfn which is calculating the hash into
its own function. This way the hash function can be called separately to
get the hash value.
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NTom Herbert <tom@quantonium.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This function is like rhashtable_walk_next except that it only returns
the current element in the inter and does not advance the iter.

This patch also creates __rhashtable_walk_find_next. It finds the next
element in the table when the entry cached in iter is NULL or at the end
of a slot. __rhashtable_walk_find_next is called from
rhashtable_walk_next and rhastable_walk_peek.

end_of_table is an added field to the iter structure. This indicates
that the end of table was reached (walker.tbl being NULL is not a
sufficient condition for end of table).
Signed-off-by: NTom Herbert <tom@quantonium.net>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most callers of rhashtable_walk_start don't care about a resize event
which is indicated by a return value of -EAGAIN. So calls to
rhashtable_walk_start are wrapped wih code to ignore -EAGAIN. Something
like this is common:

       ret = rhashtable_walk_start(rhiter);
       if (ret && ret != -EAGAIN)
               goto out;

Since zero and -EAGAIN are the only possible return values from the
function this check is pointless. The condition never evaluates to true.

This patch changes rhashtable_walk_start to return void. This simplifies
code for the callers that ignore -EAGAIN. For the few cases where the
caller cares about the resize event, particularly where the table can be
walked in mulitple parts for netlink or seq file dump, the function
rhashtable_walk_start_check has been added that returns -EAGAIN on a
resize event.
Signed-off-by: NTom Herbert <tom@quantonium.net>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes: 46e6b992 ("rtnetlink: allow GSO maximums to be set on device creation")
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflict was two parallel additions of include files to sch_generic.c,
no biggie.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>