* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup:
  [x86 setup] Work around bug in Xen HVM

Previously, ibmebus derived a device's bus_id from its location code.
The location code is not guaranteed to be unique, so we might get bus_id
collisions if two devices share the same location code.  The OFDT
full_name, however, is unique, so we use that instead (truncating it
on the left if it is too long).
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

On PS3, A storage device may show up in the repository before the hypervisor
has finished probing:
  - If its type is not yet known, it shows up as PS3_DEV_TYPE_STOR_DUMMY,
  - If its regions are being probed, it shows up as having zero regions.
If any of these happen, consider the device not yet present.  The storage
probe thread will retry later.

This fixes the timing-dependent problem where a kernel booted from FLASH ROM
sometimes cannot find the hard disk.
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

At present, running any SPE program on the ps3 will trigger a BUG_ON
when spufs_run_spu tries to clear the master run control bit, as lv1
does not make the master run control available to Linux.

This change makes SPE apps work again by disabling changes to the
master run control on PS3.  Although we don't have the facility to
disable a SPE with supervisor-level privileges, it's better than
hitting the BUG_ON unconditionally.
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Acked-by: NMasato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The Cell BE Architecture spec states that the SPU MFC Class 0 interrupt
is edge-triggered.  The current spu interrupt handler assumes this
behavior and does not clear the interrupt status.

The PS3 hypervisor visualizes all SPU interrupts as level, and on return
from the interrupt handler the hypervisor will deliver a new virtual
interrupt for any unmasked interrupts which for which the status has not
been cleared.  This fix clears the interrupt status in the interrupt
handler.
Signed-off-by: NMasato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Acked-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Apparently XEN does not keep the contents of the 48-bit gdt_48 data
structure that is passed to lgdt in the XEN machine state. Instead it
appears to save the _address_ of the 48-bit descriptor
somewhere. Unfortunately this data happens to reside on the stack and
is probably no longer availiable at the time of the actual protected
mode jump.

This is Xen bug but given that there is a one-line patch to work
around this problem, the linux kernel should probably do this.  My fix
is to make the gdt_48 description in setup_gdt static (in setup_idt
this is already the case). This allows the kernel to boot under
Xen HVM again.
Signed-off-by: NChristian Ehrhardt <lk@c--e.de>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

Initialise s_flags in get_sb_mtd_aux() from the flags parameter.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

I've bisected the deadlock when many small appends are done on jffs2 down to
this commit:

commit 6fe6900e
Author: Nick Piggin <npiggin@suse.de>
Date:   Sun May 6 14:49:04 2007 -0700

    mm: make read_cache_page synchronous

    Ensure pages are uptodate after returning from read_cache_page, which allows
    us to cut out most of the filesystem-internal PageUptodate calls.

    I didn't have a great look down the call chains, but this appears to fixes 7
    possible use-before uptodate in hfs, 2 in hfsplus, 1 in jfs, a few in
    ecryptfs, 1 in jffs2, and a possible cleared data overwritten with readpage in
    block2mtd.  All depending on whether the filler is async and/or can return
    with a !uptodate page.

It introduced a wait to read_cache_page, as well as a
read_cache_page_async function equivalent to the old read_cache_page
without any callers.

Switching jffs2_gc_fetch_page to read_cache_page_async for the old
behavior makes the deadlocks go away, but maybe reintroduces the
use-before-uptodate problem? I don't understand the mm/fs interaction
well enough to say.

[It's fine. dwmw2.]
Signed-off-by: NJason Lunz <lunz@falooley.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Ryusuke Konishi says:

The recent truncate_complete_page() clears the dirty flag from a page
before calling a_ops->invalidatepage(),
^^^^^^
static void
truncate_complete_page(struct address_space *mapping, struct page *page)
{
        ...
        cancel_dirty_page(page, PAGE_CACHE_SIZE);  <--- Inserted here at
kernel 2.6.20

        if (PagePrivate(page))
                do_invalidatepage(page, 0);   ---> will call
a_ops->invalidatepage()
        ...
}

and this is disturbing nfs_wb_page_priority() from calling 
nfs_writepage_locked() that is expected to handle the pending
request (=nfs_page) associated with the page.

int nfs_wb_page_priority(struct inode *inode, struct page *page, int how)
{
        ...
        if (clear_page_dirty_for_io(page)) {
                ret = nfs_writepage_locked(page, &wbc);
                if (ret < 0)
                        goto out;
        }
        ...
}

Since truncate_complete_page() will get rid of the page after
a_ops->invalidatepage() returns, the request (=nfs_page) associated
with the page becomes a garbage in nfs_inode->nfs_page_tree.
------------------------

Fix this by ensuring that nfs_wb_page_priority() recognises that it may
also need to clear out non-dirty pages that have an nfs_page associated
with them.
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

According to the mount(2) man page, the proper error return code for the
mount(2) system call when the special device name or the mounted-on
directory name is too long is ENAMETOOLONG.
Signed-off-by: NChuck Lever <chuck.lever@oracle.com>
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

The hostname was getting truncated in the new text-based NFS mount API.
Signed-off-by: NChuck Lever <chuck.lever@oracle.com>
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

Don't filter the return code from the in-kernel rpcbind or NFS mount
clients.  Return the real error code so that callers of the new NFS
text-based mount API can apply a useful retry strategy.
Signed-off-by: NChuck Lever <chuck.lever@oracle.com>
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

The new text-based NFS mount option parsing logic doesn't recognize any
valid transport protocols due to a silly mistake in the protocol token
matching logic.  This prevents basic mount requests such as:

   mount.nfs server:/export /mnt -o proto=tcp

from working with the new text-based NFS mount API.
Signed-off-by: NChuck Lever <chuck.lever@oracle.com>
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

This patch fixes an Oops that was reported by Gabriel Barazer.
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

This should fix the following Oops reported by Jeff Garzik:

kernel BUG at fs/nfs/nfs4xdr.c:1040!
invalid opcode: 0000 [1] SMP 
CPU 0 
Modules linked in: nfs lockd sunrpc af_packet
ipv6 cpufreq_ondemand acpi_cpufreq battery floppy nvram sg snd_hda_intel
ata_generic snd_pcm_oss snd_mixer_oss snd_pcm i2c_i801 snd_page_alloc e1000
firewire_ohci ata_piix i2c_core sr_mod cdrom sata_sil ahci libata sd_mod
scsi_mod ext3 jbd ehci_hcd uhci_hcd
Pid: 16353, comm: 10.10.10.1-recl Not tainted 2.6.23-rc3 #1
RIP: 0010:[<ffffffff88240980>] [<ffffffff88240980>] :nfs:encode_open+0x1c0/0x330
RSP: 0018:ffff8100467c5c60  EFLAGS: 00010202
RAX: ffff81000f89b8b8 RBX: 00000000697a6f6d RCX: ffff81000f89b8b8
RDX: 0000000000000004 RSI: 0000000000000004 RDI: ffff8100467c5c80
RBP: ffff8100467c5c80 R08: ffff81000f89bc30 R09: ffff81000f89b83f
R10: 0000000000000001 R11: ffffffff881e79e0 R12: ffff81003cbd1808
R13: ffff81000f89b860 R14: ffff81005fc984e0 R15: ffffffff88240af0
FS:  0000000000000000(0000) GS:ffffffff8052a000(0000) knlGS:0000000000000000
CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 00002adb9e51a030 CR3: 000000007ea7e000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process 10.10.10.1-recl (pid: 16353, threadinfo ffff8100467c4000, task ffff8100038ce780)
Stack:  ffff81004aeb6a40 ffff81003cbd1808 ffff81003cbd1808 ffffffff88240b5d
 ffff81000f89b8bc ffff81005fc984e8 ffff81000f89bc30 ffff81005fc984e8
 0000000300000000 0000000000000000 0000000000000000 ffff81003cbd1800
Call Trace:
 [<ffffffff88240b5d>] :nfs:nfs4_xdr_enc_open_noattr+0x6d/0x90
 [<ffffffff881e74b7>] :sunrpc:rpcauth_wrap_req+0x97/0xf0
 [<ffffffff88240af0>] :nfs:nfs4_xdr_enc_open_noattr+0x0/0x90
 [<ffffffff881df57a>] :sunrpc:call_transmit+0x18a/0x290
 [<ffffffff881e5e7b>] :sunrpc:__rpc_execute+0x6b/0x290
 [<ffffffff881dff76>] :sunrpc:rpc_do_run_task+0x76/0xd0
 [<ffffffff882373f6>] :nfs:_nfs4_proc_open+0x76/0x230
 [<ffffffff88237a2e>] :nfs:nfs4_open_recover_helper+0x5e/0xc0
 [<ffffffff88237b74>] :nfs:nfs4_open_recover+0xe4/0x120
 [<ffffffff88238e14>] :nfs:nfs4_open_reclaim+0xa4/0xf0
 [<ffffffff882413c5>] :nfs:nfs4_reclaim_open_state+0x55/0x1b0
 [<ffffffff882417ea>] :nfs:reclaimer+0x2ca/0x390
 [<ffffffff88241520>] :nfs:reclaimer+0x0/0x390
 [<ffffffff8024e59b>] kthread+0x4b/0x80
 [<ffffffff8020cad8>] child_rip+0xa/0x12
 [<ffffffff8024e550>] kthread+0x0/0x80
 [<ffffffff8020cace>] child_rip+0x0/0x12


Code: 0f 0b eb fe 48 89 ef c7 00 00 00 00 02 be 08 00 00 00 e8 79 
RIP  [<ffffffff88240980>] :nfs:encode_open+0x1c0/0x330
 RSP <ffff8100467c5c60>
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

Doh! We can't use cancel_delayed_work_sync because we may have been called
from an unmount that was being performed by nfs_automount_task.
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

I think that I've found and fixed the problem. There is a copy/paste bug in
vt6421_set_dma_mode() function which causes wrong values to be written to
PATA_UDMA_TIMING register.

This patch fixes a copy/paste bug that breaks DMA modes on VT6421 PATA port.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

If you don't terminate a list, bad things happen...
Signed-off-by: NJeff Garzik <jeff@garzik.org>

After my last patch we have a new header file for HP simulator use.
Here's code to use it for stuff that used to have `extern' statements
inline in the code.  Functionality should not change with this patch.
Signed-off-by: NPeter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: NTony Luck <tony.luck@intel.com>

This patch cleans up the `enable early console for SKI' patch
(471e7a44), and
1. potentially allows the gensparse_defconfig to work again.
   (there are other problems running a generic kernel on Ski)
2. fixes the `console registered twice' problem.
3. Cleans up the code by moving the `extern hpsim_cons' declaration to
   a new asm/hpsim.h file.

Thanks to Jes for comments.
Signed-off-by: NPeter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: NTony Luck <tony.luck@intel.com>

When dumping memory via sysrq-m it is possible to take a bogus NMI watchdog
or softlockup watchdog because the dump can take a long time on big memory
systems.

Occasionally tickle the watchdog when doing the dump.
Signed-off-by: NPrarit Bhargava <prarit@redhat.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

Add additional support for CPU disable on SN platforms.
Correctly setup the smp_affinity mask for I/O error IRQs.
Restrict the use of the feature to Altix 4000 and 450 systems
running with a CPU disable capable PROM, and do not allow disabling
of CPU 0.
Signed-off-by: NJohn Keller <jpk@sgi.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

vmalloc() returns a void pointer - no need to cast it.
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

Avoid setting the value if the symbol doesn't need to be changed or can't
be changed. Later choices may change the dependencies and thus the
possible input range.

make oldconfig from a 2.6.22 .config with CONFIG_HOTPLUG_CPU not set
was in some configurations setting CONFIG_HOTPLUG_CPU=y without asking,
even when there was no actual requirement for CONFIG_HOTPLUG_CPU.
This was triggered by SUSPEND_SMP that does a select HOTPLUG_CPU.
Signed-off-by: NRoman Zippel <zippel@linux-m68k.org>
Tested-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup:
  [x86 setup] Don't rely on the VESA BIOS being register-clean

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB/ehca: SRQ fixes to enable IPoIB CM
  IB/ehca: Fix Small QP regressions

This avoids the recent NFS mount regression (returning EBUSY when
mounting the same filesystem twice with different parameters).

The best I can do given the constraints appears to be to have the kernel
first look for a superblock that matches both the fsid and the
user-specified mount options, and then spawn off a new superblock if
that search fails.

Note that this is not the same as specifying nosharecache everywhere
since nosharecache will never attempt to match an existing superblock.
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>
Tested-by: NHua Zhong <hzhong@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

lguest didn't initialize the kernel stack the way a real i386 kernel
does, and ended up triggering a corner-case in the stack frame checking
that doesn't happen on naive i386, and that the stack dumping didn't
handle quite right.

This makes the frame handling more correct, and tries to clarify the
code at the same time so that it's a bit more obvious what is going on.

Thanks to Rusty Russell for debugging the lguest failure-

Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The HPET clocksource in drivers/char/hpet.c was written as generic code
for ia64, but it is not yet ready to replace the native HPET clocksource
implementations that the i386/x86-64 architectures use.

On x86[-64], trying to register this clocksource results in potentially
multiple hpet-based clocksources being registered, and if the ia64 one
is chosen on x86_64 some users have experienced hangs.

Eventually all three architectures may end up using the same code, but
that is not the case right now.

Cc: John Stultz <johnstul@us.ibm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Paolo Ornati <ornati@fastwebnet.it>
Cc: Bob Picco <bob.picco@hp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
  - cxgb3 engine microcode load
  cxgb3 - Fix dev->priv usage
  qeth: Drop ARP packages on HiperSockets interface with NOARP attribute.
  qeth: provide specific message for OSA-adapters exclusively used
  qeth: crash during reboot after failing online setting
  qeth: Announce tx checksumming for qeth devices in TSO/EDDP mode
  qeth: dont return the return values of void functions.
  qeth: enforce a rate limit for inbound scatter gather messages
  qeth: ungrouping a device must not be interruptible
  netxen: fix crashes during module unload
  netxen: Avoid firmware load in PCI probe
  PS3: fix the bug that 'ifconfig down' would hang
  IOC3: Program UART predividers.

Reported by Rick Jones.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix ehca SRQ support so that IPoIB connected mode works:

 - Report max_srq > 0 if SRQ is supported
 - Report "last wqe reached" asynchronous event when base QP dies;
   this is required by the IB spec and IPoIB CM relies on receiving it
   when cleaning up.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The new Small QP code had a few bugs that would also make it trigger
for non-Small QPs.  Fix them.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The VESA BIOS is specified to be register-clean.  However, we have now
found at least one system which violates that.  Thus, be as paranoid
about VESA calls as about everything else.

Huge thanks to Will Simoneau for reporting, diagnosing, and testing
this out on Dell Inspiron 5150.

Cc: Will Simoneau <simoneau@ele.uri.edu>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>