- 07 1月, 2009 40 次提交
-
-
由 Hugh Dickins 提交于
Change pgoff_t nr_blocks in discard_swap() and discard_swap_cluster() to sector_t: given the constraints on swap offsets (in particular, the 5 bits of swap type accommodated in the same unsigned long), pgoff_t was actually safe as is, but it certainly looked worrying when shifted left. [akpm@linux-foundation.org: fix shift overflow] Signed-off-by: NHugh Dickins <hugh@veritas.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Jens Axboe <jens.axboe@oracle.com> Cc: Matthew Wilcox <matthew@wil.cx> Cc: Joern Engel <joern@logfs.org> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Donjun Shin <djshin90@gmail.com> Cc: Tejun Heo <teheo@suse.de> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
Though attempting to find free clusters (Andrea), swap allocation has always restarted its searches from the beginning of the swap area (sct), to reduce seek times between swap pages, by not scattering them all over the partition. But on a solidstate swap device, seeks are cheap, and block remapping to level the wear may be limited by zones: in that case it's better to cycle around the whole partition. Signed-off-by: NHugh Dickins <hugh@veritas.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Jens Axboe <jens.axboe@oracle.com> Cc: Matthew Wilcox <matthew@wil.cx> Cc: Joern Engel <joern@logfs.org> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Donjun Shin <djshin90@gmail.com> Cc: Tejun Heo <teheo@suse.de> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
Swap allocation has always started from the beginning of the swap area; but if we're dealing with a solidstate swap device which can only remap blocks within limited zones, that would sooner wear out the first zone. Therefore sys_swapon() test whether blk_queue is non-rotational, and if so randomize the cluster_next starting position for allocation. If blk_queue is nonrot, note SWP_SOLIDSTATE for later use, and report it with an "SS" at the right end of the kernel's "Adding ... swap" message (so that if it's both nonrot and discardable, "SSD" will be shown there). Perhaps something should be shown in /proc/swaps (swapon -s), but we have to be more cautious before making any addition to that format. Signed-off-by: NHugh Dickins <hugh@veritas.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Jens Axboe <jens.axboe@oracle.com> Cc: Matthew Wilcox <matthew@wil.cx> Cc: Joern Engel <joern@logfs.org> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Donjun Shin <djshin90@gmail.com> Cc: Tejun Heo <teheo@suse.de> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
When scan_swap_map() finds a free cluster of swap pages to allocate, discard the old contents of the cluster if the device supports discard. But don't bother when swap is so fragmented that we allocate single pages. Be careful about racing allocations made while we're scanning for a cluster; and hold up allocations made while we're discarding. Signed-off-by: NHugh Dickins <hugh@veritas.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Jens Axboe <jens.axboe@oracle.com> Cc: Matthew Wilcox <matthew@wil.cx> Cc: Joern Engel <joern@logfs.org> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Donjun Shin <djshin90@gmail.com> Cc: Tejun Heo <teheo@suse.de> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
When adding swap, all the old data on swap can be forgotten: sys_swapon() discard all but the header page of the swap partition (or every extent but the header of the swap file), to give a solidstate swap device the opportunity to optimize its wear-levelling. If that succeeds, note SWP_DISCARDABLE for later use, and report it with a "D" at the right end of the kernel's "Adding ... swap" message. Perhaps something should be shown in /proc/swaps (swapon -s), but we have to be more cautious before making any addition to that format. Signed-off-by: NHugh Dickins <hugh@veritas.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Jens Axboe <jens.axboe@oracle.com> Cc: Matthew Wilcox <matthew@wil.cx> Cc: Joern Engel <joern@logfs.org> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Donjun Shin <djshin90@gmail.com> Cc: Tejun Heo <teheo@suse.de> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
Before making functional changes, rearrange scan_swap_map() to simplify subsequent diffs. Actually, there is one functional change in there: leave cluster_nr negative while scanning for a new cluster - resetting it early increased the likelihood that when we have difficulty finding a free cluster, another task may come in and try doing exactly the same - just a waste of cpu. Before making functional changes, rearrange struct swap_info_struct slightly: flags will be needed as an unsigned long (for wait_on_bit), next is a good int to pair with prio, old_block_size is uninteresting so shift it to the end. Signed-off-by: NHugh Dickins <hugh@veritas.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
The kernel has not supported v0 SWAP-SPACE since 2.5.22: I think we can now safely drop its "version 0 swap is no longer supported" message - just say "Unable to find swap-space signature" as usual. This removes one level of indentation from a stretch of sys_swapon(). I'd have liked to be specific, saying "Unable to find SWAPSPACE2 signature", but it's just too confusing that the version 1 signature shows the number 2. Irrelevant nearby cleanup: kmap(page) already gives page_address(page). Signed-off-by: NHugh Dickins <hugh@veritas.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
Remove trailing whitespace from swapfile.c, and odd swap_show() alignment. Signed-off-by: NHugh Dickins <hugh@veritas.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
Remove the SWP_ACTIVE mask: it just obscures the SWP_WRITEOK flag. Signed-off-by: NHugh Dickins <hugh@veritas.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
sys_swapon()'s swapfilesize (better renamed swapfilepages) is declared as an int, but should be an unsigned long like the maxpages it's compared against: on 64-bit (with 4kB pages) a swapfile of 2^44 bytes was rejected with "Swap area shorter than signature indicates". Signed-off-by: NHugh Dickins <hugh@veritas.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 KOSAKI Motohiro 提交于
Sparse output following warnings. mm/vmalloc.c:1436:6: warning: symbol 'vread' was not declared. Should it be static? mm/vmalloc.c:1474:6: warning: symbol 'vwrite' was not declared. Should it be static? However, it is used by /dev/kmem. fixed here. Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 KOSAKI Motohiro 提交于
Sparse output following warning. mm/page_alloc.c:4301:6: warning: symbol 'setup_per_zone_inactive_ratio' was not declared. Should it be static? cleanup here. Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 KOSAKI Motohiro 提交于
sparse output following warning mm/vmscan.c:2507:6: warning: symbol 'scan_zone_unevictable_pages' was not declared. Should it be static? cleanup here. Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 KOSAKI Motohiro 提交于
sparse output following warning. mm/vmscan.c:2549:6: warning: symbol 'scan_all_zones_unevictable_pages' was not declared. Should it be static? cleanup here. Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 KOSAKI Motohiro 提交于
Sparse output following warnings. mm/memcontrol.c:782:5: warning: symbol 'mem_cgroup_resize_limit' was not declared. Should it be static? cleanup here. Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 KOSAKI Motohiro 提交于
sparse output following warnings. mm/memory.c:2936:8: warning: incorrect type in assignment (different address spaces) mm/memory.c:2936:8: expected void *maddr mm/memory.c:2936:8: got void [noderef] <asn:2> cleanup here. Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 KOSAKI Motohiro 提交于
Sparse output following warning. mm/page_cgroup.c:100:15: warning: symbol 'init_section_page_cgroup' was not declared. Should it be static? cleanup here. Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 KOSAKI Motohiro 提交于
memcg reclaim shouldn't change zone->recent_rotated statistics. If memcgroup reclaim changes zone statistics, global reclaim can get a bit confused. Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Acked-by: NRik van Riel <riel@redhat.com> Cc: Balbir Singh <balbir@in.ibm.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
Rik suggests a simplified get_scan_ratio() for !CONFIG_SWAP. Yes, the gcc optimizer gives us that, when nr_swap_pages is #defined as 0L. Move usual declaration to swapfile.c: it never belonged in page_alloc.c. Signed-off-by: NHugh Dickins <hugh@veritas.com> Cc: Lee Schermerhorn <lee.schermerhorn@hp.com> Acked-by: NRik van Riel <riel@redhat.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Robin Holt <holt@sgi.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
If we add a failing stub for add_to_swap(), then we can remove the #ifdef CONFIG_SWAP from mm/vmscan.c. This was intended as a source cleanup, but looking more closely, it turns out that the !CONFIG_SWAP case was going to keep_locked for an anonymous page, whereas now it goes to the more suitable activate_locked, like the CONFIG_SWAP nr_swap_pages 0 case. Signed-off-by: NHugh Dickins <hugh@veritas.com> Cc: Lee Schermerhorn <lee.schermerhorn@hp.com> Acked-by: NRik van Riel <riel@redhat.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Robin Holt <holt@sgi.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
Remove gfp_mask argument from add_to_swap(): it's misleading because its only caller, shrink_page_list(), is not atomic at that point; and in due course (implementing discard) we'll sometimes want to allocate some memory with GFP_NOIO (as is used in swap_writepage) when allocating swap. No change to the gfp_mask passed down to add_to_swap_cache(): still use __GFP_HIGH without __GFP_WAIT (with nomemalloc and nowarn as before): though it's not obvious if that's the best combination to ask for here. Signed-off-by: NHugh Dickins <hugh@veritas.com> Cc: Lee Schermerhorn <lee.schermerhorn@hp.com> Cc: Rik van Riel <riel@redhat.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Robin Holt <holt@sgi.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
An unfortunate feature of the Unevictable LRU work was that reclaiming an anonymous page involved an extra scan through the anon_vma: to check that the page is evictable before allocating swap, because the swap could not be freed reliably soon afterwards. Now try_to_free_swap() has replaced remove_exclusive_swap_page(), that's not an issue any more: remove try_to_munlock() call from shrink_page_list(), leaving it to try_to_munmap() to discover if the page is one to be culled to the unevictable list - in which case then try_to_free_swap(). Update unevictable-lru.txt to remove comments on the try_to_munlock() in shrink_page_list(), and shorten some lines over 80 columns. Signed-off-by: NHugh Dickins <hugh@veritas.com> Cc: Lee Schermerhorn <lee.schermerhorn@hp.com> Acked-by: NRik van Riel <riel@redhat.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Robin Holt <holt@sgi.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
There's a possible race in try_to_unuse() which Nick Piggin led me to two years ago. Where it does lock_page() after read_swap_cache_async(), what if another task removed that page from swapcache just before we locked it? It would sail though the (*swap_map > 1) tests doing nothing (because it could not have been removed from swapcache before its swap references were gone), until it reaches the delete_from_swap_cache(page) near the bottom. Now imagine that this page has been allocated to swap on a different swap area while we dropped page lock (perhaps at the top, perhaps in unuse_mm): we could wrongly remove from swap cache before the page has been written to swap, so a subsequent do_swap_page() would read in stale data from swap. I think this case could not happen before: remove_exclusive_swap_page() refused while page count was raised. But now with reuse_swap_page() and try_to_free_swap() removing from swap cache without minding page count, I think it could happen - the previous patch argued that it was safe because try_to_unuse() already ignored page count, but overlooked that it might be breaking the assumptions in try_to_unuse() itself. Signed-off-by: NHugh Dickins <hugh@veritas.com> Cc: Lee Schermerhorn <lee.schermerhorn@hp.com> Cc: Rik van Riel <riel@redhat.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Robin Holt <holt@sgi.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
remove_exclusive_swap_page(): its problem is in living up to its name. It doesn't matter if someone else has a reference to the page (raised page_count); it doesn't matter if the page is mapped into userspace (raised page_mapcount - though that hints it may be worth keeping the swap): all that matters is that there be no more references to the swap (and no writeback in progress). swapoff (try_to_unuse) has been removing pages from swapcache for years, with no concern for page count or page mapcount, and we used to have a comment in lookup_swap_cache() recognizing that: if you go for a page of swapcache, you'll get the right page, but it could have been removed from swapcache by the time you get page lock. So, give up asking for exclusivity: get rid of remove_exclusive_swap_page(), and remove_exclusive_swap_page_ref() and remove_exclusive_swap_page_count() which were spawned for the recent LRU work: replace them by the simpler try_to_free_swap() which just checks page_swapcount(). Similarly, remove the page_count limitation from free_swap_and_count(), but assume that it's worth holding on to the swap if page is mapped and swap nowhere near full. Add a vm_swap_full() test in free_swap_cache()? It would be consistent, but I think we probably have enough for now. Signed-off-by: NHugh Dickins <hugh@veritas.com> Cc: Lee Schermerhorn <lee.schermerhorn@hp.com> Cc: Rik van Riel <riel@redhat.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Robin Holt <holt@sgi.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
A good place to free up old swap is where do_wp_page(), or do_swap_page(), is about to redirty the page: the data on disk is then stale and won't be read again; and if we do decide to write the page out later, using the previous swap location makes an unnecessary disk seek very likely. So give can_share_swap_page() the side-effect of delete_from_swap_cache() when it safely can. And can_share_swap_page() was always a misleading name, the more so if it has a side-effect: rename it reuse_swap_page(). Irrelevant cleanup nearby: remove swap_token_default_timeout definition from swap.h: it's used nowhere. Signed-off-by: NHugh Dickins <hugh@veritas.com> Cc: Lee Schermerhorn <lee.schermerhorn@hp.com> Acked-by: NRik van Riel <riel@redhat.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Robin Holt <holt@sgi.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
An application may rely on get_user_pages() to give it pages writable from userspace and shared with a driver, GUP breaking COW if necessary. It may mprotect() the pages' writability, off and on, from time to time. Normally this works fine (so long as the app does not fork); but just occasionally, under memory pressure, a readonly pte in a newly writable area is COWed unnecessarily, breaking the link with the driver: because do_wp_page() does trylock_page, and falls back to COW whenever that fails. For reliable behaviour in the unshared case, when the trylock_page fails, now unlock pagetable, lock page and relock pagetable, before deciding whether Copy-On-Write is really necessary. Reported-by: Zhou Yingchao Signed-off-by: NHugh Dickins <hugh@veritas.com> Cc: Lee Schermerhorn <lee.schermerhorn@hp.com> Cc: Rik van Riel <riel@redhat.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Robin Holt <holt@sgi.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
do_wp_page()'s VM_FAULT_WRITE return value tells __get_user_pages() that COW has been done if necessary, though it may be leaving the pte without write permission - for the odd case of forced writing to a readonly vma for ptrace. At present GUP then retries the follow_page() without asking for write permission, to escape an endless loop when forced. But an application may be relying on GUP to guarantee a writable page which won't be COWed again when written from userspace, whereas a race here might leave a readonly pte in place? Change the VM_FAULT_WRITE handling to ask follow_page() for write permission again, except in that odd case of forced writing to a readonly vma. Signed-off-by: NHugh Dickins <hugh@veritas.com> Cc: Lee Schermerhorn <lee.schermerhorn@hp.com> Cc: Rik van Riel <riel@redhat.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Robin Holt <holt@sgi.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 David Rientjes 提交于
This change introduces two new sysctls to /proc/sys/vm: dirty_background_bytes and dirty_bytes. dirty_background_bytes is the counterpart to dirty_background_ratio and dirty_bytes is the counterpart to dirty_ratio. With growing memory capacities of individual machines, it's no longer sufficient to specify dirty thresholds as a percentage of the amount of dirtyable memory over the entire system. dirty_background_bytes and dirty_bytes specify quantities of memory, in bytes, that represent the dirty limits for the entire system. If either of these values is set, its value represents the amount of dirty memory that is needed to commence either background or direct writeback. When a `bytes' or `ratio' file is written, its counterpart becomes a function of the written value. For example, if dirty_bytes is written to be 8096, 8K of memory is required to commence direct writeback. dirty_ratio is then functionally equivalent to 8K / the amount of dirtyable memory: dirtyable_memory = free pages + mapped pages + file cache dirty_background_bytes = dirty_background_ratio * dirtyable_memory -or- dirty_background_ratio = dirty_background_bytes / dirtyable_memory AND dirty_bytes = dirty_ratio * dirtyable_memory -or- dirty_ratio = dirty_bytes / dirtyable_memory Only one of dirty_background_bytes and dirty_background_ratio may be specified at a time, and only one of dirty_bytes and dirty_ratio may be specified. When one sysctl is written, the other appears as 0 when read. The `bytes' files operate on a page size granularity since dirty limits are compared with ZVC values, which are in page units. Prior to this change, the minimum dirty_ratio was 5 as implemented by get_dirty_limits() although /proc/sys/vm/dirty_ratio would show any user written value between 0 and 100. This restriction is maintained, but dirty_bytes has a lower limit of only one page. Also prior to this change, the dirty_background_ratio could not equal or exceed dirty_ratio. This restriction is maintained in addition to restricting dirty_background_bytes. If either background threshold equals or exceeds that of the dirty threshold, it is implicitly set to half the dirty threshold. Acked-by: NPeter Zijlstra <peterz@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Christoph Lameter <cl@linux-foundation.org> Signed-off-by: NDavid Rientjes <rientjes@google.com> Cc: Andrea Righi <righi.andrea@gmail.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 David Rientjes 提交于
The background dirty and dirty limits are better defined with type specifiers of unsigned long since negative writeback thresholds are not possible. These values, as returned by get_dirty_limits(), are normally compared with ZVC values to determine whether writeback shall commence or be throttled. Such page counts cannot be negative, so declaring the page limits as signed is unnecessary. Acked-by: NPeter Zijlstra <peterz@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Christoph Lameter <cl@linux-foundation.org> Signed-off-by: NDavid Rientjes <rientjes@google.com> Cc: Andrea Righi <righi.andrea@gmail.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Julia Lawall 提交于
As noted by Akinobu Mita in patch b1fceac2, alloc_bootmem and related functions never return NULL and always return a zeroed region of memory. Thus a NULL test or memset after calls to these functions is unnecessary. This was fixed using the following semantic patch. (http://www.emn.fr/x-info/coccinelle/) // <smpl> @@ expression E; statement S; @@ E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\|alloc_bootmem_node\|alloc_bootmem_low_pages_node\|alloc_bootmem_pages_node\)(...) ... when != E ( - BUG_ON (E == NULL); | - if (E == NULL) S ) @@ expression E,E1; @@ E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\|alloc_bootmem_node\|alloc_bootmem_low_pages_node\|alloc_bootmem_pages_node\)(...) ... when != E - memset(E,0,E1); // </smpl> Signed-off-by: NJulia Lawall <julia@diku.dk> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
Moving lru_cache_add_active_or_unevictable() into page_add_new_anon_rmap() was good but stupid: we can and should SetPageSwapBacked() there too; and we know for sure that this anonymous, swap-backed page is not file cache. Signed-off-by: NHugh Dickins <hugh@veritas.com> Cc: Lee Schermerhorn <lee.schermerhorn@hp.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Acked-by: NRik van Riel <riel@redhat.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
page_lock_anon_vma() and page_unlock_anon_vma() were made available to show_page_path() in vmscan.c; but now that has been removed, make them static in rmap.c again, they're better kept private if possible. Signed-off-by: NHugh Dickins <hugh@veritas.com> Reviewed-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
lru_cache_add_active_or_unevictable() and page_add_new_anon_rmap() always appear together. Save some symbol table space and some jumping around by removing lru_cache_add_active_or_unevictable(), folding its code into page_add_new_anon_rmap(): like how we add file pages to lru just after adding them to page cache. Remove the nearby "TODO: is this safe?" comments (yes, it is safe), and change page_add_new_anon_rmap()'s address BUG_ON to VM_BUG_ON as originally intended. Signed-off-by: NHugh Dickins <hugh@veritas.com> Acked-by: NRik van Riel <riel@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Mel Gorman <mel@csn.ul.ie> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
The swap code is over-provisioned with BUG_ONs on assorted page flags, mostly dating back to 2.3. They're good documentation, and guard against developer error, but a waste of space on most systems: change them to VM_BUG_ONs, conditional on CONFIG_DEBUG_VM. Just delete the PagePrivate ones: they're later, from 2.5.69, but even less interesting now. Signed-off-by: NHugh Dickins <hugh@veritas.com> Reviewed-by: NChristoph Lameter <cl@linux-foundation.org> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Mel Gorman <mel@csn.ul.ie> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
If we add NOOP stubs for SetPageSwapCache() and ClearPageSwapCache(), then we can remove the #ifdef CONFIG_SWAPs from mm/migrate.c. Signed-off-by: NHugh Dickins <hugh@veritas.com> Acked-by: NChristoph Lameter <cl@linux-foundation.org> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Mel Gorman <mel@csn.ul.ie> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
GFP_HIGHUSER_PAGECACHE is just an alias for GFP_HIGHUSER_MOVABLE, making that harder to track down: remove it, and its out-of-work brothers GFP_NOFS_PAGECACHE and GFP_USER_PAGECACHE. Since we're making that improvement to hotremove_migrate_alloc(), I think we can now also remove one of the "o"s from its comment. Signed-off-by: NHugh Dickins <hugh@veritas.com> Acked-by: NMel Gorman <mel@csn.ul.ie> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
cgroup_mm_owner_callbacks() was brought in to support the memrlimit controller, but sneaked into mainline ahead of it. That controller has now been shelved, and the mm_owner_changed() args were inadequate for it anyway (they needed an mm pointer instead of a task pointer). Remove the dead code, and restore mm_update_next_owner() locking to how it was before: taking mmap_sem there does nothing for memcontrol.c, now the only user of mm->owner. Signed-off-by: NHugh Dickins <hugh@veritas.com> Cc: Paul Menage <menage@google.com> Cc: Balbir Singh <balbir@in.ibm.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Franck Bui-Huu 提交于
It is known that buffer_mapped() is false in this code path. Signed-off-by: NFranck Bui-Huu <fbuihuu@gmail.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Jeremy Fitzhardinge 提交于
Make the pte-level function in apply_to_range be called in lazy mmu mode, so that any pagetable modifications can be batched. Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Cc: Hugh Dickins <hugh@veritas.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Nick Piggin 提交于
Lazy unmapping in the vmalloc code has now opened the possibility for use after free bugs to go undetected. We can catch those by forcing an unmap and flush (which is going to be slow, but that's what happens). Signed-off-by: NNick Piggin <npiggin@suse.de> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-