Due to typo error driver was failing TMF Abort Task request when
ctask->sc != NULL. Fixed code to fail TMF ABORT Task request only when
ctask->sc == NULL.  Clear age component (19 most significant bits) of
reference ITT carried in iSCSI TMF PDU. Age component is internal to
initiator side and only lower bits of ITT as defined by ISCSI_ITT_MASK
is is sent on wire.  Retrieve LUN directly from the ref_sc and update
SQ wqe as per chip HSI (Host Software Interface) specification
Signed-off-by: NAnil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Only affects 5771x (10G chipsets) devices

This is an optimized CQ arming algoritm which takes into account the
number of outstanding tasks
Signed-off-by: NAnil Veerabhadrappa <anilgv@broadcom.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This issue was discovered during 10G iscsi testing

Default value of 'sq_size' module parameter is '0' which means driver
should use predefined SQ queue size when setting up iscsi connection.

roundup_pow_of_two(0) results in '1' and forces driver to setup
connections with send queue size of '1' and results in lower
performance as well
Signed-off-by: NAnil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NAnil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

After commits c82f63e4 (PCI: check saved
state before restore) and 4b77b0a2 (PCI:
Clear saved_state after the state has been restored) PCI drivers are
prevented from restoring the device standard configuration registers
twice in a row. These changes introduced a regression on ipr EEH
recovery.

The ipr device driver saves the PCI state only during the device probe
and restores it on ipr_reset_restore_cfg_space() during IOA resets. This
behavior is causing the EEH recovery to fail after the second error
detected, since the registers are not being restored.

One possible solution would be saving the registers after restoring
them. The problem with this approach is that while recovering from an
EEH error if pci_save_state() results in an EEH error, the adapter/slot
will be reset, and end up back in ipr_reset_restore_cfg_space(), but it
won't have a valid saved state to restore, so pci_restore_state() will
fail.

The following patch introduces a workaround for this problem, hacking
around the PCI API by setting pdev->state_saved = true before we do the
restore. It fixes the EEH regression and prevents that we hit another
EEH error during EEH recovery.


[jejb: fix is a hack ... Jesse and Rafael will fix properly]
Signed-off-by: NKleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

If the LLD wants its own WWNN/WWPN to be used, it should implement the
netdev_ops.ndo_fcoe_get_wwn(). If that is the case, we query the LLD and use
the queried WWNN/WWPN from the LLD.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

 Fix to accommodate a hardware bug in multiqueue mode that does not
 work properly when acknowledgement of MSIX Interrupts is disabled.
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Removed the module parameters ql2xqfulltracking and ql2xqfullrampup
since the queue depth ramp up/down functionality is moved to scsi-ml.
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Fix crash in qla2x00_fdmi_register() due to the dpc
thread executing before the scsi host has been fully
added.

Unable to handle kernel NULL pointer dereference (address 00000000000001d0)
qla2xxx_7_dpc[4140]: Oops 8813272891392 [1]

Call Trace:
 [<a000000100016910>] show_stack+0x50/0xa0
                                sp=e00000b07c59f930 bsp=e00000b07c591400
 [<a000000100017180>] show_regs+0x820/0x860
                                sp=e00000b07c59fb00 bsp=e00000b07c5913a0
 [<a00000010003bd60>] die+0x1a0/0x2e0
                                sp=e00000b07c59fb00 bsp=e00000b07c591360
 [<a0000001000681a0>] ia64_do_page_fault+0x8c0/0x9e0
                                sp=e00000b07c59fb00 bsp=e00000b07c591310
 [<a00000010000c8e0>] ia64_native_leave_kernel+0x0/0x270
                                sp=e00000b07c59fb90 bsp=e00000b07c591310
 [<a000000207197350>] qla2x00_fdmi_register+0x850/0xbe0 [qla2xxx]
                                sp=e00000b07c59fd60 bsp=e00000b07c591290
 [<a000000207171570>] qla2x00_configure_loop+0x1930/0x34c0 [qla2xxx]
                                sp=e00000b07c59fd60 bsp=e00000b07c591128
 [<a0000002071732b0>] qla2x00_loop_resync+0x1b0/0x2e0 [qla2xxx]
                                sp=e00000b07c59fdf0 bsp=e00000b07c5910c0
 [<a000000207166d40>] qla2x00_do_dpc+0x9a0/0xce0 [qla2xxx]
                                sp=e00000b07c59fdf0 bsp=e00000b07c590fa0
 [<a0000001000d5bb0>] kthread+0x110/0x140
                                sp=e00000b07c59fe00 bsp=e00000b07c590f68
 [<a000000100014a30>] kernel_thread_helper+0xd0/0x100
                                sp=e00000b07c59fe30 bsp=e00000b07c590f40
 [<a00000010000a4c0>] start_kernel_thread+0x20/0x40
                                sp=e00000b07c59fe30 bsp=e00000b07c590f40

crash> dis a000000207197350
0xa000000207197350 <qla2x00_fdmi_register+2128>:        [MMI]       ld1 r45=[r14];;
crash> scsi_qla_host.host 0xe00000b058c73ff8
  host = 0xe00000b058c73be0,
crash> Scsi_Host.shost_data 0xe00000b058c73be0
  shost_data = 0x0,  <<<<<<<<<<<

The fc_transport fc_* workqueue threads have yet to be created.

crash> ps | grep _7
   3891      2   2  e00000b075c80000  IN   0.0       0      0  [scsi_eh_7]
   4140      2   3  e00000b07c590000  RU   0.0       0      0  [qla2xxx_7_dpc]

The thread creating adding the Scsi_Host is blocked due to other
activity in sysfs.

crash> bt 3762
PID: 3762   TASK: e00000b071e70000  CPU: 3   COMMAND: "modprobe"
 #0 [BSP:e00000b071e71548] schedule at a000000100727e00
 #1 [BSP:e00000b071e714c8] __mutex_lock_slowpath at a0000001007295a0
 #2 [BSP:e00000b071e714a8] mutex_lock at a000000100729830
 #3 [BSP:e00000b071e71478] sysfs_addrm_start at a0000001002584f0
 #4 [BSP:e00000b071e71440] create_dir at a000000100259350
 #5 [BSP:e00000b071e71410] sysfs_create_subdir at a000000100259510
 #6 [BSP:e00000b071e713b0] internal_create_group at a00000010025c880
 #7 [BSP:e00000b071e71388] sysfs_create_group at a00000010025cc50
 #8 [BSP:e00000b071e71368] dpm_sysfs_add at a000000100425050
 #9 [BSP:e00000b071e71310] device_add at a000000100417d90
#10 [BSP:e00000b071e712d8] scsi_add_host at a00000010045a380
#11 [BSP:e00000b071e71268] qla2x00_probe_one at a0000002071be950
#12 [BSP:e00000b071e71248] local_pci_probe at a00000010032e490
#13 [BSP:e00000b071e71218] pci_device_probe at a00000010032ecd0
#14 [BSP:e00000b071e711d8] driver_probe_device at a00000010041d480
#15 [BSP:e00000b071e711a8] __driver_attach at a00000010041d6e0
#16 [BSP:e00000b071e71170] bus_for_each_dev at a00000010041c240
#17 [BSP:e00000b071e71150] driver_attach at a00000010041d0a0
#18 [BSP:e00000b071e71108] bus_add_driver at a00000010041b080
#19 [BSP:e00000b071e710c0] driver_register at a00000010041dea0
#20 [BSP:e00000b071e71088] __pci_register_driver at a00000010032f610
#21 [BSP:e00000b071e71058] (unknown) at a000000207200270
#22 [BSP:e00000b071e71018] do_one_initcall at a00000010000a9c0
#23 [BSP:e00000b071e70f98] sys_init_module at a0000001000fef00
#24 [BSP:e00000b071e70f98] ia64_ret_from_syscall at a00000010000c740

So, it appears that qla2xxx dpc thread is moving forward before the
scsi host has been completely added.

This patch moves the setting of the init_done (and online) flag to
after the call to scsi_add_host() to hold off the dpc thread.

Found via large lun count testing using 2.6.31.
Signed-off-by: NMichael Reed <mdr@sgi.com>
Acked-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Cc: stable@kernel.org
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

So libosd has decided to sacrifice some code simplicity for the sake of
a clean API. One of these things is the possibility for users to call
osd_end_request, in any condition at any state. This opens up some
problems with calling blk_put_request when out-side of the completion
callback but calling __blk_put_request when detecting a from-completion
state.

The current hack was working just fine until exofs decided to operate on
all devices in parallel and wait for the sum of the requests, before
deallocating all osd-requests at once. There are two new possible cases
1. All request in a group are deallocated as part of the last request's
   async-done, request_queue is locked.
2. All request in a group where executed asynchronously, but
   de-allocation was delayed to after the async-done, in the context of
   another thread. Async execution but request_queue is not locked.

The solution I chose was to separate the deallocation of the osd_request
which has the information users need, from the deallocation of the
internal(2) requests which impose the locking problem. The internal
block-requests are freed unconditionally inside the async-done-callback,
when we know the queue is always locked. If at osd_end_request time we
still have a bock-request, then we know it did not come from within an
async-done-callback and we can call the regular blk_put_request.

The internal requests were used for carrying error information after
execution. This information is now copied to osd_request members for
later analysis by user code.

The external API and behaviour was unchanged, except now it really
supports what was previously advertised.
Reported-by: NVineet Agarwal <checkout.vineet@gmail.com>
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

On the large servers, I/O port resource may not be assigned to all
the PCI devices since it is limited (to 64KB on Intel Architecture[1])
and it may also be fragmented (I/O base register of PCI-to-PCI bridge
will usually be aligned to a 4KB boundary[2]).
If no I/O port resource is assigned to devices, those devices do not
work.

[1] Some machines support 64KB I/O port space per PCI segment.
[2] Some P2P bridges support optional 1KB aligned I/O base.

Therefore, I made a patch for MegaRAID SAS driver to make PCI legacy
I/O port free.  I have also tested the patch and it had no problem.

The way to make PCI legacy I/O port free is the same as Fusion-MPT
driver's and it has been merged into 2.6.30.4.

This has already been fixed in e1000 and lpfc.

As a result of the above, the driver can handle its device even when
there are a huge number of PCI devices being used on the system and no
I/O port region assigned to the device.
Signed-off-by: NNoriyuki Fujii <n-fujii@np.css.fujitsu.com>
Acked-by: N"Yang, Bo" <Bo.Yang@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

A thin provisioned device may temporarily be out of sufficient
allocation units to fulfill a write request.  In that case it will
return a space allocation in progress error.  Wait a bit and retry the
write.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Implement a function for handling discard requests that sends either
WRITE SAME(16) or UNMAP(10) depending on parameters indicated by the
device in the block limits VPD.

Extract unmap constraints and report them to the block layer.

Based in part by a patch by Christoph Hellwig <hch@lst.de>.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

dio transfer always resets mdata->page_order to zero. It breaks
high-order pages previously allocated for non-dio transfer.

This patches adds reserved_page_order to st_buffer structure to save
page order for non-dio transfer.

http://bugzilla.kernel.org/show_bug.cgi?id=14563

When enlarge_buffer() allocates 524288 from 0, st uses six-order page
allocation. So mdata->page_order is 6 and frp_seg is 2.

After that, if st uses dio, sgl_map_user_pages() sets
mdata->page_order to 0 for st_do_scsi(). After that, when we call
normalize_buffer(), it frees only free frp_seg * PAGE_SIZE (2 * 4096)
though we should free frp_seg * PAGE_SIZE << 6 (2 * 4096 << 6). So we
see buffer_size is set to 516096 (524288 - 8192).
Reported-by: NJoachim Breuer <linux-kernel@jmbreuer.net>
Tested-by: NJoachim Breuer <linux-kernel@jmbreuer.net>
Acked-by: NKai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: stable@kernel.org
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch allows for future addition of various async messages
from the chip. This ensures that the driver won't hit a BUG_ON if
the Firmware used is newer than inbox driver and so is using
latest async messages.
Signed-off-by: NJayamohan Kallickal <jayamohank@serverengines.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This is support for Adaptec ASC-1045/1405 SAS/SATA HBA on mvsas, which
is based on Marvell 88SE6440 chipset.
Signed-off-by: NSrinivas <satyasrinivasp@hcl.in>
Cc: Andy Yan <ayan@marvell.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

PMC-Sierra mgmt application uses SMI-S model. According to SMI-S, the
object model exposed by the SMI-S provider should show an StoragePool
which contains member disks of a RAID Virtual disk and StorageVolume
based on the StoragePool. But according to SMI-S, there is a possibility
where StoragePool is created but StorageVolume is not yet created. To
satisfy this scenario, we are trying a hidden RAID Virtual disk. The
hidden RAID virtual disk will not be exposed to OS. Once a StorageVolume
is created for this RAID virtual disk it is exposed.

Signed-off-by: Anil Ravindranath<anil_ravindranath@pmc-sierra.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

If transport_class_register fails we should unregister any
registered classes, or we will leak memory or other
resources.

I did a quick modprobe of scsi_transport_fc to test the
patch.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Internal command scsih_cmds init is included in mpt2sas_base_attach.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch adds two new IBM storage devices which can use rdac device handlers.
Signed-off-by: NBabu Moger <babu.moger@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

In testing 2.6.31 on one of our ia64 platforms I've encountered a hang
due to the driver using hardware ATEs which are a limited resource.
This is because the driver does not set the dma consistent mask to
64 bits.
Signed-off-by: NMichael Reed <mdr@sgi.com>
Acked-by: NJames Smart <James.Smart@Emulex.Com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

"Definition" is misspelled "defintion" in several comments; this
patch fixes them. No code changes.
Signed-off-by: NAdam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Upon receiving ELS_RLS, send the Link Error Status Block (LESB) back.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Add a member function pointer as get_lesb to libfc_function_template so LLD
can fill the LESB based on its own statistics. For fcoe, it fills the LESB
as a fcoe_fc_els_lesb struct according to FC-BB-5.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Add tracking the Missing Discovery Advertisement count for FIP Fiber Channel
Forwarder (FCF) as described in FC-BB-5 Rev2.0 for LESB. The time is 1.5 times
the FKA_ADV_PERIOD of the corresponding FCF.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Add tracking the Virtual Link Failure count when either we have found
the FCF as "aged" or we are receiving FIP Clear Virtual Link from the
FCF.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

When the D bit is set if the FKA_ADV_Period of the FIP Discovery
Advertisement, the ENode should not transmit period ENode FIP Keep Alive and
VN_Port FIP Keep Alive (FC-BB-5 Rev2, 7.8.3.13).

Note that fcf->flags is taken directly from the fip_header, I am claiming one
bit for the purpose of the FIP_FKA_Period D bit as FIP_FL_FK_ADV_B, and use
FIP_HEADER_FLAGS as bitmask for bits used in fip_header.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Allow FCP frames to bypass the FCoE receive processing threads and handle
them directly in softirq context, if they are received on the correct CPU.
This preserves the queuing to threads for scaling out receive processing
to multiple CPUs, but allows FCoE-aware multi-queue network drivers that
direct frames to the originating CPUs to handle FCP processing with less
scheduling latency.

Only FCP is handled directly, because libfc makes use of mutexes in ELS
handling routines.

The bulk of this change is just moving the FCoE receive processing out of
the receive thread function, leaving behind just the thread and queue
management.  The interesting bits are in fcoe_rcv()
Signed-off-by: NChris Leech <christopher.leech@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Frame header room is already incluced, just pass the length of payload.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Hardware related Fixes and Changes.
 - Added new Adapter IDs and update default Adapter names.
 - Added PCI read after EQarm doorbell PCI write to flush the write
   and avoid spurrious interrupts when in INTx mode.
 - Phase out use of ONLINE registers.
 - Fix for lost MSI interrupt
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Fix errors relating to crashes and hangs.
 - Fix crash due to list corruption while unloading driver.
 - Fix panic during pci-hot-plug testing.
 - Fix panic when unmapping luns.
 - Fixed total_scsi_bufs counting could cause exhausted memory.
 - Fixed locking issue causing hang.
 - Fixed the call from lpfc_new_scsi_buf_s3 to use lpfc_release_scsi_buf_s3.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Fix AER issues.
 - Made AER sysfs entry point return "Operation not permitted" to
   OneConnect HBAs
 - Stop and abort all I/Os on HBA for AER uncorrectable non-fatal error
   handling
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

FC protocol fixes.
 - Fix send sequence logic to handle multi SGL IOCBs.
 - Fix FDISC completion always setting VPORT state to failed.
 - Ported the fix on reporting of max_vpi to uppper layer.
 - Fix incorrect number of Vports allowed to be created.
 - Fixed Dead FCoE port after creating vports.
 - Added handling of ELS request for Reinstate Recovery Qualifier (RRQ)
 - Handle unsolicited CT exchange initiator receiving CT exchange ABTS
 - Migrate LUN queue depth ramp up code to scsi mid-layer.
 - Made ABTS WQE go to the same WQ as the WQE to be aborted.
 - Fix Vport does not rediscover after FCF goes away.
 - Fixed lpfc_unreg_vfi failure after devloss timeout.
 - Fixed RPI bit leak.
 - Fix hbq pointer corruption during target discovery.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

FCoE Protocol fixes.
 - Fixed FIP frame designation for ELS commands.
 - Fix CVL received on Port 1 not processed by driver.
 - Fix Zeroed frame on wire after FLOGI
 - Fix vport keep-alive does not contain the correct WWN.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

value cannot logically be less than START and greater than BUFFERSIZE.

#define EXTENDED_SENSE_START  18

// vi include/scsi/scsi_cmnd.h +105
#define SCSI_SENSE_BUFFERSIZE 	96

[akpm@linux-foundation.org: fix warning]
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Acked-by: NKai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Fix scsi_devinfo.c kernel-doc function names to match actual function
names.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Administer some love to the osd_req_decode_sense function

* Fix a bad bug with osd_req_decode_sense(). If there was no scsi
  residual, .i.e the request never reached the target, then all the
  osd_sense_info members where garbage.

* Add grossly missing in/out_resid to osd_sense_info and fill them in
  properly.

* Define an osd_err_priority enum which divides the possible errors into
  7 categories in ascending severity. Each category is also assigned a
  Linux return code translation.

  Analyze the different osd/scsi/block returned errors and set the
  proper osd_err_priority and Linux return code accordingly.

* extra check a few situations so not to get stuck with inconsistent
  error view. Example an empty residual with an error code, and other
  places ...

Lots of libosd's osd_req_decode_sense clients had this logic in some
form or another. Consolidate all these into one place that should
actually know about osd returns. Thous translating it to a more
abstract error.
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

When an error was detected in an attribute list do to
a target bug. We would print an error but spin endlessly
regardless. Fix it.
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>