Signed-off-by: NSimon Guinot <sguinot@lacie.com>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

This patch add a LED class driver for the dual-GPIO LEDs found on the
Network Space v2 board (and parents). This include Internet Space v2,
Network Space (Max) v2 and d2 Network v2 boards.

This dual-GPIO LED is wired to a CPLD and can blink in relation with the
SATA activity. The driver expose this capability through a "sata" sysfs
attribute.
Signed-off-by: NSimon Guinot <sguinot@lacie.com>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

Soekris net5501 is x86 only and cleanup some undeeded dependencies
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

This add basic led support for Freescale MC13783 PMIC.
Signed-off-by: NPhilippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

It is based on the previously submitted code by Alessandro Zummo, but is
changed to use the new GPIO driver with 2.6.33, and the driver has been
moved to drivers/leds where it belongs.

[akpm@linux-foundation.org: coding-style fixes]
[randy.dunlap@oracle.com: fix net5501 kconfig]
Signed-off-by: NBjarke Istrup Pedersen <gurligebis@gentoo.org>
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAlessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

This patch adds an LED driver to support the Dell Activity LED on the
Dell Latitude 2100 netbook and future products to come. The Activity LED
is visible externally in the lid so classroom instructors can observe it
from a distance. The driver uses the sysfs led_class and provides a
standard LED interface.

Signed-off by: Bob Rodgers <Robert_Rodgers@dell.com>
Signed-off-by: NLouis Davis <Louis_Davis@dell.com>
Signed-off-by: Jim Dailey <Jim_Dailey@dell.com>, Developers
Acked-by: NMatthew Garrett <mjg@redhat.com>
Acked-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Remove the need for "depends on LEDS_CLASS" by wrapping the affected
config options in an if/endif block. Similar for "depends on LEDS_TRIGGERS".

LEDS_COBALT_RAQ still has a "depends on LEDS_CLASS=y" since it cannot
be selected to build as a module.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

The ALIX2 LED driver and the CS5535 GPIO drivers share the same I/O
range which causes a conflict if they're both enabled. Fix this for now
by adding Kconfig dependencies. While at it, also drop the EXPERIMENTAL
flag, as the code has been around for awhile already.

Note that this is a hack. At some point, a real platform support for
this board should be added which handles the LEDs via the leds-gpio
driver.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Enable led sub device in Marvell 88PM860x. Two LED arrays can be supported.
Each LED array can be used for R,G,B leds.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This driver provides an interface for controlling LEDs (or vibrators)
connected to PMICs for which there is a regulator framework driver.

This driver can be used, for instance, to control vibrator on all Motorola EZX
phones using the pcap-regulator driver services.
Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

The LT3593 is a step-up DC/DC converter designed to drive up to ten
white LEDs in series. The current flow can be set with a control pin.

This driver controls any number of such devices connected on generic
GPIOs and exports the function as as platform_driver.

The gpio_led platform data struct definition is reused for this purpose.

Successfully tested on a PXA embedded board.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

This code is based on a driver that came in the "Open-source
and GPL components" download here:

http://downloadcenter.intel.com/SearchResult.aspx?lang=eng&ProductFamily=Server+Products&ProductLine=Intel%C2%AE+Storage+Systems&ProductProduct=Intel%C2%AE+Entry+Storage+System+SS4200-E&OSVersion=OS+Independent

It was in a file called nasgpio.c inside of a second zip file
called SS4200-E_Linux_SIO_Driver-v1.4.zip and is based on this
updated to use the LED subsystem with the ioctl and hardware
monitor support removed.

I don't have any need for brightness
control, and its code is *completely* separate from the on/off
controls implemented here.  If anyone else wants it, I'd be
happy to look into adding it, but I don't care enough for now.

Except for the probe routines, I rewrote most of it.  I also
Note that I don't have any hardware documentation except for
the original driver.

Thanks go to Arjan for his help in getting the original source
for this released and for chasing down some licensing issues.
Signed-off-by: NDave Hansen <dave@sr71.net>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

The WM831x devices feature two software controlled status LEDs with
hardware assisted blinking.

The device can also autonomously control the LEDs based on a selection
of sources.  This can be configured at boot time using either platform
data or the chip OTP.  A sysfs file in the style of that for triggers
allowing the control source to be configured at run time.  Triggers
can't be used here since they can't depend on the implementation details
of a specific LED type.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

LEDs driver for National Semiconductor LP3944 Funlight Chip
http://www.national.com/pf/LP/LP3944.html

This helper chip can drive up to 8 leds, with two programmable DIM
modes; it could even be used as a gpio expander but this driver assumes
it is used as a led controller.

The DIM modes are used to set _blink_ patterns for leds, the pattern is
specified supplying two parameters:
  - period: from 0s to 1.6s
  - duty cycle: percentage of the period the led is on, from 0 to 100

LP3944 can be found on Motorola A910 smartphone, where it drives the rgb
leds, the camera flash light and the displays backlights.
Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Remove an orphan Kconfig entry (LEDS_LP5521)
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Add initialisation of GPIO ports for compatibility with boards with Award
BIOS (e.g.  ALIX.3D3).
Signed-off-by: NTobias Mueller <Tobias_Mueller@twam.info>
Reviewed-by: NConstantin Baranov <const@mimas.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

LP5521 is a three channel led driver with support
for hardware accelerated patterns (currently used
via lp5521-only sysfs interface).

Currently, it's used on n810 device.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

ROHM BD2802GU is a RGB LED controller attached to i2c bus and specifically
engineered for decoration purposes.  This RGB controller incorporates
lighting patterns and illuminates.

This driver is designed to minimize power consumption, so when there is no
emitting LED, it enters to reset state.  And because the BD2802GU has lots
of features that can't be covered by the current LED framework, it
provides Advanced Configuration Function(ADF) mode, so that user
applications can set registers of BD2802GU directly.

Here are basic usage examples :
; to turn on LED (not blink)
$ echo 1 > /sys/class/leds/led1_R/brightness
; to blink LED
$ echo timer > /sys/class/leds/led1_R/trigger
$ echo 1 > /sys/class/leds/led1_R/delay_on
$ echo 1 > /sys/class/leds/led1_R/delay_off
; to turn off LED
$ echo 0 > /sys/class/leds/led1_R/brightness

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NKim Kyuwon <chammoru@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

The leds-clevo-mail driver is in the mainline kernel since 2.6.25 and works
without severe problems. Make this driver available for a larger audience.
Signed-off-by: NMárton Németh <nm127@freemail.hu>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

The gpio led trigger will allow leds to be triggered by
gpio events.

When we give the led a gpio number, the trigger will
request_irq() on that so we don't have to keep polling
for gpio state.

It's useful for usecases as n810's keypad leds that could
be triggered by the gpio event generated when user slides
up to show the keypad.

We also provide means for userland to tell us what is the
desired brightness for that special led when it goes on
so userland could use information from ambient light sensors
and not set led brightness too high if it's not necessary.
Signed-off-by: NFelipe Balbi <me@felipebalbi.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Mikrotik built six LEDs into the Routerboard 532, from which one is
destined for custom use, the so called "User LED". This patch adds a
driver for it, based on the LEDs class.
Signed-off-by: NPhil Sutter <n0-1@freewrt.org>
Acked-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Add a simple driver for pwm driver LEDs.  pwm_id and period can be defined
in board file.  It is developed for pxa, however it is probably generic
enough to be used on other platforms with pwm.
Signed-off-by: NLuotao Fu <l.fu@pengutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Add an LED driver using the DAC124S085 DAC from NatSemi

[randy.dunlap@oracle.com: use header files for interfaces]
Signed-off-by: NGuennadi Liakhovetski <lg@denx.de>
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Add bindings to support LEDs defined as of_platform devices in addition to
the existing bindings for platform devices.

New options in Kconfig allow the platform binding code and/or the
of_platform code to be turned on.  The of_platform code is of course only
available on archs that have OF support.

The existing probe and remove methods are refactored to use new functions
create_gpio_led(), to create and register one led, and delete_gpio_led(),
to unregister and free one led.  The new probe and remove methods for the
of_platform driver can then share most of the common probe and remove code
with the platform driver.

The suspend and resume methods aren't shared, but they are very short.  The
actual led driving code is the same for LEDs created by either binding.

The OF bindings are based on patch by Anton Vorontsov
<avorontsov@ru.mvista.com>.  They have been extended to allow multiple LEDs
per device.
Signed-off-by: NTrent Piepho <tpiepho@freescale.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NSean MacLennan <smaclennan@pikatech.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Signed-off-by: NMatt LaPlante <kernel1@cyberdogtech.com>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Kernel module providing implementation of LED netfilter target.  Each
instance of the target appears as a led-trigger device, which can be
associated with one or more LEDs in /sys/class/leds/
Signed-off-by: NAdam Nielsen <a.nielsen@shikadi.net>
Acked-by: NRichard Purdie <rpurdie@linux.intel.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>

Move the second part of the HP laptop disk protection functionality (a red
led) to the same driver.  From a purely Linux developer's point of view,
the led and the accelerometer have nothing related.  However, they
correspond to the same ACPI functionality, and so will always be used
together, moreover as they share the same ACPI PNP alias, there is no
other simple to allow to have same loaded at the same time if they are not
in the same module.  Also make it requires the led class to compile and
update the Kconfig text.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The voltage and current regulators on the WM8350 AudioPlus PMIC can be
used in concert to provide a power efficient LED driver.  This driver
implements support for this within the standard LED class.

Platform initialisation code should configure the LED hardware in the
init callback provided by the WM8350 core driver.  The callback should
use wm8350_isink_set_flash(), wm8350_dcdc25_set_mode() and
wm8350_dcdc_set_slot() to configure the operating parameters of the
regulators for their hardware and then then use wm8350_register_led() to
instantiate the LED driver.

This driver was originally written by Liam Girdwood, though it has been
extensively modified since then.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Cobalt Raq LEDs require LEDS_CLASS=y.
Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Driver for PC Engines ALIX.2 and ALIX.3 LEDs.
Signed-off-by: NConstantin Baranov <const@mimas.ru>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

HP notebooks contain accelerometer-based disk protection subsystem,
and LED that indicates hard disk is protected. This is driver for the
LED part.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

The cm-x270 board uses leds-gpio so remove the now unneeded driver.
Acked-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

This allows LEDs to be controlled as a backlight device where
they turn off and on when the display is blanked and unblanked.
This is useful where you need various key backlight LEDs to
dim at the same time as the backlight.
Signed-off-by: NRodolfo Giometti <giometti@linux.it>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

* Add struct ide_disk_ops containing protocol specific methods.

* Add 'struct ide_disk_ops *' to ide_drive_t.

* Convert ide-{disk,floppy} drivers to use struct ide_disk_ops.

* Merge ide-{disk,floppy} drivers into generic ide-gd driver.

While at it:
- ide_disk_init_capacity() -> ide_disk_get_capacity()
Acked-by: NBorislav Petkov <petkovbb@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Now as the scoop pins are covered by the generic gpio API,
we can use leds-gpio driver instead of special leds-spitz

Drop leds-spitz.c and the declarations of now un-referenced
spitzscoop_device, spitzscoop2_device.
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Now as the scoop pins are covered by the generic gpio API,
we can use leds-gpio driver instead of special leds-corgi

Drop leds-corgi.c and remove the declaration of now un-referenced
corgiscoop_device.
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>