Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.

devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com> (for ocores and mux-gpio)
Acked-by: Havard Skinnemoen <hskinnemoen@gmail.com> (for i2c-gpio)
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn> (for puf3)
Acked-by: Barry Song <baohua.song@csr.com> (for sirf)
Reviewed-by: NJean Delvare <khali@linux-fr.org>
[wsa: Fixed "foo* bar" flaws while we are here]
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

The OMAP_I2C_FLAG_RESET_REGS_POSTIDLE is not used anymore
in the i2c driver. Remove the flag.
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Currently we just queue the transfer and release the
qos constraints, however we do not wait for the transfer
to complete to release the constraint. Move the remove
constraint after the bus busy as we are sure that the
transfers are completed by then.
Acked-by: NJean Pihet <j-pihet@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

Currently after the reset the sysc is written with hardcoded values.
The patch reads the sysc register and writes back the same value
after reset.

- Some unnecessary rev checks can be optimised.
- Also due to whatever reason the hwmod flags are changed
we will not reset the values.
- In some of the cases the minor values of the 2430 register
is different(0x37) in that case the autoidle setting may be missed.
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Currently the restore is done based on the flag
OMAP_I2C_FLAG_RESET_REGS_POSTIDLE.

This helps the following
- The driver is always capable of restoring regardless
of the off mode support being there or not.

- While testing omap2430 it is found that in case of certain
error paths (timeout) a reset is done. However the restore
never happens as it is dependent on the POSTIDLE flag.
The other option would be to call a restore in the reset
case. As there are only a few registers to be restored
the penalty in the idle case should not be much.
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Implement reset as a separate function.
This will enable us to make sure that we don't do the
calculation again on every transfer.
Also at probe the reset is not added as the hwmod is doing that
for us.
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

re-factor omap_i2c_init() so that we can re-use it for resume.
While at it also remove the bufstate variable as we write it
in omap_i2c_resize_fifo for every transfer.
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

The commit [i2c: omap: use revision check for OMAP_I2C_FLAG_APPLY_ERRATA_I207]
uses the revision id instead of the flag. So the flag can be safely removed.
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

The dtrev is used only for the comments. Remove the same and use
the scheme instead to know if it is version2.
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

The errata i207 is enabled for 2430 and 3xxx. Use the revision check
to enable the erratum instead.
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

The revision register on OMAP4 is a 16-bit lo and a 16-bit
hi. Currently the driver reads only the lower 8-bits.
Fix the same by preventing the truncating of the rev register
for OMAP4.

Also use the scheme bit ie bit-14 of the hi register to know if it
is OMAP_I2C_IP_VERSION_2.

On platforms previous to OMAP4 the offset 0x04 is IE register whose
bit-14 reset value is 0, the code uses the same to its advantage.

Also since the omap_i2c_read_reg uses reg_map_ip_* a raw_readw is done
to fetch the revision register.

The dev->regs is populated after reading the rev_hi. A NULL check
has been added in the resume handler to prevent the access before
the setting of the regs.
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Some GPIO expanders need some early pin control muxing. Due to
legacy boards sometimes the driver uses subsys_initcall instead of
module_init. This patch takes advantage of defer probe feature
and pin control in order to wait until pin control probing before
GPIO driver probing. It has been tested on OMAP5 board with TCA6424
driver.
Signed-off-by: NSebastien Guiriec <s-guiriec@ti.com>
Acked-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

if we allow compiler reorder our writes, we could
fall into a situation where dev->buf_len is reset
for no apparent reason.

This bug was found with a simple script which would
transfer data to an i2c client from 1 to 1024 bytes
(a simple for loop), when we got to transfer sizes
bigger than the fifo size, dev->buf_len was reset
to zero before we had an oportunity to handle XDR
Interrupt. Because dev->buf_len was zero, we entered
omap_i2c_transmit_data() to transfer zero bytes,
which would mean we would just silently exit
omap_i2c_transmit_data() without actually writing
anything to DATA register. That would cause XDR
IRQ to trigger forever and we would never transfer
the remaining bytes.

After adding the memory barrier, we also drop resetting
dev->buf_len to zero in omap_i2c_xfer_msg() because
both omap_i2c_transmit_data() and omap_i2c_receive_data()
will act until dev->buf_len reaches zero, rendering the
other write in omap_i2c_xfer_msg() redundant.

This patch has been tested with pandaboard for a few
iterations of the script mentioned above.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

if we allow compiler reorder our writes, we could
fall into a situation where dev->buf_len is reset
for no apparent reason.

This bug was found with a simple script which would
transfer data to an i2c client from 1 to 1024 bytes
(a simple for loop), when we got to transfer sizes
bigger than the fifo size, dev->buf_len was reset
to zero before we had an oportunity to handle XDR
Interrupt. Because dev->buf_len was zero, we entered
omap_i2c_transmit_data() to transfer zero bytes,
which would mean we would just silently exit
omap_i2c_transmit_data() without actually writing
anything to DATA register. That would cause XDR
IRQ to trigger forever and we would never transfer
the remaining bytes.

After adding the memory barrier, we also drop resetting
dev->buf_len to zero in omap_i2c_xfer_msg() because
both omap_i2c_transmit_data() and omap_i2c_receive_data()
will act until dev->buf_len reaches zero, rendering the
other write in omap_i2c_xfer_msg() redundant.

This patch has been tested with pandaboard for a few
iterations of the script mentioned above.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

This reverts commit 3db11fef
(ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints).
This commit causes I2C timeouts to appear on several OMAP3430/3530-based
boards:

  http://marc.info/?l=linux-arm-kernel&m=135071372426971&w=2
  http://marc.info/?l=linux-arm-kernel&m=135067558415214&w=2
  http://marc.info/?l=linux-arm-kernel&m=135216013608196&w=2

and appears to have been sent for merging before one of its prerequisites
was merged:

  http://marc.info/?l=linux-arm-kernel&m=135219411617621&w=2Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Acked-by: NJean Pihet <j-pihet@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

This reverts commit 3db11fef
(ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints).
This commit causes I2C timeouts to appear on several OMAP3430/3530-based
boards:

  http://marc.info/?l=linux-arm-kernel&m=135071372426971&w=2
  http://marc.info/?l=linux-arm-kernel&m=135067558415214&w=2
  http://marc.info/?l=linux-arm-kernel&m=135216013608196&w=2

and appears to have been sent for merging before one of its prerequisites
was merged:

  http://marc.info/?l=linux-arm-kernel&m=135219411617621&w=2Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Acked-by: NJean Pihet <j-pihet@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Convert the driver from the outdated omap_pm_set_max_mpu_wakeup_lat
API to the new PM QoS API.
Since the constraint is on the MPU subsystem, use the PM_QOS_CPU_DMA_LATENCY
class of PM QoS. The resulting MPU constraints are used by cpuidle to
decide the next power state of the MPU subsystem.

The I2C device latency timing is derived from the FIFO size and the
clock speed and so is applicable to all OMAP SoCs.
Signed-off-by: NJean Pihet <j-pihet@ti.com>
Acked-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

When booting using a device tree, the adapter number is dynamically
assigned after the log message is sent.
This patch modifies the log message to get a correct adapter id.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Tested-by: NBenoit Cousson <b-cousson@ti.com>
Acked-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

move the goto out label one line down, so that
it can be used when stat is read as zero. All
other exits, can be done with a break statement.

While at that, also break out as soon as we
complete draining IRQ, since at that time
we know we transferred everything there was
to be transferred.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

this helps us reduce unnecessary pm transitions
in case we have another i2c message starting soon.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

before starting any messages we call pm_runtime_get_sync()
which will make sure that by the time we program a transfer
and our IRQ handler gets called, we're not suspended
anymore.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

for OMAP2, we can easily switch over to threaded
IRQs on the I2C driver. This will allow us to
spend less time in hardirq context.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
[Trivial formating changes]
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Currently omap_i2c_ack_stat doesn't use the stat variable.
After the read of the I2C_STAT_REG it is not used.
Remove the redundant read of the status register.
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

we can ack stat and complete the command from
the errata handling itself.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

This patch will try to avoid the usage of
draining feature by reconfiguring the FIFO
the start condition of each message based
on the message's size.

By doing that, we will be better utilizing
the FIFO when doing big transfers.

While at that also drop the now unneeded
check for dev->buf_len as we always know
the amount of data to be transmitted.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

instead of having multiple return points, use
a goto statement to make that clearer.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Always return IRQ_HANDLED otherwise we could get our IRQ line disabled due
to many spurious IRQs.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
[Trivial changes to commitlogs]
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

omap_i2c_dev is allocated with kzalloc(),
so we need not initialize b_hw to zero.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

that way we can ignore TX IRQs while in receiver
mode and ignore RX IRQs while in transmitter mode.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
[Remove unnecessary braces]
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

that's a nice helper from drivers core which
will give us the exact IRQ number, instead
of a pointer to an IRQ resource.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

According to flow diagrams on OMAP TRMs,
we should ACK the IRQ as they happen.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
[Ack the stat OMAP_I2C_STAT_AL in case of arbitration lost]
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

this will make sure that we execute at least once.
No functional changes otherwise.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

re-factor the common parts to a separate function,
so that code is easier to read and understand.

No functional changes.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Make it not depend on ISR's local variables
in order to make it easier to re-factor the
transmit data loop.
Also since we are waiting for XUDF(Transmitter underflow) just before
writing data lets not flag the underflow.
This is anyways going to go once we write
the data.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

While they do pretty much the same thing, there
are a few peculiarities. Specially WRT erratas,
it's best to split those out and re-factor the
read/write loop to another function which both
cases call.

This last part will be done on another patch.

While at that, also avoid an unncessary register
read since dev->fifo_len will always contain the
correct amount of data to be transferred.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

stat & BIT(1) is the same as BIT(1), so let's
simplify things a bit by removing "stat &" from
all omap_i2c_ack_stat() calls.

Code snippet (extremely simplified):

if (stat & NACK) {
        ...
        omap_i2c_ack_stat(dev, stat & NACK);
}

if (stat & RDR) {
        ...
        omap_i2c_ack_stat(dev, stat & RDR);
}

and so on. The tricky place is only WRT errata handling, for example:

if (*stat & (NACK | AL)) {
        omap_i2c_ack_stat(dev, *stat & (XRDY | XDR));
        ...
}

but in this case, the errata says we must clear XRDY and XDR if that
errata triggers, so if they just got enabled or not, it doesn't matter.

Another tricky place is RDR | RRDY (likewise for XDR | XRDY):

if (stat & (RDR | RRDY)) {
        ...
        omap_i2c_ack_stat(dev, stat & (RDR | RRDY));
}

again here there will be no issues because those IRQs never fire
simultaneously and one will only after after we have handled the
previous, that's because the same FIFO is used anyway and we won't shift
data into FIFO until we tell the IP "hey, I'm done with the FIFO, you
can shift more data"
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Reviewed-by : Santosh Shilimkar <santosh.shilimkar@ti.com>
[Added the explaination from the discurssion to the commit logs]
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

trivial patch to aid readability. No functional
changes.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

The patch intends to decrease the indentation level on the
data handling
by using the fact that else of if (dev->buf_len) is same as
if (!dev->buf_len)

if (dev->buf_len) {
	aaa;
} else {
	bbb;
	break;
}

to

if (!dev->buf_len) {
        bbb;
        break;
}
aaa;

Hence no functional changes.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Reviewed-by : Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>