This adds support for Set Privacy Mode when updating the resolving list
when HCI_CONN_FLAG_DEVICE_PRIVACY so the controller shall use Device
Mode for devices programmed in the resolving list, Device Mode is
actually required when the remote device are not able to use RPA as
otherwise the default mode is Network Privacy Mode in which only
allows RPAs thus the controller would filter out advertisement using
identity addresses for which there is an IRK.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This introduces HCI_CONN_FLAG_DEVICE_PRIVACY which can be used by
userspace to indicate to the controller to use Device Privacy Mode to a
specific device.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This makes btusb to queue ACL and events during a polling interval
by using of a delayed work, with the interval working as a time window
where frames received from different endpoints are considered to be
arrived at same time and then attempt to resolve potential conflics by
processing the events ahead of ACL packets.

It worth noting though that priorizing events over ACL data may result
in inverting the order compared to how they appeared over the air, for
instance there may be packets received before a disconnect event that
will be discarded and unencrypted packets received before encryption
change which would considered encrypted, because of these potential
changes on the order the support for queuing during the polling
interval is not enabled by default so it requires setting
force_poll_sync debugfs while the adapter is down.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This reworks hci_conn_params flags to use bitmap_* helpers and add
support for setting the supported flags in hdev->conn_flags so it can
easily be accessed.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This make use of hci_dev_test_and_{set,clear}_flag instead of doing 2
operations in a row.

Fixes: cbbdfa6f ("Bluetooth: Enable controller RPA resolution using Experimental feature")
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Some Macs with the T2 security chip had Bluetooth not working.
To fix it we add DMI based quirks to disable querying of LE Tx power.
Signed-off-by: NAditya Garg <gargaditya08@live.com>
Reported-by: NOrlando Chamberlain <redecorating@protonmail.com>
Tested-by: NOrlando Chamberlain <redecorating@protonmail.com>
Link:
https://lore.kernel.org/r/4970a940-211b-25d6-edab-21a815313954@protonmail.com
Fixes: 7c395ea5 ("Bluetooth: Query LE tx power on startup")
Cc: stable@vger.kernel.org
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Some devices have a bug causing them to not work if they query
LE tx power on startup. Thus we add a quirk in order to not query it
and default min/max tx power values to HCI_TX_POWER_INVALID.
Signed-off-by: NAditya Garg <gargaditya08@live.com>
Reported-by: NOrlando Chamberlain <redecorating@protonmail.com>
Tested-by: NOrlando Chamberlain <redecorating@protonmail.com>
Link:
https://lore.kernel.org/r/4970a940-211b-25d6-edab-21a815313954@protonmail.com
Fixes: 7c395ea5 ("Bluetooth: Query LE tx power on startup")
Cc: stable@vger.kernel.org
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Similar to MT7921 btusb, we enable AOSP extension for MT7921 btmtksdio
as well.
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Enable msft opcode for mt7921 chip.
Signed-off-by: NŁukasz Bartosik <lb@semihalf.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add a USB ID 0489:e0e3 of HP to usb_device_id table for WCN6855.

-Device(0489:e0e3) from /sys/kernel/debug/usb/devices
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e0e3 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:  If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  65 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  65 Ivl=1ms
Signed-off-by: NZijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This change the use of switch statement to a function table which is
easier to extend.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This change the use of switch statement to a function table which is
easier to extend and can include min/max length of each command.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This change the use of switch statement to a function table which is
easier to extend and can include min/max length of each subevent.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This change the use of switch statement to a function table
which is easier to extend and can include min/max length of each HCI
event.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This uses skb_pull_data to check the LE Direct Advertising Report
events received have the minimum required length.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This uses skb_pull_data to check the LE Extended Advertising Report
events received have the minimum required length.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This uses skb_pull_data to check the LE Advertising Report events
received have the minimum required length.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This uses skb_pull_data to check the LE Metaevents received have the
minimum required length.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This uses skb_pull_data to check the Extended Inquiry Result events
received have the minimum required length.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This uses skb_pull_data to check the Inquiry Result with RSSI events
received have the minimum required length.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This uses skb_pull_data to check the Inquiry Result events received
have the minimum required length.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This uses skb_pull_data to check the Number of Complete Packets events
received have the minimum required length.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This uses skb_pull_data to check the Command Complete events received
have the minimum required length.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This uses skb_pull_data to check the BR/EDR events received have the
minimum required length.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Like skb_pull but returns the original data pointer before pulling the
data after performing a check against sbk->len.

This allows to change code that does "struct foo *p = (void *)skb->data;"
which is hard to audit and error prone, to:

        p = skb_pull_data(skb, sizeof(*p));
        if (!p)
                return;

Which is both safer and cleaner.
Acked-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

btmtksdio have to rely on MMC_PM_KEEP_POWER in pm_flags to avoid that
SDIO power is being shut off during the device is in suspend. That fixes
the SDIO command fails to access the bus after the device is resumed.

Fixes: 7f3c563c ("Bluetooth: btmtksdio: Add runtime PM support to SDIO based Bluetooth")
Co-developed-by: NMark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: NMark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Runtime pm ops is not aware the sdio_func status that is probably
being disabled by btmtksdio_close. Thus, we are only able to access the
sdio_func for the runtime pm operations only when the sdio_func is
available.

Fixes: 7f3c563c ("Bluetooth: btmtksdio: Add runtime PM support to SDIO based Bluetooth")
Co-developed-by: NMark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: NMark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Cancel sync commands when transmission of URBs fail. This is done for
both failures to send a command URB and also when the interrupt URB used
to retrieve a response fails.

This approach is sufficient to quickly deal with certain errors such as
a device being disconnected while synchronous commands are done during
initialization.
Signed-off-by: NBenjamin Berg <bberg@redhat.com>
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>

If sending a frame failed any sync command associated with it will never
be completed. As such, cancel any such command immediately to avoid
timing out.
Signed-off-by: NBenjamin Berg <bberg@redhat.com>
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>

After transfer errors it makes sense to cancel an ongoing synchronous
command that cannot complete anymore. To permit this, export the old
hci_req_sync_cancel function as hci_cmd_sync_cancel in the API.
Signed-off-by: NBenjamin Berg <bberg@redhat.com>
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>

Resetting the timers and cmd_cnt means that we assume the device will be
in a good state after the sync command finishes. Without this a chain of
synchronous commands might get stuck if one of them is cancelled.
Signed-off-by: NBenjamin Berg <bberg@redhat.com>
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>

When doing remote name request, we cannot scan. In the normal case it's
OK since we can expect it to finish within a short amount of time.
However, there is a possibility to scan lots of devices that
(1) requires Remote Name Resolve
(2) is unresponsive to Remote Name Resolve
When this happens, we are stuck to do Remote Name Resolve until all is
done before continue scanning.

This patch adds a time limit to stop us spending too long on remote
name request.
Signed-off-by: NArchie Pusaka <apusaka@chromium.org>
Reviewed-by: NMiao-chen Chou <mcchou@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Introducing NAME_REQUEST_FAILED flag that will be sent together with
device found event on name resolve failure. This will provide the
userspace with an information so it can decide not to resolve the
name for these devices in the future.
Signed-off-by: NArchie Pusaka <apusaka@chromium.org>
Reviewed-by: NMiao-chen Chou <mcchou@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

num_keys is actually 2 octects not 1:

BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 4, Part E
page 1989:

  Num_Keys_Deleted:
  Size: 2 octets
  0xXXXX	Number of Link Keys Deleted
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Both max_num_keys and num_key are 2 octects:

BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 4, Part E
page 1985:

  Max_Num_Keys:
  Size: 2 octets
  Range: 0x0000 to 0xFFFF

  Num_Keys_Read:
  Size: 2 octets
  Range: 0x0000 to 0xFFFF
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Check for out-of-bound read was being performed at the end of while
num_reports loop, and would fill journal with false positives. Added
check to beginning of loop processing so that it doesn't get checked
after ptr has been advanced.
Signed-off-by: NBrian Gix <brian.gix@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add the more IDs of HP to usb_device_id table for WCN6855.

-Device(0489:e0cc) from /sys/kernel/debug/usb/devices
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e0cc Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:  If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  65 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  65 Ivl=1ms

-Device(0489:e0d6) from /sys/kernel/debug/usb/devices
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e0d6 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:  If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  65 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  65 Ivl=1ms
Signed-off-by: NTim Jiang <tjiang@codeaurora.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The board ID should be split into two bytes.
The 1st byte is chip ID, and the 2nd byte is platform ID.
For example, board ID 0x010A, 0x01 is platform ID. 0x0A is chip ID.
we have several platforms, and platform IDs are continuously added.
We would not distinguish different chips if we get these mixed up.
Platform ID:
0x00 is for Mobile
0x01 is for X86
0x02 is for Automotive
0x03 is for Consumer electronic
Signed-off-by: NTim Jiang <tjiang@codeaurora.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Realtek RTL8852AE has both wifi and BT components. The latter reports
a USB ID of 0bda:385a, which is not in the table.

The portion of /sys/kernel/debug/usb/devices pertaining to this device is

T:  Bus=01 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0bda ProdID=385a Rev= 0.00
S:  Manufacturer=Realtek
S:  Product=Bluetooth Radio
S:  SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Use the existent variable to drop the unnecessary variable created.
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>