Define tuner types V4L2_TUNER_ADC and V4L2_TUNER_RF for SDR usage.

ADC is used for setting sampling rate (sampling frequency) to SDR
device.

Another tuner type, named as V4L2_TUNER_RF, is possible RF tuner.
Is is used to down-convert RF frequency to range ADC could sample.
Having RF tuner is optional, whilst in practice it is almost always
there.

Also add checks to VIDIOC_G_FREQUENCY, VIDIOC_S_FREQUENCY and
VIDIOC_ENUM_FREQ_BANDS only allow these two tuner types when device
type is SDR (VFL_TYPE_SDR). For VIDIOC_G_FREQUENCY we do not check
tuner type, instead override type with V4L2_TUNER_ADC in every
case (requested by Hans in order to keep functionality in line with
existing tuners and existing API does not specify it).

Prohibit VIDIOC_S_HW_FREQ_SEEK explicitly when device type is SDR,
as device cannot do hardware seek without a hardware demodulator.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add new V4L device type VFL_TYPE_SDR for Software Defined Radio.
It is registered as /dev/swradio0 (/dev/sdr0 was already reserved).
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add new video4linux device named /dev/swradio for Software Defined
Radio use. V4L device minor numbers are allocated dynamically
nowadays, but there is still configuration option for old fixed style.
Add note to mention that configuration option too.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NAlan Cox <alan@linux.intel.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This device has a led at bit 7 of GPIO reg. 0x80 to indicate
when a DVB capture is happening.

Add support for it.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Some devices have a LED to indicate when DVB capture started.
Add support for it.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This device is close to Kworld UB435-Q, but it uses a different
tuner. Add support for it.

Tested with both 8VSB and 256QAM modulations.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

tda18272 is programmed just like tda18212, but it also
supports ClearQAM and ATSC.

Add support for them. Tested with a Kworld UB435-Q on both
8VSB and 256QAM modes.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Some boards got added there. Update the cardlist to reflect the
current status.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Some new boards got added. Update the cardlist.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Currently, there's just one device using this frontend: PCTV 80e,
and it works on serial mode.

Change the default here to serial mode. If we add more devices,
then this option should be set via config structure.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The cfg_mpeg_output has more fields than what it is initialized
when the code is called. Be sure to initialize everything before
use, in order to avoid random behaviors.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Just like the windows driver, disable OOB after setting the driver
version.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

DJH_DEBUG only code path in drxbsp_i2c_write_read() dereferences
w_dev_addr and subsequently w_dev_addr->user_data->i2c which results
in failure during boot. This patch fixes the null pointer derefence
bug as well as the following compile errors:

  LD      arch/x86/built-in.o
  CC      drivers/media/dvb-frontends/drx39xyj/drxj.o
drivers/media/dvb-frontends/drx39xyj/drxj.c: In function ‘drxbsp_i2c_write_read’:
drivers/media/dvb-frontends/drx39xyj/drxj.c:1558:25: error: redeclaration of ‘state’ with no linkage
  struct drx39xxj_state *state = w_dev_addr->user_data;
                         ^
drivers/media/dvb-frontends/drx39xyj/drxj.c:1512:25: note: previous declaration of ‘state’ was here
  struct drx39xxj_state *state;
                         ^
drivers/media/dvb-frontends/drx39xyj/drxj.c:1558:2: warning: ISO C90 forbids mixed declarations and code [-Wdeclaration-after-statement]
  struct drx39xxj_state *state = w_dev_addr->user_data;
  ^
drivers/media/dvb-frontends/drx39xyj/drxj.c:1560:17: error: redeclaration of ‘msg’ with no linkage
  struct i2c_msg msg[2] = {
                 ^
drivers/media/dvb-frontends/drx39xyj/drxj.c:1513:17: note: previous declaration of ‘msg’ was here
  struct i2c_msg msg[2];
                 ^
Signed-off-by: NShuah Khan <shuah.kh@samsung.com>
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

drxbsp_i2c_write_read() has return that prevents DJH_DEBUG code to run.
Remove it.
Signed-off-by: NShuah Khan <shuah.kh@samsung.com>
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

drxj.c fails to compile with the following errors when DJH_DEBUG
is defined.

drivers/media/dvb-frontends/drx39xyj/drxj.c:1567:2: error: implicit declaration of function ‘pr_dbg’ [-Werror=implicit-function-declaration]
  pr_dbg("drx3933 i2c operation addr=%x i2c=%p, wc=%x rc=%x\n",
  ^
Signed-off-by: NShuah Khan <shuah.kh@samsung.com>
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Mimic what windows driver does here: it writes 0x07 to
SIO_CC_SOFT_RST__A, instead of just 0x03.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

As drxj_close puts the device in powerdown, we need to power it up
properly at drxj_open.

This is the behavior noticed at the Windows driver.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

There are no other I2C masters here. Also, the Windows driver uses
this mode (and both drxd and drxk Kernel drivers). So, switch
to it.

That helps to compare the logs between the Linux driver and the
Windows one.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Instead of just disabling the LNA every time, allow to control it from
userspace.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

On several places, the I2C functions are just wrappers to others.

Get rid of it.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This struct contains the first abstraction layer for the I2C
access routines. Get rid of it.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This file contains an abstract layer for the I2C transfer
functions. Get rid of it, merging it at drxj. This will allow
to remove another abstraction layer there, making the code
easier to read, and removing the functions that just return
-EIO.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Reorder functions and data at drx_dap_fasi.c, in order to avoid
having function prototypes.

This is in preparation to merge this code inside drxj, removing
some duplicated bits there, and getting rid of yet another
abstraction layer.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This is not used anywere. Get rid of it.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

QAM/256 currently doesn't work, as the code is only called if
channel->mirror is DRX_MIRROR_AUTO, but a prevous if prevents
this condition to happen.

While here, returns -EINVAL to not supported QAM modes and
simplify the code, reducing the number of indents.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Those struct data aren't used anymore. Get rid of them.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Checking if a time is after another one can have issues, as
times are generally u32 wide.

Use the proper macros for that at scu_command().

It should be noticed that other places also use jiffies
calculus on an improper way. This should be fixed too,
but the logic there is more complex. So, let's do it in
separate patches.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Modulation and other parameters might have changed. So, better
to call ctrl_set_standard() even if the device is already
powered.

That helps to put the device into a sane state, if something
got wrong on a previous set_frontend call.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

When switching from one video standard to another one,
power_down_vsb is called twice. Well, as the device is already
in power_down mode, the second call always fail. This causes that
any subsequent frontend set to fail as well:

[145074.501243] drx39xyj:power_down_vsb: called
[145089.195396] drx39xyj:power_down_vsb: error -5
[145089.195404] drx39xyj:ctrl_set_standard: error -5
[145089.195417] drx39xyj:drx39xxj_set_frontend: Failed to set standard! result=fffffffb
[145089.195470] drx39xyj:ctrl_sig_quality: error -5
[145089.195473] drx39xyj:drx39xxj_read_ber: drx39xxj: could not get ber!
[145089.195475] drx39xyj:ctrl_sig_quality: error -5
[145089.195477] drx39xyj:drx39xxj_read_signal_strength: drx39xxj: could not get signal strength!
[145089.195479] drx39xyj:ctrl_sig_quality: error -5
[145089.195480] drx39xyj:drx39xxj_read_snr: drx39xxj: could not read snr!
[145089.195482] drx39xyj:ctrl_sig_quality: error -5
[145089.195484] drx39xyj:drx39xxj_read_ucblocks: drx39xxj: could not get uc blocks!
[145089.195498] drx39xyj:ctrl_sig_quality: error -5
[145089.195500] drx39xyj:drx39xxj_read_ber: drx39xxj: could not get ber!
[145089.195502] drx39xyj:ctrl_sig_quality: error -5
[145089.195503] drx39xyj:drx39xxj_read_signal_strength: drx39xxj: could not get signal strength!
[145089.195505] drx39xyj:ctrl_sig_quality: error -5
[145089.195506] drx39xyj:drx39xxj_read_snr: drx39xxj: could not read snr!
[145089.195508] drx39xyj:ctrl_sig_quality: error -5
[145089.195510] drx39xyj:drx39xxj_read_ucblocks: drx39xxj: could not get uc blocks!
[145090.196291] drx39xyj:drx39xxj_read_status: drx39xxj: could not get lock status!
[145090.196508] drx39xyj:ctrl_sig_quality: error -5
[145090.196511] drx39xyj:drx39xxj_read_ber: drx39xxj: could not get ber!
[145090.196514] drx39xyj:ctrl_sig_quality: error -5
[145090.196515] drx39xyj:drx39xxj_read_signal_strength: drx39xxj: could not get signal strength!
[145090.196518] drx39xyj:ctrl_sig_quality: error -5
[145090.196519] drx39xyj:drx39xxj_read_snr: drx39xxj: could not read snr!
[145090.196522] drx39xyj:ctrl_sig_quality: error -5
[145090.196523] drx39xyj:drx39xxj_read_ucblocks: drx39xxj: could not get uc blocks!
[145090.196553] drx39xyj:ctrl_sig_quality: error -5
[145090.196554] drx39xyj:drx39xxj_read_ber: drx39xxj: could not get ber!
[145090.196557] drx39xyj:ctrl_sig_quality: error -5
[145090.196558] drx39xyj:drx39xxj_read_signal_strength: drx39xxj: could not get signal strength!
[145090.196560] drx39xyj:ctrl_sig_quality: error -5
[145090.196562] drx39xyj:drx39xxj_read_snr: drx39xxj: could not read snr!
[145090.196564] drx39xyj:ctrl_sig_quality: error -5
[145090.196565] drx39xyj:drx39xxj_read_ucblocks: drx39xxj: could not get uc blocks!
[145091.119265] drx39xyj:ctrl_sig_quality: error -5
[145091.119271] drx39xyj:drx39xxj_read_ber: drx39xxj: could not get ber!
[145091.119274] drx39xyj:ctrl_sig_quality: error -5
[145091.119276] drx39xyj:drx39xxj_read_signal_strength: drx39xxj: could not get signal strength!
[145091.119278] drx39xyj:ctrl_sig_quality: error -5
[145091.119280] drx39xyj:drx39xxj_read_snr: drx39xxj: could not read snr!
[145091.119282] drx39xyj:ctrl_sig_quality: error -5
[145091.119283] drx39xyj:drx39xxj_read_ucblocks: drx39xxj: could not get uc blocks!
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Instead of just hardcoding an IF value of 5MHz, use the one
provided by the tuner, with can be different for QAM and
VSB.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Those functions will never be used with Linux DVB binding.

Get rid of them.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This file does an ugly binding between drxj and DVB frontend.

Remove most of the functions there. We still need to get rid of
get_frequency and set_frequency, but such patch is a little more
complex, as it should also remove some previous tuner bindings.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

In order to avoid warnings and to remove dead code, remove
the functions that don't make sense to happen, while commenting
the others that might still be useful some day.

That reduced a lot the text size:

Before:

   text	   data	    bss	    dec	    hex	filename
  58419	   2916	      4	  61339	   ef9b	drivers/media/dvb-frontends/drx39xyj/drx39xyj.ko

After:
   text	   data	    bss	    dec	    hex	filename
  78331	   2916	      4	  81251	  13d63	drivers/media/dvb-frontends/drx39xyj/drx39xyj.ko

Without any functional changes.

It could be make sense latter to remove those drivers or to
move them into an analog-specific part of the driver.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

With this change, we finally got rid of all abstraction
layers on this driver.

This patch also fixes the LNA GPIO settings, as the original
code were using a wrong control name for it.

This patch exposes the several functions that aren't used.
Some of them are related to analog demod that might be
used some day, but others will likely never be needed, as
they don't fit on Linux media APIs.

Latter patches will clean up this mess.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

While drxj is already too big, moving the code there will
make easier to get rid of the drxj_ctrl function.

It will also help to detect and remove the unused functions,
helping to remove lots of dead code there.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Get rid of drx_open and drx_close, as those are just wrapper
functions to drxj_open/drxj_close.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This function is used only as an abstraction layer to call the
two firmware functions. Remove it.

As a bonus, the drx_ctrl_function is now unused and can be
removed.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Remove the duplicated firmware upload code that was commented
inside drxj.c.

This code is not used, and will not work anyway, as it doesn't
download the firmware from userspace.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The version is initialized with zero at drx_driver.c. Keep it,
in order to avoid the risk of causing any regression.

While here, remove the drx_driver.h from drxj, as this is not
required there.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This file contains just the firmware load code, that it is also
somewhat duplicated at drxj.c.

Move the code into there. Latter patches will remove the
duplicated code.
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>