Based on the hardware spec, the BDW GT3 machine has two independent
BSD ring that can be used to dispatch the video commands.
So just initialize it.

V3->V4: Follow Imre's comment to do some minor updates. For example:
more comments are added to describe the semaphore between ring.
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
[danvet: Fix up checkpatch error.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Even without enabling the ringbuffers to allow command execution, we can
still control the display engines to enable modesetting. So make the
ringbuffer initialization failure soft, and mark the GPU as wedged
instead.

v2: Only treat an EIO from ring initialisation as a soft failure, and
abort module load for any other failure, such as allocation failures.

v3: Add an *ERROR* prior to declaring the GPU wedged so that it stands
out like a sore thumb in the logs
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NOscar Mateo <oscar.mateo@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Tearing down the ring buffers across resume is overkill, risks
unnecessary failure and increases fragmentation.

After failure, since the device is still active we may end up trying to
write into the dangling iomapping and trigger an oops.

v2: stop_ringbuffers() was meant to call stop(ring) not
cleanup(ring) during resume!
Reported-by: NJae-hyeon Park <jhyeon@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=72351
References: https://bugs.freedesktop.org/show_bug.cgi?id=76554Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NOscar Mateo <oscar.mateo@intel.com>
[danvet: s/ring->obj == NULL/!intel_ring_initialized(ring)/ as
suggested by Oscar.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Unfortunately this requires a drm-wide change, and I didn't see a sane
way around that. Luckily it's fairly simple, we just need to inline
the respective get_irq implementation from either drm_pci.c or
drm_platform.c.

With that we can now also remove drm_dev_to_irq from drm_irq.c.
Reviewed-by: NThierry Reding <treding@nvidia.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The dev->struct_mutex locking in drm_irq.c only protects
dev->irq_enabled. Which isn't really much at all and only prevents
especially nasty ums userspace from concurrently installing the
interrupt handling a few times. Or at least trying.

There are tons of unlocked readers of dev->irqs_enabled in the vblank
wait code (and by extension also in the pageflip code since that uses
the same vblank timestamp engine).

Real modesetting drivers should ensure that nothing can go haywire
with a sane setup teardown sequence. So we only really need this for
the drm_control ioctl, everywhere else this will just paper over
nastiness.

Note that drm/i915 is a bit specially due to the gem+ums combination.
So there we also need to properly protect the entervt and leavevt
ioctls. But it's definitely saner to do everything in one go than to
drop the lock in-between.

Finally there's the gpu reset code in drm/i915. That one's just race
(concurrent userspace calls to for vblank waits of pageflips could
spuriously fail). So wrap it up in with a nice comment since fixing
this is more involved.

v2: Rebase and fix commit message (Thierry)
Reviewed-by: NThierry Reding <treding@nvidia.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If we always initialize kref for the context, even if we are using fake
contexts for hangstats when there is no hw support, we can forgo the
dance to dereference the ctx->obj and inspect whether we are permitted
to use kref inside i915_gem_context_reference() and _unreference().

My ulterior motive here is to improve the debugging of a use-after-free
of ctx->obj. This patch avoids the dereference here and instead forces
the assertion checks associated with kref.

v2: Refactor the fake contexts to being even more like the real
contexts, so that there is much less duplicated and special case code.

v3: Tweaks.
v4: Tweaks, minor.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76671Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Tested-by: Nlu hua <huax.lu@intel.com>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
[Jani: tiny change to backport to drm-intel-fixes.]
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Piglit runner and QA are both looking at the dmesg for
DRM_ERRORs with test cases. Add a flag to control those
when we they are expected from related test cases.

Also add flag to control if contexts should be banned
that introduced the hang. Hangcheck is timer based and
preventing bans by adding sleeps to testcases makes
testing slower.

v2: intel_ring_stopped(), readable comment (Chris)
v3: keep compatibility (Daniel)

References: https://bugs.freedesktop.org/show_bug.cgi?id=75876Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Clients like i915 need to segregate cache domains within the GTT which
can lead to small amounts of fragmentation. By allocating the uncached
buffers from the bottom and the cacheable buffers from the top, we can
reduce the amount of wasted space and also optimize allocation of the
mappable portion of the GTT to only those buffers that require CPU
access through the GTT.

For other drivers, allocating small bos from one end and large ones
from the other helps improve the quality of fragmentation.

Based on drm_mm work by Chris Wilson.

v3: Changed to use a TTM placement flag
v2: Updated kerneldoc

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Christian König <deathsimple@vodafone.de>
Signed-off-by: NLauri Kasanen <cand@gmx.com>
Signed-off-by: NDavid Airlie <airlied@redhat.com>

No functional changes.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On non-LLC platforms, when changing the cache level of an object, we may
need to unbind it so that prefetching across page boundaries does not
cross into a different memory domain. This requires us to unbind
conflicting vma, but we did so iterating over the objects vma in an
unsafe manner (as the list was being modified as we iterated).

The regression was introduced in
commit 3089c6f2
Author: Ben Widawsky <ben@bwidawsk.net>
Date:   Wed Jul 31 17:00:03 2013 -0700

    drm/i915: make caching operate on all address spaces
apparently as far back as v3.12-rc1, but it has only just begun to
trigger real world bug reports.
Reported-and-tested-by: NNikolay Martynov <mar.kolya@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76384Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When other platforms add runtime PM support they will also need to
disable interrupts, so move the variable to the runtime PM struct.

Also notice that the longer-term goal is to completely kill the
regsave struct, and I even have patches for that.

v2: - Rebase.
v3: - Rebase.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

DRM drivers share a common address_space across all character-devices of a
single DRM device. This allows simple buffer eviction and mapping-control.
However, DRM core currently waits for the first ->open() on any char-dev
to mark the underlying inode as backing inode of the device. This delayed
initialization causes ugly conditions all over the place:
  if (dev->dev_mapping)
    do_sth();

To avoid delayed initialization and to stop reusing the inode of the
char-dev, we allocate an anonymous inode for each DRM device and reset
filp->f_mapping to it on ->open().
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>

When we change the cache_level for an object we need to make sure
we don't put differing types of snoopable memory too close to each
other on non-LLC machines.

Currently i915_gem_object_set_cache_level() will stop looking when
it finds just one vma that has such a conflict. Drop the bogus break
statement to make sure it will unbind all vmas which need to be moved
around to avoid the conflict.

I suppose this is a theoretical issue as currently we don't enable
ppgtt on non-LLC machines, so each object can only have one vma.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We don't always want to write into main memory with pwrite. The shmem
fast path in particular is used for memory that is cacheable - under
such circumstances forcing the cache eviction is undesirable. As we will
always flush the cache when targeting incoherent buffers, we can rely on
that second pass to apply the cache coherency rules and so benefit from
in-cache copies otherwise.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NBrad Volkin <bradley.d.volkin@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We used to lock individual pages inside the buffer object and so needed
to update the page flags every time. However, we now pin the pages into
the object for the duration of the pwrite/pread (and hopefully much
longer) and so we can forgo the flag updates until we release all the
pages.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NBrad Volkin <bradley.d.volkin@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The command parser is going to need the same synchronization and
setup logic, so factor it out for reuse.

v2: Add a check that the object is backed by shmem
Signed-off-by: NBrad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Its last usage outside of i915_gem.c was removed in:

  commit 1f70999f
  Author: Chris Wilson <chris@chris-wilson.co.uk>
  Date:   Mon Jan 27 22:43:07 2014 +0000

     drm/i915: Prevent recursion by retiring requests when the ring is full
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

After finding the guilty batch and request, we can use it to find the
process that submitted the batch and then add the culprit into the error
state.

This is a slightly different approach from Ben's in that instead of
adding the extra information into the struct i915_hw_context, we use the
information already captured in struct drm_file which is then referenced
from the request.

v2: Also capture the workaround buffer for gen2, so that we can compare
    its contents against the intended batch for the active request.

v3: Rebase (Mika)
v4: Check for null context (Chris)
    checkpatch warnings fixed

Link: http://lists.freedesktop.org/archives/intel-gfx/2013-August/032280.html
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v2)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> (v4)
Acked-by: NBen Widawsky <ben@bwidawsk.net>
Cc: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In the past, it was possible to have multiple batches per request due to
a stray signal or ENOMEM. As a result we had to scan each active object
(filtered by those having the COMMAND domain) for the one that contained
the ACTHD pointer. This was then made more complicated by the
introduction of ppgtt, whereby ACTHD then pointed into the address space
of the context and so also needed to be taken into account.

This is a fairly robust approach (though the implementation is a little
fragile and depends upon the per-generation setup, registers and
parameters). However, due to the requirements for hangstats, we needed a
robust method for associating batches with a particular request and
having that we can rely upon it for finding the associated batch object
for error capture.

If the batch buffer tracking is not robust enough, that should become
apparent quite quickly through an erroneous error capture. That should
also help to make sure that the runtime reporting to userspace is
robust. It also means that we then report the oldest incomplete batch on
each ring, which can be useful for determining the state of userspace at
the time of a hang.

v2: Use i915_gem_find_active_request (Mika)

v3: remove check for ring->get_seqno, split long lines (Ben)

v4: check that context is available (Chris)
    checkpatch warnings fixed

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> (v3)
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (v3)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In place of true activity counting, we walk the list of vma associated
with an object managing each on the vm's active/inactive list everytime
we call move-to-inactive. This depends upon the vma->mm_list being
cleared after unbinding, or else we run into difficulty when tracking
the object in multiple vm's - we see a use-after free and corruption of
the mm_list.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If we've explicitly stopped the rings for testing purposes, don't ban
the default context. Fixes kms_flip hang tests.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We currently call intel_mark_idle() too often, as we do so as a
side-effect of processing the request queue. However, we the calls to
intel_mark_idle() are expected to be paired with a call to
intel_mark_busy() (or else we try to idle the hardware by accessing
registers that are already disabled). Make the idle/busy tracking
explicit to prevent the multiple calls.

v2: We can drop some of the complexity in __i915_add_request() as
queue_delayed_work() already behaves as we want (not requeuing the item
if it is already in the queue) and mark_busy/mark_idle imply that the
idle task is inactive.

v3: We do still need to cancel the pending idle task so that it is sent
again after the current busy load completes (not in the middle of it).
Reported-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

One side-effect of the introduction of ppgtt was that we needed to
rebind the object into the appropriate vm (and global gtt in some
peculiar cases). For simplicity this was done twice for every object on
every call to execbuffer. However, that adds a tremendous amount of CPU
overhead (rewriting all the PTE for all objects into WC memory) per
draw. The fix is to push all the decision about which vm to bind into
and when down into the low-level bind routines through hints rather than
performing the bind unconditionally in the execbuffer routine.

Note that this is a regression introduced in the full ppgtt feature
branch, before this we've only done re-bound objects when the relevant
has_(aliasing_ppgtt|global_gtt)_mapping flag was clear. But since
that's per-object and not per-vma that optimization broke.

v2: Split out prep work and unrelated changes.

v3: Bring back functional change around PIN_GLOBAL that I've
accidentally split out.

v4: Remove the temporary hack for the old binding logic to avoid
bisection issues.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=72906
Tested-by: jianx.zhou@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is prep work for reworking the object_pin logic. Atm
it still does a (now redundant) lookup of the vma. The next
patch will fix this.

Split out from Chris vma-bind rework.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Split out from Chris vma-bind rework.

Jani wondered why this is save, and the reason is that i915_vma_unbind
does all these checks, too. So they're redundant.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With abitrary pin flags it makes sense to split out a "please bind
this into global gtt" from the "please allocate in the mappable
range".

Use this unconditionally in our global gtt pin helper since this is
what its callers want. Later patches will drop PIN_MAPPABLE where it's
not strictly needed.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Anything more than just one bool parameter is just a pain to read,
symbolic constants are much better.

Split out from Chris' vma-binding rework patch.

v2: Undo the behaviour change in object_pin that Chris spotted.

v3: Split out misplaced hunk to handle set_cache_level errors,
spotted by Jani.

v4: Keep the current over-zealous binding logic in the execbuffer code
working with a quick hack while the overall binding code gets shuffled
around.

v5: Reorder the PIN_ flags for more natural patch splitup.

v6: Pull out the PIN_GLOBAL split-up again.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Arjan van de Ven reported that on his test machine that he was seeing
stalls of greater than 1 frame greatly impacting the user experience. He
tracked this down to being the locked flush during a pagefault as being
the culprit hogging the struct_mutex and so blocking any other user from
proceeding. Stalling on a pagefault is bad behaviour on userspace's
part, for one it means that they are ignoring the coherency rules on
pointer access through the GTT, but fortunately we can apply the same
trick as the set-to-domain ioctl to do a lightweight, nonblocking flush
of outstanding rendering first.

"Prior to the patch it looks like this
(this one testrun does not show the 20ms+ I've seen occasionally)

  4.99 ms     2.36 ms    31360  __wait_seqno i915_wait_seqno i915_gem_object_wait_rendering i915_gem_object_set_to_gtt_domain i915_gem_fault __do_fault handle_
+pte_fault handle_mm_fault __do_page_fault do_page_fault page_fault
   4.99 ms     2.75 ms   107751  __wait_seqno i915_gem_wait_ioctl drm_ioctl i915_compat_ioctl compat_sys_ioctl ia32_sysret
   4.99 ms     1.63 ms     1666  i915_mutex_lock_interruptible i915_gem_fault __do_fault handle_pte_fault handle_mm_fault __do_page_fault do_page_fault page_fa
+ult
   4.93 ms     2.45 ms      980  i915_mutex_lock_interruptible intel_crtc_page_flip drm_mode_page_flip_ioctl drm_ioctl i915_compat_ioctl compat_sys_ioctl ia32_
+sysret
   4.89 ms     2.20 ms     3283  i915_mutex_lock_interruptible i915_gem_wait_ioctl drm_ioctl i915_compat_ioctl compat_sys_ioctl ia32_sysret
   4.34 ms     1.66 ms     1715  i915_mutex_lock_interruptible i915_gem_pwrite_ioctl drm_ioctl i915_compat_ioctl compat_sys_ioctl ia32_sysret
   3.73 ms     3.73 ms       49  i915_mutex_lock_interruptible i915_gem_set_domain_ioctl drm_ioctl i915_compat_ioctl compat_sys_ioctl ia32_sysret
   3.17 ms     0.33 ms      931  i915_mutex_lock_interruptible i915_gem_madvise_ioctl drm_ioctl i915_compat_ioctl compat_sys_ioctl ia32_sysret
   2.97 ms     0.43 ms     1029  i915_mutex_lock_interruptible i915_gem_busy_ioctl drm_ioctl i915_compat_ioctl compat_sys_ioctl ia32_sysret
   2.55 ms     0.51 ms      735  i915_gem_get_tiling drm_ioctl i915_compat_ioctl compat_sys_ioctl ia32_sysret

After the patch it looks like this:

   4.99 ms     2.14 ms    22212  __wait_seqno i915_gem_wait_ioctl drm_ioctl i915_compat_ioctl compat_sys_ioctl ia32_sysret
   4.86 ms     0.99 ms    14170  __wait_seqno i915_gem_object_wait_rendering__nonblocking i915_gem_fault __do_fault handle_pte_fault handle_mm_fault __do_page_
+fault do_page_fault page_fault
   3.59 ms     1.31 ms      325  i915_gem_get_tiling drm_ioctl i915_compat_ioctl compat_sys_ioctl ia32_sysret
   3.37 ms     3.37 ms       65  i915_mutex_lock_interruptible i915_gem_wait_ioctl drm_ioctl i915_compat_ioctl compat_sys_ioctl ia32_sysret
   2.58 ms     2.58 ms       65  i915_mutex_lock_interruptible i915_gem_do_execbuffer.isra.23 i915_gem_execbuffer2 drm_ioctl i915_compat_ioctl compat_sys_ioctl
+ia32_sysret
   2.19 ms     2.19 ms       65  i915_mutex_lock_interruptible intel_crtc_page_flip drm_mode_page_flip_ioctl drm_ioctl i915_compat_ioctl compat_sys_ioctl ia32_
+sysret
   2.18 ms     2.18 ms       65  i915_mutex_lock_interruptible i915_gem_busy_ioctl drm_ioctl i915_compat_ioctl compat_sys_ioctl ia32_sysret
   1.66 ms     1.66 ms       65  i915_gem_set_tiling drm_ioctl i915_compat_ioctl compat_sys_ioctl ia32_sysret

It may not look like it, but this is quite a large difference, and I've
been unable to reproduce > 5 msec delays at all, while before they do
happen (just not in the trace above)."

gem_gtt_hog on an old Pineview (GMA3150),
before: 4969.119ms
after:  4122.749ms
Reported-by: NArjan van de Ven <arjan.van.de.ven@intel.com>
Testcase: igt/gem_gtt_hog
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When we detect that the user passed along an invalid handle or object,
we emit a warning as an aide for debugging. Since these are indeed only
for debugging user triggerable errors (and the errors are reported back
to userspace by the errno), the messages should only be at the debug
level and not claiming that there is a catastrophic error in the
driver/hardware.

References: https://bugs.freedesktop.org/show_bug.cgi?id=74704Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If we make sure that all the dev_priv->info usages are wrapped by
INTEL_INFO(), we can easily modify the ->info field to be structure and
not a pointer while keeping the const protection in the INTEL_INFO()
macro.

v2: Rebased onto latest drm-nightly
Suggested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since a purged buffer is one without any associated pages, attempting to
use it should generate EFAULT rather than EINVAL, as it is not strictly
an invalid parameter.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

EFAULT will be a possible return code where backing storage is
transient, such after it is purged by madvise. As such it is to be
expected and so should not trigger a WARN inside i915_gem_fault() but be
converted silently to SIGBUS.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Found with smatch.
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

As we seek the guilty batch using request and hangcheck
score, this code is not needed anymore.

v2: Rebase. Passing dev_priv instead of getting it from last_ring
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With full ppgtt using acthd is not enough to find guilty
batch buffer. We get multiple false positives as acthd is
per vm.

Instead of scanning which vm was running on a ring,
to find corressponding context, use a different, simpler,
strategy of finding batches that caused gpu hang:

If hangcheck has declared ring to be hung, find first non complete
request on that ring and claim it was guilty.

v2: Rebase

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73652Suggested-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If we have stopped rings then we know that test is running
so no need for spam. In addition, only spam when default
context gets banned.

v2: - make sure default context ban gets shown (Chris)
    - use helper for checking for default context, everywhere (Chris)

v3: - dont be quiet when debug is set (Ben, Daniel)

Reference: https://bugs.freedesktop.org/show_bug.cgi?id=73652Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With full ppgtt support drm_i915_file_private gained knowledge
about the default context. Also reset stats are now inside
i915_hw_context so we can use proper abstraction.

v2: Move BUG_ON and WARN_ON to more proper locations (Ben)

v3: Pass dev directly to i915_context_is_banned to avoid the need to
dereference ctx->last_ring. Spotted by Mika when checking my
s/BUG/WARN/ change, I've missed this ->last_ring dereference.
Suggested-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> (v2)
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (v2)
[danvet: s/BUG/WARN/]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

At least I couldn't find it in the Haswell Bspec any more and we've
tried to test-boot a Haswell machine with num_pipes forced to 0 (i.e.
hit the PCH_NOP path) and the unclaimed register logic complained.

So restrict this dance to just ivb platforms.

v2: Art pointed out that the bits simply moved on hsw+

v3: Buy code terseneness with a notch of sublety as suggested by
Chris.

v4: Frob the right bit, spotted by Art.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Arthur Ranyan <arthur.j.runyan@intel.com>
Cc: Dave Airlie <airlied@gmail.com>
Reviewed-by: NArt Runyan <arthur.j.runyan@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With 20+ module parameters, I think referring to them via a struct
improves clarity over just having a bunch of globals. While at it, move
the parameter initialization and definitions into a new file
i915_params.c to reduce clutter in i915_drv.c.

Apart from the ill-named i915_enable_rc6, i915_enable_fbc and
i915_enable_ppgtt parameters, for which we lose the "i915_" prefix
internally, the module parameters now look the same both on the kernel
command line and in code. For example, "i915.modeset".

The downsides of the change are losing static on a couple of variables
and not having the initialization and module_param_named() right next to
each other. On the other hand, all module parameters are now defined in
one place at i915_params.c. Plus you can do this to find all module
parameter references:

$ git grep "i915\." -- drivers/gpu/drm/i915

v2:
- move the definitions into a new file
- s/i915_params/i915/
- make i915_try_reset i915.reset, for consistency
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is useful for debugging as we then know that the first entry is
always the global GTT, and all later entries the per-process GTT VM.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>