The commit 9a763bfb "get rid of mxc_gpio_init" changed gpio_init
and irq_init sequence. Usually we will call set_irq_chained_handler
in gpio_init functions, this should be called after the irq_init
called, otherwise the chained irq can't get propoer irq_chip and this
irq will remain masked even we called set_irq_chained_handler.
Signed-off-by: NJason Wang <jason77.wang@gmail.com>
Tested-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

as per suggested by Sascha
Signed-off-by: NEric Bénard <eric@eukrea.com>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch fixes the following Kconfig warning :
"arch/arm/mach-mx25/Kconfig:18:warning: choice value used outside its
choice group
Signed-off-by: NEric Bénard <eric@eukrea.com>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NEric Bénard <eric@eukrea.com>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

In order to make this patch compile, even if the flexcan driver with
it's header defining the platform data isn't merged yet, two ifdefs have
been added. They effect that the "imx_add_flexcan" function results in a
no-op function if the driver hasn't been activated.

These ifdefs can be removed after the flexcan driver has been merged.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The i.MX51 generates 2 IRQ for each GPIO bank : one for gpio 0 to 15
and one for gpio 16 to 31.
Actually only the lower IRQ is registered so register the second one.
Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

the i2c_board_info structure landed into the SPI #if/#endif
which is wrong.
Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

DEBUG_LL is actually broken on i.MX25, this patch fix it.
Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NEric Bénard <eric@eukrea.com>
Cc: s.hauer@pengutronix.de
Cc: linux-mmc@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Add keymaps and imx_keypad device registration for imx51_3ds board.
Signed-off-by: NJason Wang <jason77.wang@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

add imx_keypad platform device definition and clocks for mx51
platforms.
Signed-off-by: NJason Wang <jason77.wang@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

3-stack is a reference board from Freescale for their i.MX51 SoC.

Add board definition, Kconfig and Makefile to enable Freescale 3-stack
board.

Boot tested on a i.MX51 3-stack Rev2.0 board
Signed-off-by: NJason Wang <jason77.wang@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

mx27_3ds: add support for the keypad
Signed-off-by: NRogerio Pimentel <rogerio.pimentel@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Because we add a 3ds debug board support in mxc level, we remove
those redundant codes from board level.
Signed-off-by: NJason Wang <jason77.wang@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The debug board is little different for all mxc 3-stack(PDK)
platforms, it is possible here to add a common implementation to
support this board.
Signed-off-by: NJason Wang <jason77.wang@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

There are some more conflicts than detected by git, namely support for
the newly added cpuimx machines needed to be converted to dynamic device
registration.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Conflicts:
	arch/arm/mach-imx/Makefile
	arch/arm/mach-imx/devices.c
	arch/arm/mach-imx/devices.h
	arch/arm/mach-imx/eukrea_mbimx27-baseboard.c
	arch/arm/mach-mx2/Kconfig
	arch/arm/mach-mx25/Makefile
	arch/arm/mach-mx25/devices.c
	arch/arm/plat-mxc/include/mach/mx25.h
	arch/arm/plat-mxc/include/mach/mxc_nand.h

Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

cleaned up some duplicated mxc_gpio_mode calls and move the correpsonding
pin multiplexing either into the initial pin config table or ifdef blocks.
Signed-off-by: NLuotao Fu <l.fu@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

this one adds the frambuffer device and a TFT panel to the PhyCard-S
(pca100) board.
Signed-off-by: NLuotao Fu <l.fu@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

These GPIO bank offsets are useful when define a gpio number.
E.G. when GPIO PORTC pin 6 is used for irq request pin of external
expanding device, we can define it like:
  #define EXP_PARENT_IRQ_PIN (GPIO_PORTC + 6)
Signed-off-by: NJason Wang <jason77.wang@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Add UART2 CTS/RTS and UART3 RXD/TXD pad definitons for imx51_3ds board,
add GPIO_1_6 definiton because this pin is used as a CPLD parent irq
request pin on imx51_3ds board.
Signed-off-by: NJason Wang <jason77.wang@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

For pad EIM_D27 to work in UART3_RTS mode, the input path should be
3 instead of 0; for pad USBH1_STP to work in GPIO_1_27 mode, the mux
value should be 2 instead of 8.
Signed-off-by: NJason Wang <jason77.wang@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The pads capable of being used as GPIOs had their pad-name and mode-name
switched. Also, fix the following:

- Whitespace fixes
- Replace IOMUX_CONFIG_ALTn with 'n'
Signed-off-by: NAmit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

* cpuimx35 integrates i.MX35, RAM, NAND, Ethernet, I2C RTC, USB Host,
USB OTG and I2C touchscreen controller
* mbimxsd provides access to LCD, Audio, LED, Switch button, UART ...
Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The information in the i.MX25 Reference Manual is lacking. Add information from
the Freescale BSP.
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Reviewed-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Reviewed-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

* cpuimx25 integrates i.MX25, RAM, NAND, Ethernet, I2C RTC, USB Host
and USB OTG
* mbimxsd provides access to LCD, Audio, LED, Switch button, UART ...
Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

* add clocks for audmux and ssi 1 & 2
* add irq for ssi 1 & 2
* add devices platform for ssi1 & 2
* update audmux-v2 for i.MX25
* add base addresses for audmux & ssi 1 & 2
* add iomux configuration for GPIO for AUD5 port
Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>