Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

cuImage needs to know the logical index of the ethernet devices in order
to assign mac addresses.  This adds the needed properties.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
CC: Scott Wood <scottwood@freescale.com>
CC: Kumar Gala <galak@kernel.crashing.org>
CC: Timur Tabi <timur@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch fixes arch/ppc kernels, at least for prep subarch, after
build-id addition.  Without this, kernels were 3 times the size and
bootloader refused to load them.  Now they are back to normal again.

Tested only with Roland McGrath's "Use LDFLAGS_MODULE only for .ko
links" patch applied - boots and works fine.
Signed-off-by: NMeelis Roos <mroos@linux.ee>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Commit 69331af7, "Fixes and cleanups for earlyprintk aka boot console",
resulted in printk output prior to the initialization of the mpsc
console driver not being printed.  That commit causes the mpsc's
CON_PRINTBUFFER flag to be cleared since udbg should have printed
the previous output.

I guess we can no longer ignore udbg. :)

This patch provides udbg_putc() and udbg_getc() functions for the
Marvell mv64x60 chips. These functions are enabled if an mv64x60
port is to be used as the console as determined from the device tree.
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Acked-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

According to PowerPC 440EPx documentation,
MAL0 is comprised of four channels (two transmit and two receive).
Each channel is dedicated to one of two EMAC cores.
This patch fixes Sequoia DTS MAL0 entry and EMAC entries,
assigning correct channel numbers to EMACs.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

According to PowerPC 440EP documentation,
MAL0 consists of 6 channels (4 transmit channels and 2 receive channels)
This patch fixes Bamboo DTS MAL0 "num-rx-chans" entry.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

The patch adds support for the 64-bit resources to the PCI
iomap code.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Implement udbg_getc() for 440, which fixes xmon input.
Signed-off-by: NHollis Blanchard <hollisb@us.ibm.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

A new binding for flash devices was recently introduced.  This updates the
Sequoia DTS to use the new binding and enabled MTD in the defconfig.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Acked-by: NStefan Roese <sr@denx.de>

A new binding for flash devices was recently introduced.  This updates the
Walnut DTS to use the new binding.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>

Add a cuboot wrapper for the Bamboo board.  Additionally, we enable MAC
address fixups for both cuboot and treeboot.

This also removes some obsoleted linker declarations that have been
moved into ops.h
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>

Randy Dunlap noticed an interesting "crashme" behaviour on his dual
Prescott Xeon setup, where he gets page faults with the error code
having a zero "user" bit, but the register state points back to user
mode.

This may be a CPU microcode buglet triggered by some strange instruction
pattern that crashme generates, and loading a microcode update seems to
possibly have fixed it.

Regardless, we really should trust the register state more than the
error code, since it's really the register state that determines whether
we can actually send a signal, or whether we're in kernel mode and need
to oops/kill the process in the case of a page fault.

Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a workaround to address warnings generated on the "n" constraint by
GCC 3.3 and below.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Fix the definition of the ioasic_ssr_lock spinlock to include a proper 
initialisation.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch fixes a crash caused by an interrupt coming in when an IRQ stack
is being torn down.  When this happens, handle_signal will loop, setting up
the IRQ stack again because the tearing down had finished, and handling
whatever signals had come in.

However, to_irq_stack returns a mask of pending signals to be handled, plus
bit zero is set if the IRQ stack was already active, and thus shouldn't be
torn down.  This causes a problem because when handle_signal goes around
the loop, sig will be zero, and to_irq_stack will duly set bit zero in the
returned mask, faking handle_signal into believing that it shouldn't tear
down the IRQ stack and return thread_info pointers back to their original
values.

This will eventually cause a crash, as the IRQ stack thread_info will
continue pointing to the original task_struct and an interrupt will look
into it after it has been freed.

The fix is to stop passing a signal number into to_irq_stack.  Rather, the
pending signals mask is initialized beforehand with the bit for sig already
set.  References to sig in to_irq_stack can be replaced with references to
the mask.

[akpm@linux-foundation.org: use UL]
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Xen ignores all updates to cr4, and some versions will kill the domain if
you try to change its value.  Just ignore all changes.
Signed-off-by: NJeremy Fitzhardinge <jeremy@xensource.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I found a type mismatch in UML that makes host block devices unusable as ubd
devices on x86_64 and other 64 bits systems (segfault of the mm subsystem):

In block/ioctl.c, the following lines show that the BLKGETSIZE ioctl expects
a pointer to a long:

	case BLKGETSIZE:
		if ((bdev->bd_inode->i_size >> 9) > ~0UL)
			return -EFBIG;
		return put_ulong(arg, bdev->bd_inode->i_size >> 9);

In arch/um/os-Linux/file.c, os_file_size calls it with an int.

The ioctl_list man page should be fixed as well.

Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Recent changes to the timekeeping code broke support for the PowerPC 601
processor which doesn't have the usual timebase facility but a slightly
different thing called (yuck) the RTC.

This fixes it, boot tested on an old 601 based PowerMac 7200.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

We forgot to remove the clock_gettime, clock_getres and get_tbfreq vDSO
calls on CPUs that have no timebase such as 601 or 403 (old CPUs that have
different mechanisms and for which the vDSO code will not work properly).
This fixes it.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

find_victim can dereference a NULL pointer when iterating over the list
of victim spus because list_mutex only guarantees spu->ct to be stable,
but of course not to be non-NULL.

Also fix find_victim to not call spu_unbind_context without list_mutex
because that violates the above guarantee.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This saves 4k on non pSeries builds (except for iSeries where it saves
almost 4k).
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

David Gibson pointed out that swapper_pg_dir actually need to be
PGD_TABLE_SIZE bytes long not PAGE_SIZE.  This actually saves 64k in
the bss for a kernel ppc64_defconfig built with CONFIG_PPC_64K_PAGES.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

It is just a C char array, so declare it thusly.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Create a helper function (alloc_maybe_bootmem) that is marked __init_refok
to limit the chances of mistakenly referring to other __init routines.

WARNING: vmlinux.o(.text+0x2a9c4): Section mismatch: reference to .init.text:.__alloc_bootmem (between '.update_dn_pci_info' and '.pci_dn_reconfig_notifier')
WARNING: vmlinux.o(.text+0x36430): Section mismatch: reference to .init.text:.__alloc_bootmem (between '.mpic_msi_init_allocator' and '.find_ht_magic_addr')
WARNING: vmlinux.o(.text+0x5e804): Section mismatch: reference to .init.text:.__alloc_bootmem (between '.celleb_setup_phb' and '.celleb_fake_pci_write_config')
WARNING: vmlinux.o(.text+0x5e8e8): Section mismatch: reference to .init.text:.__alloc_bootmem (between '.celleb_setup_phb' and '.celleb_fake_pci_write_config')
WARNING: vmlinux.o(.text+0x5e968): Section mismatch: reference to .init.text:.__alloc_bootmem (between '.celleb_setup_phb' and '.celleb_fake_pci_write_config')
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Low-power mode implementation for Lite5200b.
Some I/O registers are also saved here.

A recent U-Boot that supports this (lite5200b_PM_config) is needed.
Signed-off-by: NDomen Puncer <domen.puncer@telargo.com>
Signed-off-by: NSylvain Munaut <tnt@246tNt.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch adds DEFINE_SPUFS_ATTRIBUTE(), a wrapper around
DEFINE_SIMPLE_ATTRIBUTE which does the specified locking for the get
routine for us.

Unfortunately we need two get routines (a locked and unlocked version) to
support the coredump code.  This hides one of those (the locked version)
inside the macro foo.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Currently the spu coredump code doesn't respect the ulimit, it should.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Rework spufs_coredump_extra_notes_write() to check for and return errors.

If we're coredumping to a pipe we can't trust file->f_pos, we need to
maintain the foffset value passed to us. The cleanest way to do this is
to have the low level write routine increment foffset when we've
successfully written.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

To start with, arch_notes_size() etc. is a little too ambiguous a name for
my liking, so change the function names to be more explicit.

Calling through macros is ugly, especially with hidden parameters, so don't
do that, call the routines directly.

Use ARCH_HAVE_EXTRA_ELF_NOTES as the only flag, and based on it decide
whether we want the extern declarations or the empty versions.

Since we have empty routines, actually use them in the coredump code to
save a few #ifdefs.

We want to change the handling of foffset so that the write routine updates
foffset as it goes, instead of using file->f_pos (so that writing to a pipe
works).  So pass foffset to the write routine, and for now just set it to
file->f_pos at the end of writing.

It should also be possible for the write routine to fail, so change it to
return int and treat a non-zero return as failure.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Because spufs might be built as a module, we can't have other parts of the
kernel calling directly into it, we need stub routines that check first if the
module is loaded.

Currently we have two structures which hold callbacks for these stubs, the
syscalls are in spufs_calls and the coredump calls are in spufs_coredump_calls.
In both cases the logic for registering/unregistering is essentially the same,
so we can simplify things by combining the two.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Acked-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Acked-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The SPUFS attribute get routines take a void * because the generic attribute
code doesn't know what sort of data it's passing around.

However our internal __spufs_get_foo() routines can take a spu_context *
directly, which saves plonking it in and out of a void * again.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Acked-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The spufs_coredump_read array is NULL terminated, and we also store the size.
We only need one or the other, and the other arrays in file.c are NULL
terminated, so do that.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Because the SPU coredump code might be built as part of a module (spufs),
we have a stub which is called by the coredump code, this routine then calls
into spufs if it's loaded.

Unfortunately the stub returns -ENOSYS if spufs is not loaded, which is
interpreted by the coredump code as an extra note size of -38 bytes. This
leads to a corrupt core dump.

If spufs is not loaded there will be no SPU ELF notes to write, and so the
extra notes size will be == 0.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Acked-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The routine to dump the local store, __spufs_mem_read(), does not take the
spu_lslr_RW value into account - so we shouldn't check it when we're
calculating the size either.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Acked-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Unfortunately GDB expects some of the SPU coredump values to be identical
in format to what is found in spufs. This means we need to dump some of
the values as ASCII strings, not the actual values.

Because we don't know what the values will be, we always print the values
with the format "0x%.16lx", that way we know the result will be 19 bytes.

do_coredump_read() doesn't take a __user buffer, so remove the annotation,
and because we know that it's safe to just snprintf() directly to it.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The spufs_coredump_reader array contains the size of the data that will be
returned by the read routine.  Currently these are specified as literals,
and though some are obvious, sizeof(u32) == 4, others are not, 69 * 8 ==  ???

Instead, use sizeof() whatever type is returned by each routine, or in
the case of spufs_mem_read() the #define LS_SIZE.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

It makes sense to stop the SPU processes as soon as possible.  Also if we
dont acquire_saved() I think there's a possibility that the value in
csa.priv2.spu_lslr_RW won't be accurate.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Remove the ctx_info struct entirely, and also the ctx_info_list.  This
fixes a race where two processes can clobber each other's ctx_info structs.

Instead of using the list, we just repeat the search through the file
descriptor table.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>