The strncpy() function is being deprecated upstream. Replace
it by the safer strscpy().

While here, replace a few occurences of strlcpy() that were
recently added to also use strscpy().
Reviewed-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

Ref: https://bugzilla.kernel.org/show_bug.cgi?id=199323

Users are experiencing problems with the DVBSky S960/S960C USB devices
since the following commit:

9d659ae1: ("locking/mutex: Add lock handoff to avoid starvation")

The device malfunctions after running for an indeterminable period of
time, and the problem can only be cleared by rebooting the machine.

It is possible to encourage the problem to surface by blocking the
signal to the LNB.

Further debugging revealed the cause of the problem.

In the following capture:
- thread #1325 is running m88ds3103_set_frontend
- thread #42 is running ts2020_stat_work

a> [1325] usb 1-1: dvb_usb_v2_generic_io: >>> 08 68 02 07 80
   [1325] usb 1-1: dvb_usb_v2_generic_io: <<< 08
   [42] usb 1-1: dvb_usb_v2_generic_io: >>> 09 01 01 68 3f
   [42] usb 1-1: dvb_usb_v2_generic_io: <<< 08 ff
   [42] usb 1-1: dvb_usb_v2_generic_io: >>> 08 68 02 03 11
   [42] usb 1-1: dvb_usb_v2_generic_io: <<< 07
   [42] usb 1-1: dvb_usb_v2_generic_io: >>> 09 01 01 60 3d
   [42] usb 1-1: dvb_usb_v2_generic_io: <<< 07 ff
b> [1325] usb 1-1: dvb_usb_v2_generic_io: >>> 08 68 02 07 00
   [1325] usb 1-1: dvb_usb_v2_generic_io: <<< 07
   [42] usb 1-1: dvb_usb_v2_generic_io: >>> 08 68 02 03 11
   [42] usb 1-1: dvb_usb_v2_generic_io: <<< 07
   [42] usb 1-1: dvb_usb_v2_generic_io: >>> 09 01 01 60 21
   [42] usb 1-1: dvb_usb_v2_generic_io: <<< 07 ff
   [42] usb 1-1: dvb_usb_v2_generic_io: >>> 08 68 02 03 11
   [42] usb 1-1: dvb_usb_v2_generic_io: <<< 07
   [42] usb 1-1: dvb_usb_v2_generic_io: >>> 09 01 01 60 66
   [42] usb 1-1: dvb_usb_v2_generic_io: <<< 07 ff
   [1325] usb 1-1: dvb_usb_v2_generic_io: >>> 08 68 02 03 11
   [1325] usb 1-1: dvb_usb_v2_generic_io: <<< 07
   [1325] usb 1-1: dvb_usb_v2_generic_io: >>> 08 60 02 10 0b
   [1325] usb 1-1: dvb_usb_v2_generic_io: <<< 07

Two i2c messages are sent to perform a reset in m88ds3103_set_frontend:

  a. 0x07, 0x80
  b. 0x07, 0x00

However, as shown in the capture, the regmap mutex is being handed over
to another thread (ts2020_stat_work) in between these two messages.

>From here, the device responds to every i2c message with an 07 message,
and will only return to normal operation following a power cycle.

Use regmap_multi_reg_write to group the two reset messages, ensuring
both are processed before the regmap mutex is unlocked.
Signed-off-by: NJames Hutchinson <jahutchinson99@googlemail.com>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

The implementation of strscpy() is more robust and safer.

That's now the recommended way to copy NUL terminated strings.
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: NKees Cook <keescook@chromium.org>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

Right now, satellite frontend drivers specify frequencies in kHz,
while terrestrial/cable ones specify in Hz. That's confusing
for developers.

However, the main problem is that universal frontends capable
of handling both satellite and non-satelite delivery systems
are appearing. We end by needing to hack the drivers in
order to support such hybrid frontends.

So, convert everything to specify frontend frequencies in Hz.
Tested-by: NKatsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

If m88d3103 chip ID is not recognized, the device is not initialized.

However, it returns from probe without any error, causing this OOPS:

[    7.689289] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[    7.689297] pgd = 7b0bd7a7
[    7.689302] [00000000] *pgd=00000000
[    7.689318] Internal error: Oops: 80000005 [#1] SMP ARM
[    7.689322] Modules linked in: dvb_usb_dvbsky(+) m88ds3103 dvb_usb_v2 dvb_core videobuf2_vmalloc videobuf2_memops videobuf2_core crc32_arm_ce videodev media
[    7.689358] CPU: 3 PID: 197 Comm: systemd-udevd Not tainted 4.15.0-mcc+ #23
[    7.689361] Hardware name: BCM2835
[    7.689367] PC is at 0x0
[    7.689382] LR is at m88ds3103_attach+0x194/0x1d0 [m88ds3103]
[    7.689386] pc : [<00000000>]    lr : [<bf0ae1ec>]    psr: 60000013
[    7.689391] sp : ed8e5c20  ip : ed8c1e00  fp : ed8945c0
[    7.689395] r10: ed894000  r9 : ed894378  r8 : eda736c0
[    7.689400] r7 : ed894070  r6 : ed8e5c44  r5 : bf0bb040  r4 : eda77600
[    7.689405] r3 : 00000000  r2 : 00000000  r1 : 00000000  r0 : eda77600
[    7.689412] Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
[    7.689417] Control: 10c5383d  Table: 2d8e806a  DAC: 00000051
[    7.689423] Process systemd-udevd (pid: 197, stack limit = 0xe9dbfb63)
[    7.689428] Stack: (0xed8e5c20 to 0xed8e6000)
[    7.689439] 5c20: ed853a80 eda73640 ed894000 ed8942c0 ed853a80 bf0b9e98 ed894070 bf0b9f10
[    7.689449] 5c40: 00000000 00000000 bf08c17c c08dfc50 00000000 00000000 00000000 00000000
[    7.689459] 5c60: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    7.689468] 5c80: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    7.689479] 5ca0: 00000000 00000000 ed8945c0 ed8942c0 ed894000 ed894830 bf0b9e98 00000000
[    7.689490] 5cc0: ed894378 bf0a3cb4 bf0bc3b0 0000533b ed920540 00000000 00000034 bf0a6434
[    7.689500] 5ce0: ee952070 ed826600 bf0a7038 bf0a2dd8 00000001 bf0a6768 bf0a2f90 ed8943c0
[    7.689511] 5d00: 00000000 c08eca68 ed826620 ed826620 00000000 ee952070 bf0bc034 ee952000
[    7.689521] 5d20: ed826600 bf0bb080 ffffffed c0aa9e9c c0aa9dac ed826620 c16edf6c c168c2c8
[    7.689531] 5d40: c16edf70 00000000 bf0bc034 0000000d 00000000 c08e268c bf0bb080 ed826600
[    7.689541] 5d60: bf0bc034 ed826654 ed826620 bf0bc034 c164c8bc 00000000 00000001 00000000
[    7.689553] 5d80: 00000028 c08e2948 00000000 bf0bc034 c08e2848 c08e0778 ee9f0a58 ed88bab4
[    7.689563] 5da0: bf0bc034 ed90ba80 c168c1f0 c08e1934 bf0bb3bc c17045ac bf0bc034 c164c8bc
[    7.689574] 5dc0: bf0bc034 bf0bb3bc ed91f564 c08e34ec bf0bc000 c164c8bc bf0bc034 c0aa8dc4
[    7.689584] 5de0: ffffe000 00000000 bf0bf000 ed91f600 ed91f564 c03021e4 00000001 00000000
[    7.689595] 5e00: c166e040 8040003f ed853a80 bf0bc448 00000000 c1678174 ed853a80 f0f22000
[    7.689605] 5e20: f0f21fff 8040003f 014000c0 ed91e700 ed91e700 c16d8e68 00000001 ed91e6c0
[    7.689615] 5e40: bf0bc400 00000001 bf0bc400 ed91f564 00000001 00000000 00000028 c03c9a24
[    7.689625] 5e60: 00000001 c03c8c94 ed8e5f50 ed8e5f50 00000001 bf0bc400 ed91f540 c03c8cb0
[    7.689637] 5e80: bf0bc40c 00007fff bf0bc400 c03c60b0 00000000 bf0bc448 00000028 c0e09684
[    7.689647] 5ea0: 00000002 bf0bc530 c1234bf8 bf0bc5dc bf0bc514 c10ebbe8 ffffe000 bf000000
[    7.689657] 5ec0: 00011538 00000000 ed8e5f48 00000000 00000000 00000000 00000000 00000000
[    7.689666] 5ee0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    7.689676] 5f00: 00000000 00000000 7fffffff 00000000 00000013 b6e55a18 0000017b c0309104
[    7.689686] 5f20: ed8e4000 00000000 00510af0 c03c9430 7fffffff 00000000 00000003 00000000
[    7.689697] 5f40: 00000000 f0f0f000 00011538 00000000 f0f107b0 f0f0f000 00011538 f0f1fdb8
[    7.689707] 5f60: f0f1fbe8 f0f1b974 00004000 000041e0 bf0bc3d0 00000001 00000000 000024c4
[    7.689717] 5f80: 0000002d 0000002e 00000019 00000000 00000010 00000000 16894000 00000000
[    7.689727] 5fa0: 00000000 c0308f20 16894000 00000000 00000013 b6e55a18 00000000 b6e5652c
[    7.689737] 5fc0: 16894000 00000000 00000000 0000017b 00020000 00508110 00000000 00510af0
[    7.689748] 5fe0: bef68948 bef68938 b6e4d3d0 b6d32590 60000010 00000013 00000000 00000000
[    7.689790] [<bf0ae1ec>] (m88ds3103_attach [m88ds3103]) from [<bf0b9f10>] (dvbsky_s960c_attach+0x78/0x280 [dvb_usb_dvbsky])
[    7.689821] [<bf0b9f10>] (dvbsky_s960c_attach [dvb_usb_dvbsky]) from [<bf0a3cb4>] (dvb_usbv2_probe+0xa3c/0x1024 [dvb_usb_v2])
[    7.689849] [<bf0a3cb4>] (dvb_usbv2_probe [dvb_usb_v2]) from [<c0aa9e9c>] (usb_probe_interface+0xf0/0x2a8)
[    7.689869] [<c0aa9e9c>] (usb_probe_interface) from [<c08e268c>] (driver_probe_device+0x2f8/0x4b4)
[    7.689881] [<c08e268c>] (driver_probe_device) from [<c08e2948>] (__driver_attach+0x100/0x11c)
[    7.689895] [<c08e2948>] (__driver_attach) from [<c08e0778>] (bus_for_each_dev+0x4c/0x9c)
[    7.689909] [<c08e0778>] (bus_for_each_dev) from [<c08e1934>] (bus_add_driver+0x1c0/0x264)
[    7.689919] [<c08e1934>] (bus_add_driver) from [<c08e34ec>] (driver_register+0x78/0xf4)
[    7.689931] [<c08e34ec>] (driver_register) from [<c0aa8dc4>] (usb_register_driver+0x70/0x134)
[    7.689946] [<c0aa8dc4>] (usb_register_driver) from [<c03021e4>] (do_one_initcall+0x44/0x168)
[    7.689963] [<c03021e4>] (do_one_initcall) from [<c03c9a24>] (do_init_module+0x64/0x1f4)
[    7.689979] [<c03c9a24>] (do_init_module) from [<c03c8cb0>] (load_module+0x20a0/0x25c8)
[    7.689993] [<c03c8cb0>] (load_module) from [<c03c9430>] (SyS_finit_module+0xb4/0xec)
[    7.690007] [<c03c9430>] (SyS_finit_module) from [<c0308f20>] (ret_fast_syscall+0x0/0x54)
[    7.690018] Code: bad PC value

This may happen on normal circumstances, if, for some reason, the demod
hangs and start returning an invalid chip ID:

[   10.394395] m88ds3103 3-0068: Unknown device. Chip_id=00

So, change the logic to cause probe to fail with -ENODEV, preventing
the OOPS.

Detected while testing DVB MMAP patches on Raspberry Pi 3 with
DVBSky S960CI.

Cc: stable@vger.kernel.org
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

These are immutable.  Making them "const" allows the compiler to move
them to the "rodata" section.

Note that cxd2841er_t_c_ops cannot be made "const", because
cxd2841er_attach() modifies it.  Ouch!

[mchehab@s-opensource.com: fix merge conflicts]
Signed-off-by: NMax Kellermann <max.kellermann@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

* remove some unneeded variable initialization
* rename variables
* use min() macro to calc max i2c xfer len
* change bad firmware error code from EFAULT to EINVAL
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

There was some calculations where was kHz used in order to keep
calculation withing 32-bit. Convert all to Hz and use 64-bit
division helpers where needed.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Simplify TS clock divider calculation and programming slightly.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

DiSEqC message sending takes 13.5 ms per byte, which is 54 ms total
when typical 4 byte message is sent. Don't hard-code time limit to
54 ms, but calculate it. Time limit is only used to determine when to
start poll "DiSEqC Tx ready" status from the chip.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

No need to clear negative msb bits as those were dropped in any
case when data is written to register.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select op to be in terms of the i2c mux core instead
of the child adapter.
Tested-by: NAntti Palosaari <crope@iki.fi>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Instead of using the DTV properties cache directly, pass the get
frontend data as an argument. For now, everything should remain
the same, but the next patch will prevent get_frontend to
affect the global cache.

This is needed because several drivers don't care enough to only
change the properties if locked. Due to that, calling
G_PROPERTY before locking on those drivers will make them to
never lock. Ok, those drivers are crap and should never be
merged like that, but the core should not rely that the drivers
would be doing the right thing.
Reviewed-by: NMichael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This patch fix multiple spelling typos found in
various part of kernel.
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Acked-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Device stopped to tuning some channels after regmap conversion.
Reason is that regmap_update_bits() works a bit differently for
partially volatile registers than old homemade routine. Return
back to old routine in order to fix issue.

Fixes: 478932b1

Cc: <stable@kernel.org> # 4.2+
Reported-by: NMark Clarkstone <hello@markclarkstone.co.uk>
Tested-by: NMark Clarkstone <hello@markclarkstone.co.uk>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The TS2020 and TS2022 tuners take an input from the demodulator indicating the
AGC setting on that component that is then used to influence the tuner's own
gain.  This should be taken into account when calculating the gain and signal
strength.

Further, the existing TS2020 driver miscalculates the signal strength as the
result of its calculations can exceed the storage capacity of the 16-bit word
used to return it to userspace.

To this end:

 (1) Add a callback function (->get_agc_pwm()) in the ts2020_config struct that
     the tuner can call to get the AGC PWM value from the demodulator.

 (2) Modify the TS2020 driver to calculate the gain according to Montage's
     specification with the adjustment that we produce a negative value and
     scale it to 0.001dB units (which is what the DVBv5 API will require):

     (a) Callback to the demodulator to retrieve the AGC PWM value and then
     	 turn that into Vagc for incorporation in the calculations.  If the
     	 callback is unset, assume a Vagc of 0.

     (b) Calculate the tuner gain from a combination of Vagc and the tuner's RF
     	 gain and baseband gain settings.

 (3) Turn this into a percentage signal strength as per Montage's
     specification for return to userspace with the DVBv3 API.

 (4) Provide a function in the M88DS3103 demodulator driver that can be used to
     get the AGC PWM value on behalf of the tuner.

 (5) The ts2020_config.get_agc_pwm function should be set by the code that
     stitches together the drivers for each card.

     For the DVBSky cards that use the M88DS3103 with the TS2020 or the TS2022,
     set the get_agc_pwm function to point to m88ds3103_get_agc_pwm.

I have tested this with a DVBSky S952 card which has an M88DS3103 and a TS2022.

Thanks to Montage for providing access to information about the workings of
these parts.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Use regmap for I2C register access.
Remove own I2C repeated mutex as it should not be needed. I2C adapter
lock is already taken when I2C mux adapter is called, no need for
double locking.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Rename driver state from priv to dev.
Use I2C client for correct logging.
Use adapter and address from I2C client structure where needed.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The DVB API was originally defined using typedefs. This is against
Kernel CodingStyle, and there's no good usage here. While we can't
remove its usage on userspace, we can avoid its usage in Kernelspace.

So, let's do it.

This patch was generated by this shell script:

	for j in $(grep typedef include/uapi/linux/dvb/frontend.h |cut -d' ' -f 3); do for i in $(find drivers/media -name '*.[ch]' -type f) $(find drivers/staging/media -name '*.[ch]' -type f); do sed "s,${j}_t,enum $j," <$i >a && mv a $i; done; done

While here, make CodingStyle fixes on the affected lines.
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de> # for drivers/media/firewire/*

We need to set some error codes here.

Fixes: f01919e8 ('[media] m88ds3103: add I2C client binding')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Implement I2C client device binding.
Wrap media attach to driver I2C probe.
Add wrapper from m88ds3103_attach() to m88ds3103_probe() via driver
core in order to provide proper I2C client for legacy media attach
binding.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Use jiffies to set timeout for DiSEqC TX ready polling. Using jiffies
is more elegant solution than looping N times with sleep.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Implement DVBv5 BER statistics.
Wrap legacy DVBv3 BER to DVBv5 BER.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Implement DVBv5 CNR statistics.
Wrap legacy DVBv3 SNR to DVBv5 CNR.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Do not return error from get_frontend() when status is queried, but
the frontend didn't lock yet. The proper behavior is to only update the
cache after having a lock.

[mchehab@osg.samsung.com: fix the patch description]
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Change 'firmare' to 'firmware'
Signed-off-by: NYannick Guerrini <yguerrini@tomshardware.fr>
Acked-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Change 'firmare' to 'firmware'
Signed-off-by: NYannick Guerrini <yguerrini@tomshardware.fr>
Acked-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

GIT_AUTHOR_DATE=1416472158
The release_firmware() function was called in some cases by the
m88ds3103_init() function during error handling even if the passed variable
contained still a null pointer. This implementation detail could be improved
by the introduction of another jump label.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

GIT_AUTHOR_DATE=1416472432
The release_firmware() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

1> When m88ds3103 works in serial ts mode, its serial ts clock is equal to ts master clock and the clock divider is bypassed.
2> The serial ts clock is configed by the bridge driver just like parallel ts clock.
Signed-off-by: NNibble Max <nibble.max@gmail.com>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

M88RS6000 is the integrated chip, which includes tuner and demod. Its
internal demod is similar with M88DS3103 except some registers
definition.

The main different part of this internal demod from others is its
clock/pll generation IP block sitting inside the tuner die. So clock/pll
functions should be configed through its tuner i2c bus, NOT its demod
i2c bus.

The demod of M88RS6000 need the firmware: dvb-demod-m88rs6000.fw
firmware download link:
	http://www.dvbsky.net/download/linux/dvbsky-firmware.tar.gzSigned-off-by: NNibble Max <nibble.max@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Instead of using 0 or 1 for boolean, use the true/false
defines.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Fix coding style issues pointed out by checkpatch.pl.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add some error checking and implement functionality a little bit
differently.

Cc: Nibble Max <nibble.max@gmail.com>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Implement set voltage operation.
Separate TS clock as a own configuration parameter.
Add TS clock polarity parameter.

[crope@iki.fi: merge em28xx driver m88ds3103 config change patch
to that one, in order to keep build unbroken]
Signed-off-by: NNibble Max <nibble.max@gmail.com>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Implement read_ber for BER estimate.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

There was 32-bit calculation overflow. Use div_u64.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Band switching didn't worked always reliably as there was one
register bit set wrong.

Thanks to Robert Schlabbach for pointing this bug and solution.
Reported-by: NRobert Schlabbach <Robert.Schlabbach@gmx.net>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

It was possible that tuner_frequency variable, used for carrier offset
compensation, was uninitialized. That happens when tuner
.get_frequency() callback is not defined.

Currently that case is not possible as only used tuner has this callback.

Coverity CID 1166057: Uninitialized scalar variable (UNINIT)
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>