Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 16 9月, 2017 1 次提交
  3. 25 8月, 2017 3 次提交
  5. 08 8月, 2017 1 次提交
  7. 20 6月, 2017 3 次提交
  9. 13 6月, 2017 5 次提交
  11. 17 5月, 2017 9 次提交
  13. 09 5月, 2017 1 次提交
    • J
      scsi: lpfc: Fix panic on BFS configuration · 4492b739
      由 James Smart 提交于 
      To select the appropriate shost template, the driver is issuing a
mailbox command to retrieve the wwn. Turns out the sending of the
command precedes the reset of the function.  On SLI-4 adapters, this is
inconsequential as the mailbox command location is specified by dma via
the BMBX register. However, on SLI-3 adapters, the location of the
mailbox command submission area changes. When the function is first
powered on or reset, the cmd is submitted via PCI bar memory. Later the
driver changes the function config to use host memory and DMA. The
request to start a mailbox command is the same, a simple doorbell write,
regardless of submission area.  So.. if there has not been a boot driver
run against the adapter, the mailbox command works as defaults are
ok. But, if the boot driver has configured the card and, and if no
platform pci function/slot reset occurs as the os starts, the mailbox
command will fail. The SLI-3 device will use the stale boot driver dma
location. This can cause PCI eeh errors.

Fix is to reset the sli-3 function before sending the mailbox command,
thus synchronizing the function/driver on mailbox location.

Note: The fix uses routines that are typically invoked later in the call
flow to reset the sli-3 device. The issue in using those routines is
that the normal (non-fix) flow does additional initialization, namely
the allocation of the pport structure. So, rather than significantly
reworking the initialization flow so that the pport is alloc'd first,
pointer checks are added to work around it. Checks are limited to the
routines invoked by a sli-3 adapter (s3 routines) as this fix/early call
is only invoked on a sli3 adapter. Nothing changes post the
fix. Subsequent initialization, and another adapter reset, still occur -
both on sli-3 and sli-4 adapters.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Fixes: 96418b5e ("scsi: lpfc: Fix eh_deadline setting for sli3 adapters.")
Cc: stable@vger.kernel.org # v4.11+
Reviewed-by: NEwan D. Milne <emilne@redhat.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
      4492b739
  15. 24 4月, 2017 5 次提交
    • J
      Update ABORT processing for NVMET. · 86c67379
      由 James Smart 提交于 
      The driver with nvme had this routine stubbed.

Right now XRI_ABORTED_CQE is not handled and the FC NVMET
Transport has a new API for the driver.

Missing code path, new NVME abort API
Update ABORT processing for NVMET

There are 3 new FC NVMET Transport API/ template routines for NVMET:

lpfc_nvmet_xmt_fcp_release
This NVMET template callback routine called to release context
associated with an IO This routine is ALWAYS called last, even
if the IO was aborted or completed in error.

lpfc_nvmet_xmt_fcp_abort
This NVMET template callback routine called to abort an exchange that
has an IO in progress

nvmet_fc_rcv_fcp_req
When the lpfc driver receives an ABTS, this NVME FC transport layer
callback routine is called. For this case there are 2 paths thru the
driver: the driver either has an outstanding exchange / context for the
XRI to be aborted or not.  If not, a BA_RJT is issued otherwise a BA_ACC

NVMET Driver abort paths:

There are 2 paths for aborting an IO. The first one is we receive an IO and
decide not to process it because of lack of resources. An unsolicated ABTS
is immediately sent back to the initiator as a response.
lpfc_nvmet_unsol_fcp_buffer
            lpfc_nvmet_unsol_issue_abort  (XMIT_SEQUENCE_WQE)

The second one is we sent the IO up to the NVMET transport layer to
process, and for some reason the NVME Transport layer decided to abort the
IO before it completes all its phases. For this case there are 2 paths
thru the driver:
the driver either has an outstanding TSEND/TRECEIVE/TRSP WQE or no
outstanding WQEs are present for the exchange / context.
lpfc_nvmet_xmt_fcp_abort
    if (LPFC_NVMET_IO_INP)
        lpfc_nvmet_sol_fcp_issue_abort  (ABORT_WQE)
                lpfc_nvmet_sol_fcp_abort_cmp
    else
        lpfc_nvmet_unsol_fcp_issue_abort
                lpfc_nvmet_unsol_issue_abort  (XMIT_SEQUENCE_WQE)
                        lpfc_nvmet_unsol_fcp_abort_cmp

Context flags:
LPFC_NVMET_IOP - his flag signifies an IO is in progress on the exchange.
LPFC_NVMET_XBUSY  - this flag indicates the IO completed but the firmware
is still busy with the corresponding exchange. The exchange should not be
reused until after a XRI_ABORTED_CQE is received for that exchange.
LPFC_NVMET_ABORT_OP - this flag signifies an ABORT_WQE was issued on the
exchange.
LPFC_NVMET_CTX_RLS  - this flag signifies a context free was requested,
but we are deferring it due to an XBUSY or ABORT in progress.

A ctxlock is added to the context structure that is used whenever these
flags are set/read  within the context of an IO.
The LPFC_NVMET_CTX_RLS flag is only set in the defer_relase routine when
the transport has resolved all IO associated with the buffer. The flag is
cleared when the CTX is associated with a new IO.

An exchange can has both an LPFC_NVMET_XBUSY and a LPFC_NVMET_ABORT_OP
condition active simultaneously. Both conditions must complete before the
exchange is freed.
When the abort callback (lpfc_nvmet_xmt_fcp_abort) is envoked:
If there is an outstanding IO, the driver will issue an ABORT_WQE. This
should result in 3 completions for the exchange:
1) IO cmpl with XB bit set
2) Abort WQE cmpl
3) XRI_ABORTED_CQE cmpl
For this scenerio, after completion #1, the NVMET Transport IO rsp
callback is called.  After completion #2, no action is taken with respect
to the exchange / context.  After completion #3, the exchange context is
free for re-use on another IO.

If there is no outstanding activity on the exchange, the driver will send a
ABTS to the Initiator. Upon completion of this WQE, the exchange / context
is freed for re-use on another IO.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
      86c67379
    • J
      Fix crash after issuing lip reset · 9d3d340d
      由 James Smart 提交于 
      When RPI is not available, driver sends WQE with invalid RPI value and
rejected by HBA.
lpfc 0000:82:00.3: 1:3154 BLS ABORT RSP failed, data:  x3/xa0320008
and
lpfc :2753 PLOGI failure DID:FFFFFA Status:x3/xa0240008

In this case, driver accesses rpi_ids array out of bounds.

Fix:
Check return value of lpfc_sli4_alloc_rpi(). Do not allocate
lpfc_nodelist entry if RPI is not available.

When RPI is not available, we will get discovery timeouts and
command drops for some of the vports as seen below.

lpfc :0273 Unexpected discovery timeout, vport State x0
lpfc :0230 Unexpected timeout, hba link state x5
lpfc :0111 Dropping received ELS cmd Data: x0 xc90c55 x0
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
      9d3d340d
    • J
      Fix driver usage of 128B WQEs when WQ_CREATE is V1. · 3f247de7
      由 James Smart 提交于 
      There are two versions of a structure for queue creation and setup that the
driver shares with FW. The driver was only treating as version 0.

Verify WQ_CREATE with 128B WQEs in V0 and V1.

Code review of another bug showed the driver passing
128B WQEs and 8 pages in WQ CREATE and V0.
Code inspection/instrumentation showed that the driver
uses V0 in WQ_CREATE and if the caller passes queue->entry_size
128B, the driver sets the hdr_version to V1 so all is good.
When I tested the V1 WQ_CREATE, the mailbox failed causing
the driver to unload.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
      3f247de7
    • J
      Fix driver unload/reload operation. · d1f525aa
      由 James Smart 提交于 
      There are couple of different load/unload issues fixed with this patch.
One of the issues was reported by Junichi Nomura, a patch was submitted
by Johannes Thumsrhirn which did fix one of the problems but the fix in
this patch separates the pring free from the queue free and does not set
the parameter passed in to NULL.

issues:
(1) driver could not be unloaded and reloaded without some Oops or
 Panic occurring.
(2) The driver was panicking because of a corruption in the Memory
Manager when the iocb list was getting allocated.

Root cause for the memory corruption was a double free of the Work Queue
ring pointer memory - Freed once in the lpfc_sli4_queue_free when the CQ
was destroyed and again in lpfc_sli4_queue_free when the WQ was destroyed.

The pring free and the queue free were separated, the pring free was moved
to the wq destroy routine because it a better fit logically to delete the
ring with the wq.

The checkpatch flagged several alignmenet issues that were also corrected
with this patch.

The mboxq was never initialed correctly before it was used by the driver
this patch corrects that issue.
Reported-by: NJunichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Tested-by: NJunichi Nomura <j-nomura@ce.jp.nec.com>
      d1f525aa
    • J
      Fix spelling in comments. · 0ef69968
      由 James Smart 提交于 
      Comment should have said Repost.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
      0ef69968
  17. 07 3月, 2017 4 次提交
  19. 28 2月, 2017 2 次提交
  21. 23 2月, 2017 6 次提交