Defer connector registration from during construction to the driver
registration phase. This is important for ordering the action correctly,
e.g. not using debugfs before it is ready.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-4-git-send-email-chris@chris-wilson.co.uk

Currently the backlight is being registered in the load phase (before
the display and its objects are registered). Move the backlight
registration into the analogous phase by performing it from the
connector registration, just after its creation.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-3-git-send-email-chris@chris-wilson.co.uk

With the introduction of a connector->func for callback from
drm_connector_register() we can move all the tasks that we want to do
upon registration into that callback. Later, this will allow us to
reorder the registration and defer it until after the device is setup
and ready for userspace.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-2-git-send-email-chris@chris-wilson.co.uk

Currently setting up the backlight for a panel is sometimes done
together with initialising the panel, and sometimes after the connector
is registered. The backlight setup does not depend upon connector
registration (i.e. access to sysfs/debugfs and the kobject hierachy) so
perform it consistently just after panel initialisation.

Note the discrepancy here as destroying the panel is done during
connector unregistration...
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-1-git-send-email-chris@chris-wilson.co.uk

Effectively removes one layer of indirection between the mask of
possible engines and the engine constructors. Instead of spelling
out in code the mapping of HAS_<engine> to constructors, makes
more use of the recently added data driven approach by putting
engine constructor vfuncs into the table as well.

Effect is fewer lines of source and smaller binary.

At the same time simplify the error handling since engine
destructors can run on unitialized engines anyway.

Similar approach could be done for legacy submission is wanted.

v2: Removed ugly BUILD_BUG_ONs in favour of newly introduced
    ENGINE_MASK and HAS_ENGINE macros.
    Also removed the forward declarations by shuffling functions
    around.

v3: Warn when logical_rings table does not contain enough data
    and disable the engines which could not be initialized.
    (Chris Wilson)

v4: Chris Wilson suggested a nicer engine init loop.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1466689961-23232-1-git-send-email-tvrtko.ursulin@linux.intel.com

Backmerge drm-next for the reworked device register/unregistering.
Chris Wilson needs that to be able to land his i915 load/unload
demidlayering.
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

MT8173 HDMI support

- device tree binding documentation for MT8173 HDMI encoder, CEC, DDC,
  and PHY
- drivers for MT8173 HDMI encoder, CEC (HPD only for now), DDC, and PHY
- enable HDMI output via a custom SMCCC call
- add ddc-i2c-bus property to HDMI connector device tree binding

* tag 'mediatek-drm-2016-06-20' of git://git.pengutronix.de/git/pza/linux:
  dt-bindings: hdmi-connector: add DDC I2C bus phandle documentation
  drm/mediatek: enable hdmi output control bit
  drm/mediatek: Add HDMI support
  dt-bindings: drm/mediatek: Add Mediatek HDMI dts binding

some rcar-du fixes.

* 'drm/next/du' of git://linuxtv.org/pinchartl/media:
  drm: rcar-du: error message is not needed for EPROBE_DEFER
  drm: rcar-du: error message is not needed for drm_vblank_init()
  rcar-du: add/rename DEFR6 TCON bits

- Infrastructure for GVT-g (paravirtualized gpu on gen8+), from Zhi Wang
- another attemp at nonblocking atomic plane updates
- bugfixes and refactoring for GuC doorbell code (Dave Gordon)
- GuC command submission enabled by default, if fw available (Dave Gordon)
- more bxt w/a (Arun Siluvery)
- bxt phy improvements (Imre Deak)
- prep work for stolen objects support (Ankitprasa Sharma & Chris Wilson)
- skl/bkl w/a update from Mika Kuoppala
- bunch of small improvements and fixes all over, as usual

* tag 'drm-intel-next-2016-06-20' of git://anongit.freedesktop.org/drm-intel: (81 commits)
  drm/i915: Update DRIVER_DATE to 20160620
  drm/i915: Introduce GVT context creation API
  drm/i915: Support LRC context single submission
  drm/i915: Introduce execlist context status change notification
  drm/i915: Make addressing mode bits in context descriptor configurable
  drm/i915: Make ring buffer size of a LRC context configurable
  drm/i915: gvt: Introduce the basic architecture of GVT-g
  drm/i915: Fold vGPU active check into inner functions
  drm/i915: Use offsetof() to calculate the offset of members in PVINFO page
  drm/i915: Factor out i915_pvinfo.h
  drm/i915: Serialise presentation with imported dmabufs
  drm/i915: Use atomic commits for legacy page_flips
  drm/i915: Move fb_bits updating later in atomic_commit
  drm/i915: nonblocking commit
  Reapply "drm/i915: Pass atomic states to fbc update, functions."
  drm/i915: Roll out the helper nonblock tracking
  drm/i915: Signal drm events for atomic
  drm/i915/ilk: Don't disable SSC source if it's in use
  drm/i915/guc: (re)initialise doorbell h/w when enabling GuC submission
  drm/i915/guc: replace assign_doorbell() with select_doorbell_register()
  ...

Merge tag 'topic/drm-misc-2016-06-22-updated' of git://anongit.freedesktop.org/drm-intel into drm-next

Again a pile of things all over
- Conversion to rst from docbook from Jani. Looks real pretty, and the
  source is now actually readable (compared to horrible, horrible docbook
  xml)! https://01.org/linuxgraphics/gfx-docs/drm/
- device register/unregister rework from Chris, with follow-up work from
  Benjamin. Allows more drivers to demidlayer load/unload and others to
  remove a bit of boilerplate.
- master/auth related cleanup, with docs
- some dma-buf polish, merged by Sumit
- small stuff all over (like build fixes from Arnd)

Group maintainership seems to slowly take off, with both Thierry and Sumit
pushing a few things. No hiccups thus far.

* tag 'topic/drm-misc-2016-06-22-updated' of git://anongit.freedesktop.org/drm-intel: (68 commits)
  drm/vc4: Remove unused connector
  drm/fb-helper: Reduce READ_ONCE(master) to lockless_dereference
  drm/sun4i: Remove open-coded drm_connector_register_all()
  drm/vc4: Remove open-coded drm_connector_register_all()
  drm/atmel-hlcdc: Remove redundant call to drm_connector_unregister_all()
  drm: document drm_auth.c
  drm: Clear up master tracking booleans
  drm: Extract drm_is_current_master
  drm: Refactor drop/set master code a bit
  drm: Lobotomize set_busid nonsense for !pci drivers
  drm: Nuke SET_UNIQUE ioctl
  drm: Don't call drm_dev_set_unique from platform drivers
  drm/vgem: Stop calling drm_drv_set_unique
  drm: Use dev->name as fallback for dev->unique
  drm: Clean up drm_crtc.h
  drm: Move master pointer from drm_minor to drm_device
  drm: sti: rework init sequence
  drm: sti: use late_register and early_unregister callbacks
  drm/amdkfd: Clean up inline handling
  drm: Add callbacks for late registering
  ...

Add basic support for the sii902x RGB -> HDMI bridge.

* tag 'drm-sii902x' of github.com:bbrezillon/linux-at91:
  drm/bridge: Add sii902x DT bindings doc
  drm/bridge: Add sii902x driver

During hibernation the cached DP port register value will be left with
whatever value we have there when we create the hibernation image.
Currently that means the port (and eDP PLL) will be off in the cached
value. However when we resume there is no guarantee that the value
in the actual register will match the cached value. If i915 isn't
loaded in the kernel that loads the hibernation image, the port may
well be on (eg. left on by the BIOS). The encoder state readout
does the right thing in this case and updates our encoder state
to reflect the actual hardware state. However the post-resume modeset
will then use the stale cached port register value in
intel_dp_link_down() and potentially confuse the hardware.

This was caught by the following assert
 WARNING: CPU: 3 PID: 5288 at ../drivers/gpu/drm/i915/intel_dp.c:2184 assert_edp_pll+0x99/0xa0 [i915]
 eDP PLL state assertion failure (expected on, current off)
on account of the eDP PLL getting prematurely turned off when
shutting down the port, since the DP_PLL_ENABLE bit wasn't set
in the cached register value.

Presumably I introduced this problem in
commit 6fec7662 ("drm/i915: Use intel_dp->DP in eDP PLL setup")
as before that we didn't update the cached value after shuttting the
port down. That's assuming the port got enabled at least once prior
to hibernating. If that didn't happen then the cached value would
still have been totally out of sync with reality (eg. first boot w/o
eDP on, then hibernate, and then resume with eDP on).

So, let's fix this properly and refresh the cached register value from
the hardware register during resume.

DDI platforms shouldn't use the cached value during port disable at
least, so shouldn't have this particular issue. They might still have
issues if we skip the initial modeset and then try to retrain the link
or something. But untangling this DP vs. DDI mess is a bigger topic,
so let's jut punt on DDI for now.

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Fixes: 6fec7662 ("drm/i915: Use intel_dp->DP in eDP PLL setup")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463162036-27931-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

The wait for panel status helper will only function correctly if the
HW panel timings are programmed correctly. Returning prematurely from
this helper may lead to obscure bugs later, so sanity check the HW
timing registers.

v2:
- Check the T8, T9 fields too, we do program them (Ville)

CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466096506-11937-1-git-send-email-imre.deak@intel.com

This will be needed by the next patch too so factor it out.

No functional change.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466084243-5388-4-git-send-email-imre.deak@intel.com

No functional change.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466084243-5388-3-git-send-email-imre.deak@intel.com

The PPS registers are backed by power well #0 and as such may be reset
after system or runtime suspend (both implying a possible DC9
transition). Fix this by reusing the VLV/CHV PPS pipe-reassignment
logic. The difference on BXT is that the PPS instances are not pipe but
port (or more accurately pin) specific, so we only need to care about
the lost HW state. As opposed to VLV/CHV the SW state is fixed and
initialized during connector init.

This also paves the way towards using the actual port->PPS instance
mapping based on VBT.

This fixes eDP link training errors on BXT after suspend, where we
started the link training too early due to an incorrect T3 (panel power
on) register value.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96436Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466084243-5388-2-git-send-email-imre.deak@intel.com

Move the early PPS initialization calls next to the rest of PPS
initialization steps. This allows us to forgo a duplicated call to
intel_dp_init_panel_power_sequencer_registers() on VLV/CHV.

This will swap the order of DP AUX registration wrt. PPS initialization.
There is an existing race here in case of a user space access via the
DPAUX device node after DP AUX registration and before calling
intel_dp_init_panel_power_sequencer_registers(), but this change won't
make this worse. The fix for this is to separate DP AUX initialization
and registration, that's a separate work already underway.

The order of MST wrt. PPS init as well as the order of
intel_dp_init_panel_power_sequencer_registers() wrt.
intel_edp_panel_vdd_sanitize() also swap, which is ok, there are no
dependencies between these steps.

Suggested by Ville.

CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466499109-20240-4-git-send-email-imre.deak@intel.com

The initial DPCD read for eDP detection involves using the PPS, but so
far we only initialized the PPS registers after the DPCD read. The
reason this was done so far is to preserve a possible LVDS PPS HW setup
if LVDS is detected but eDP is not. This is not an issue any more after
the previous patch, so we can move the init earlier now.

This was caught by CI with the PPS sanity checks in place and the
initial eDP DPCD readout waiting for the panel power cycle timeout
without the PPS registers being initialized.

CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466499109-20240-3-git-send-email-imre.deak@intel.com

Atm on IBX/CPT we attempt to detect if eDP is present even if LVDS was
already detected and an encoder for it was registered. This involves
trying to read out the eDP DPCD, which in turn needs the same power
sequencer that LVDS uses. Poking at the VDD line at an unexpected time
may or may not interfere with the LVDS panel, but it's probably safer to
prevent this. Registering both an LVDS and an eDP connector would also
present a similar problem accessing the shared PPS at any point later in
an unexpected way.

We also need this to be able fix PPS initialization before its first use
in the next patch. For that we want to be sure that PPS is not in use
by LVDS.

v2:
- Split out the PPS init fix to a separate patch. (Chris)
- Add comment about eDP init depending on LVDS init. (Chris)
- Make the use of the intel_encoder ptr less error prone.
v3:
- Use IBX/CPT reference instead of the incorrect ILK, add a WARN about
  this. (Ville)
v4:
- Use a helper to get the lvds encoder instead of opencoding the same.
  (Ville)

CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v2)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v3)
Link: http://patchwork.freedesktop.org/patch/msgid/1466499109-20240-2-git-send-email-imre.deak@intel.com

Somehow I didn't spot this when pushing :(

Fixes: 398e9799 ("drm/vc4: Remove open-coded drm_connector_register_all()")
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

We are only documenting that the read is outside of the lock, and do not
require strict ordering on the operation. In this case the more relaxed
lockless_dereference() will suffice.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466581572-16608-1-git-send-email-chris@chris-wilson.co.uk

drm_dev_register() will now register all known connectors, so we no
longer have to do so manually.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466501283-19976-4-git-send-email-chris@chris-wilson.co.uk

drm_dev_register() will now register all known connectors, so we no
longer have to do so manually.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Eric Anholt <eric@anholt.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466501283-19976-3-git-send-email-chris@chris-wilson.co.uk

drm_connector_unregister_all() is not automatically called by
drm_dev_unregister() so we can drop the local call.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466501283-19976-2-git-send-email-chris@chris-wilson.co.uk

Also extract drm_auth.h for nicer grouping.

v2: Nuke the other comments since they don't really explain a lot, and
within the drm core we generally only document functions exported to
drivers: The main audience for these docs are driver writers.

v3: Limit the exposure of drm_master internals by only including
drm_auth.h where it is neede (Chris).

v4: Spelling polish (Emil).

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NEmil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

- is_master can be removed, we can compute this by checking allowed_master
  (which really just tracks whether a master struct has been allocated
  for this fpriv in either open or set_master), and whether the fpriv is
  the current master on the device.

- that frees up is_master as a good replacement name for allowed_master.
  With that it's clear that it tracks whether the fpriv is a master (with
  possibly clients attached to it and authenticated against it), and that
  one of those fprivs with is_master set is the current master.

v2: Fix kerneldoc for is_master (Emil).

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NEmil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466499262-18717-10-git-send-email-daniel.vetter@ffwll.ch

Just rolling out a bit of abstraction to be able to clean
up the master logic in the next step.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NEmil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

File open/set_maseter ioctl and file close/drop_master ioctl share the
same master handling code. Extract it.

Note that vmwgfx's master_set callback needs to know whether the
master is a new one or has been used already, so thread this through.
On the close/drop side a similar parameter existed, but wasnt used.
Drop it to simplify the flow.

v2: Try to make it not leak so much (Emil).

v3: Send out the right version ...

Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NEmil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466511638-9885-1-git-send-email-daniel.vetter@ffwll.ch

We already have a fallback in place to fill out the unique from
dev->unique, which is set to something reasonable in drm_dev_alloc.

Which means we only need to have a special set_busid for pci devices,
to be able to care the backwards compat code for drm 1.1 around, which
libdrm still needs.

While developing and testing this patch things blew up in really
interesting ways, and the code is rather confusing in naming things
between the kernel code, ioctl #defines and libdrm. For the next brave
dragon slayer, document all this madness properly in the userspace
interface section of gpu.tmpl.

v2: Make drm_dev_set_unique static and update kerneldoc.

v3: Entire rewrite, plus document what's going on for posterity in the
gpu docbook uapi section.

v4: Drop accidental amdgpu hunk (Emil).

v5: Drop accidental omapdrm vblank counter change (Emil).

v6: Rebase on top of the sphinx conversion.

Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> (virt_gpu)
Reviewed-by: NEmil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

Ever since

commit 2e1868b560315a8b20d688e646c489a5ad93eeae
Author: Eric Anholt <anholt@freebsd.org>
Date:   Wed Jun 16 09:25:21 2004 +0000

    DRI trunk-20040613 import

the X server supports drm 1.1, thus doesn't call call libdrm's
drmSetBusid - the sole user of this ioctl. When reviewing this note
that for hilarity both the kernel-internal functions (set_busid) and
the libdrm wrapper (drmSetBusid) have names not matching this ioctl
(SET_UNIQUE).

v2: Polish commit message (Emil).

Cc: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: NEmil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466499262-18717-6-git-send-email-daniel.vetter@ffwll.ch

Since

commit e112e593
Author: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Date:   Fri Dec 11 11:20:28 2015 +0100

    drm: use dev_name as default unique name in drm_dev_alloc()

we're using a reasonable default which should work for everyone. Only
mtk, rcar-du and sun4i are affected, and as kms-only drivers without
any rendering support no one should ever care about the unique name

v2: Rebase on top of mediatek.

Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: NEmil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466499262-18717-5-git-send-email-daniel.vetter@ffwll.ch

With the previous patch this is now redudant, the core always
sets a reasonable dev->unique string.

Cc: Sean Paul <seanpaul@chromium.org>
Reviewed-by: NEmil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466499262-18717-4-git-send-email-daniel.vetter@ffwll.ch

Lots of arm drivers get this wrong and for most arm boards this is the
right thing actually. And anyway with most loaders you want to chase
sysfs links anyway to figure out which dri device you want.

This will fix dmesg noise for rockchip and sti.

Also add a fallback to driver->name for entirely virtual drivers like
vgem.

v2: Rebase on top of

commit e112e593
Author: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Date:   Fri Dec 11 11:20:28 2015 +0100

    drm: use dev_name as default unique name in drm_dev_alloc()

and simplify a bit. Plus add a comment.

v3: WARN_ON(!dev->unique) as discussed with Emil.

Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Reported-by: NIlia Mirkin <imirkin@alum.mit.edu>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v2)
Reviewed-by: NEmil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466499262-18717-3-git-send-email-daniel.vetter@ffwll.ch

- Group declarations for separate files (drm_bridge.c, drm_edid.c)
- Move declarations only used within drm.ko to drm_crtc_internal.h
- drm_property_type_valid to drm_crtc.c, its only callsite
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NEmil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466499262-18717-2-git-send-email-daniel.vetter@ffwll.ch

There can only be one current master, and it's for the overall device.
Render/control minors don't support master-based auth at all.

This simplifies the master logic a lot, at least in my eyes: All these
additional pointer chases are just confusing.

While doing the conversion I spotted some locking fail:
- drm_lock/drm_auth check dev->master without holding the
  master_mutex. This is fallout from

  commit c996fd0b
  Author: Thomas Hellstrom <thellstrom@vmware.com>
  Date:   Tue Feb 25 19:57:44 2014 +0100

      drm: Protect the master management with a drm_device::master_mutex v3

  but I honestly don't care one bit about those old legacy drivers
  using this.

- debugfs name info should just grab master_mutex.

- And the fbdev helper looked at it to figure out whether someone is
  using KMS. We just need a consistent value, so READ_ONCE. Aside: We
  should probably check if anyone has opened a control node too, but I
  guess current userspace doesn't really do that yet.

v2: Balance locking, reported by Julia.

v3: Rebase on top of Chris' oops fixes.

Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v2)
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com> (v2)
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466499262-18717-1-git-send-email-daniel.vetter@ffwll.ch

Use drm_dev_alloc() and drm_dev_register() instead of .load()
To simplify init sequence only create fbdev when requested
in output_poll_changed().

version 2:
remove call to drm_connector_unregister_all() and
drm_dev_set_unique()
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466514580-15194-4-git-send-email-benjamin.gaignard@linaro.org

Make sti driver use register callback to move debugfs
initialization out of sub-components creation.
This will allow to convert driver .load() to
drm_dev_alloc() and drm_dev_register().

sti_compositor bring up 2 crtc but only one debugfs init is
needed so use drm_crtc_index to do it on the first one.
This can't be done in sti_drv because only sti_compositor have
access to the devices.
It is almost the same for sti_encoder which handle multiple
encoder while one only debugfs entry is needed so add a boolean
to avoid multiple debugfs initialization
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466514580-15194-3-git-send-email-benjamin.gaignard@linaro.org

- inline functions need to be static inline, otherwise gcc can opt to
  not inline and the linker gets unhappy.
- no forward decls for inline functions, just include the right headers.

Cc: Oded Gabbay <oded.gabbay@gmail.com>
Cc: Ben Goz <ben.goz@amd.com>
Reviewed-by: NOded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466500235-21282-2-git-send-email-daniel.vetter@ffwll.ch

Like what has been done for connectors add callbacks on encoder,
crtc and plane to let driver do actions after drm device registration.

Correspondingly, add callbacks called before unregister drm device.

version 2:
add drm_modeset_register_all() and drm_modeset_unregister_all()
to centralize all calls

version 3:
in error case unwind registers in drm_modeset_register_all
fix uninitialed return value
inverse order of unregistration in drm_modeset_unregister_all

version 4:
move function definitions in drm_crtc_internal.h
remove not needed documentation
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466519829-4000-1-git-send-email-benjamin.gaignard@linaro.org

No need for local struct drm_device * since dev_priv is the
correct thing to pass in to NEEDS_WaRsDisableCoarsePowerGating
anyway. Changed the macro definition for the latter to reflect
that as well.

v2: Alignment bikeshed.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466518034-24838-1-git-send-email-tvrtko.ursulin@linux.intel.com