The default_send_IPI_mask_logical() function uses the "flat" APIC mode
to send an IPI to a set of CPU's at once, but if that set happens to be
empty, some older local APIC's will apparently be rather unhappy.  So
just warn if a caller gives us an empty mask, and ignore it.

This fixes a regression in 2.6.30.x, due to commit 4595f962 ("x86:
change flush_tlb_others to take a const struct cpumask"), documented
here:

	http://bugzilla.kernel.org/show_bug.cgi?id=13933

which causes a silent lock-up.  It only seems to happen on PPro, P2, P3
and Athlon XP cores.  Most developers sadly (or not so sadly, if you're
a developer..) have more modern CPU's.  Also, on x86-64 we don't use the
flat APIC mode, so it would never trigger there even if the APIC didn't
like sending an empty IPI mask.
Reported-by: NPavel Vilim <wylda@volny.cz>
Reported-and-tested-by: NThomas Björnell <thomas.bjornell@gmail.com>
Reported-and-tested-by: NMartin Rogge <marogge@onlinehome.de>
Cc: Mike Travis <travis@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'i2c-fixes-rc6' of git://aeryn.fluff.org.uk/bjdooks/linux:
  i2c-stu300: I2C STU300 stability updates
  i2c-omap: Enable workaround for Errata 1.153 based on
  i2c-omap: ACK pending [R/X]DR and [R/X]RDY interrupts
  i2c-omap: Fix I2C status ACK

- blk clk is enabled when an irq arrives. The clk should be enabled,
  but just to make sure.
- All error bits are handled no matter state machine state
- All irq's will run complete() except for irq's that wasn't an event.
- No more looking into status registers just in case an interrupt
  has happend and the irq handle wasn't executed.
- irq_disable/enable are now separete functions.
- clk settings calculation changed to round upwards instead of
  downwards.
- Number of address send attempts before giving up is increased to 12
  from 10 since it most times take 8 tries before getting through.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Silicon Errata 1.153 has been fixed on OMAP 3630|4430 with the use of a later
version of I2C IP block.

The errata impacts OMAP 2420|2430|3430, enable the workaround for these based
on I2C IP block revision number instead of OMAP CPU type
Signed-off-by: NMoiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com
Reviewed-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

ACK any pending read/write interrupts before exiting the ISR either after
completing the operation [ARDY interrupt] or in case of an error
[NACK|AL interrupt]
Signed-off-by: NMoiz Sonasath <m-sonasath@ti.com>
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

I2C status ack for [RX]RDR and [RX]RDY could
cause race conditions of clearing the event
twice and a violation of the programing
sequence as defined in TRM This patch fixes
the same.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NMoiz Sonasath <m-sonasath@ti.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

* 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda - Fix probe of Toshiba laptops with ALC268 codec
  ALSA: hda: add model for Intel DG45ID/DG45FC boards
  ALSA: hda: enable speaker output for Compaq 6530s/6531s

There are many variants of Toshiba laptops with ALC268 codec, and
it seems that a few of them don't work with model=toshiba preset
since they have the secondary ALC268 codec just for HDMI output.
This is a regression due to the previous clean-up work to merge all
Toshiba quirk entries into a single check.

This patch adds the identification of such laptops to apply the
standard BIOS-probing method.  Unfortunately, Toshiba laptops have
all the same PCI SSID, so we need to check the codec SSID to identify
each device.
Tested-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
  nilfs2: fix oopses with doubly mounted snapshots
  nilfs2: missing a read lock for segment writer in nilfs_attach_checkpoint()

Fix some issues with the AFS documentation, found when testing AFS on ppc64:

- Update AFS features: reading/writing, local caching
- Typo in kafs sysfs debug file
- Use modprobe instead of insmod in example
- Update IPs for grand.central.org
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/kms: teardown crtc correctly when fb is destroyed.
  drm/kms/radeon: cleanup combios TV table like DDX.
  drm/radeon/kms: memset the allocated framebuffer before using it.
  drm/radeon/kms: although LVDS might be possible on crtc 1 don't do it.
  drm/radeon/kms: implement bo busy check + current domain
  drm/radeon/kms: cut down indirects in register accesses.
  drm/radeon/kms: Fix up vertical blank interrupt support.
  drm/radeon/kms: add rv530 R300_SU_REG_DEST + reloc for ZPASS_ADDR
  drm/edid: fixup detailed timings like the X server.
  drm/radeon/kms: Add specific rs690 authorized register table

* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: Update Microblaze defconfigs
  microblaze: Use klimit instead of _end for memory init
  microblaze: Enable ppoll syscall
  microblaze: Sane handling of missing timer/intc in device tree
  microblaze: use the generic ack_bad_irq implementation

Merge branch 'perfcounters-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perfcounters-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf tools: Make 'make html' work
  perf annotate: Fix segmentation fault
  perf_counter: Fix the PARISC build
  perf_counter: Check task on counter read IPI
  perf: Rename perf-examples.txt to examples.txt
  perf record: Fix typo in pid_synthesize_comm_event

The BIOS pin configs are in fact correct and shall not be overwritten.
Signed-off-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

HP Compaq 6530s and 6531s internal speaker is silence or becomes silence
within 1 minute after fresh boot. It is found that pin 0x1c must be set to
PIN_OUT mode to make the speaker work. This is weird - line-in pin 0x1c and
speaker pin 0x16 seem to be unrelated.

The codec differences before/after patch are:

@@ Node 0x17 [Pin Complex] wcaps 0x40020b:
   Pin Default 0x41a6e130: [N/A] Mic at Ext Rear
     Conn = Digital, Color = White
     DefAssociation = 0x3, Sequence = 0x0
     Misc = NO_PRESENCE
-  Pin-ctls: 0x24: IN
+  Pin-ctls: 0x40: OUT
@@ Node 0x1c [Pin Complex] wcaps 0x40018d:
   Pin Default 0x41813021: [N/A] Line In at Ext Rear
     Conn = 1/8, Color = Blue
     DefAssociation = 0x2, Sequence = 0x1
-  Pin-ctls: 0x24: IN VREF_80
+  Pin-ctls: 0x40: OUT VREF_HIZ
   Unsolicited: tag=00, enabled=0
   Connection: 1
      0x24

Tests show that it won't impact (external) Mic recording.
Reported-by: N"Lin, Ming M" <ming.m.lin@intel.com>
Signed-off-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

If userspace destroys a framebuffer that is in use on a crtc,
don't just null it out, tear down the crtc properly so the
hw gets turned off.
Signed-off-by: NDave Airlie <airlied@redhat.com>

The fallback case wasn't getting executed properly if there
was no TV table, which my T42 M7 hasn't got.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This gets rid of some ugliness, we shuold probably find a way
for the GPU to zero this.
Signed-off-by: NDave Airlie <airlied@redhat.com>

LVDS always requests RMX_FULL, we need to fix it so that doesn't happen
before we can enable LVDS on crtc 1.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  security: Fix prompt for LSM_MMAP_MIN_ADDR
  security: Make LSM_MMAP_MIN_ADDR default match its help text.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
  percpu: use the right flag for get_vm_area()
  percpu, sparc64: fix sparse possible cpu map handling
  init: set nr_cpu_ids before setup_per_cpu_areas()

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, mce: Don't initialize MCEs on unknown CPUs
  x86, mce: don't log boot MCEs on Pentium M (model == 13) CPUs
  x86: Annotate section mismatch warnings in kernel/apic/x2apic_uv_x.c
  x86, mce: therm_throt: Don't log redundant normality
  x86: Fix UV BAU destination subnode id

If node_load[] is cleared everytime build_zonelists() is
called,node_load[] will have no help to find the next node that should
appear in the given node's fallback list.

Because of the bug, zonelist's node_order is not calculated as expected.
This bug affects on big machine, which has asynmetric node distance.

[synmetric NUMA's node distance]
     0    1    2
0   10   12   12
1   12   10   12
2   12   12   10

[asynmetric NUMA's node distance]
     0    1    2
0   10   12   20
1   12   10   14
2   20   14   10

This (my bug) is very old but no one has reported this for a long time.
Maybe because the number of asynmetric NUMA is very small and they use
cpuset for customizing node memory allocation fallback.

[akpm@linux-foundation.org: fix CONFIG_NUMA=n build]
Signed-off-by: NBo Liu <bo-liu@hotmail.com>
Reviewed-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

According to the POSIX (1003.1-2008), the file descriptor shall have been
opened with read permission, regardless of the protection options specified to
mmap().  The ltp test cases mmap06/07 need this.
Signed-off-by: NGraff Yang <graff.yang@gmail.com>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NGreg Ungerer <gerg@snapgear.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since the changes to the bitbang driver, there is the possibility we will
be called with either the speed_hz or bpw values zero.  We take these to
mean that the default values (8 bits per word, or maximum bus speed).
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently the clock rate calculation may round as pleased, which means
that it is possible that we will round down and end up with a faster clock
rate than intended.

Change the calculation to use DIV_ROUND_UP() to ensure that we end up with
a clock rate either the same as or lower than the user requested one.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There are a number of individual MMC drivers listed in MAINTAINERS.  I
didn't modify those records.  Perhaps I should have.

Cc: <linux-mmc@vger.kernel.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Nicolas Pitre <nico@cam.org>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: Pavel Pisa <ppisa@pikron.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Sascha Sommer <saschasommer@freenet.de>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The commit 2ff05b2b (oom: move oom_adj value) moveed the oom_adj value to
the mm_struct.  It was a very good first step for sanitize OOM.

However Paul Menage reported the commit makes regression to his job
scheduler.  Current OOM logic can kill OOM_DISABLED process.

Why? His program has the code of similar to the following.

	...
	set_oom_adj(OOM_DISABLE); /* The job scheduler never killed by oom */
	...
	if (vfork() == 0) {
		set_oom_adj(0); /* Invoked child can be killed */
		execve("foo-bar-cmd");
	}
	....

vfork() parent and child are shared the same mm_struct.  then above
set_oom_adj(0) doesn't only change oom_adj for vfork() child, it's also
change oom_adj for vfork() parent.  Then, vfork() parent (job scheduler)
lost OOM immune and it was killed.

Actually, fork-setting-exec idiom is very frequently used in userland program.
We must not break this assumption.

Then, this patch revert commit 2ff05b2b and related commit.

Reverted commit list
---------------------
- commit 2ff05b2b (oom: move oom_adj value from task_struct to mm_struct)
- commit 4d8b9135 (oom: avoid unnecessary mm locking and scanning for OOM_DISABLE)
- commit 81236810 (oom: only oom kill exiting tasks with attached memory)
- commit 933b787b (mm: copy over oom_adj value at fork time)
Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Paul Menage <menage@google.com>
Cc: David Rientjes <rientjes@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

get_sb_pseudo sets s_maxbytes to ~0ULL which becomes negative when cast
to a signed value.  Fix it to use MAX_LFS_FILESIZE which casts properly
to a positive signed value.
Signed-off-by: NJeff Layton <jlayton@redhat.com>
Reviewed-by: NJohannes Weiner <hannes@cmpxchg.org>
Acked-by: NSteve French <smfrench@gmail.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Robert Love <rlove@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NBenny Halevy <bhalevy@panasas.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix prompt for LSM_MMAP_MIN_ADDR.

(Verbs are cool!)
Signed-off-by: NAndreas Schwab <schwab@linux-m68k.org>
Acked-by: NEric Paris <eparis@redhat.com>
Signed-off-by: NJames Morris <jmorris@namei.org>

Commit 788084ab added the LSM_MMAP_MIN_ADDR
option, whose help text states "For most ia64, ppc64 and x86 users with lots
of address space a value of 65536 is reasonable and should cause no problems."
Which implies that it's default setting was typoed.
Signed-off-by: NDave Jones <davej@redhat.com>
Acked-by: NEric Paris <eparis@redhat.com>
Signed-off-by: NJames Morris <jmorris@namei.org>

Merge branch 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  genirq: Wake up irq thread after action has been installed

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (60 commits)
  net: restore gnet_stats_basic to previous definition
  NETROM: Fix use of static buffer
  e1000e: fix use of pci_enable_pcie_error_reporting
  e1000e: WoL does not work on 82577/82578 with manageability enabled
  cnic: Fix locking in init/exit calls.
  cnic: Fix locking in start/stop calls.
  bnx2: Use mutex on slow path cnic calls.
  cnic: Refine registration with bnx2.
  cnic: Fix symbol_put_addr() panic on ia64.
  gre: Fix MTU calculation for bound GRE tunnels
  pegasus: Add new device ID.
  drivers/net: fixed drivers that support netpoll use ndo_start_xmit()
  via-velocity: Fix test of mii_status bit VELOCITY_DUPLEX_FULL
  rt2x00: fix memory corruption in rf cache, add a sanity check
  ixgbe: Fix receive on real device when VLANs are configured
  ixgbe: Do not return 0 in ixgbe_fcoe_ddp() upon FCP_RSP in DDP completion
  netxen: free napi resources during detach
  netxen: remove netxen workqueue
  ixgbe: fix issues setting rx-usecs with legacy interrupts
  can: fix oops caused by wrong rtnl newlink usage
  ...

* 'sh/for-2.6.31' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh: sh7724 ddr self-refresh changes
  sh: use in-soc KEYSC on se7724
  sh: CMT suspend/resume
  sh: skip disabled LCDC channels

* 'for-linus' of git://neil.brown.name/md:
  Fix new incorrect error return from do_md_stop.

will fix kernel oopses like the following:

 # mount -t nilfs2 -r -o cp=20 /dev/sdb1 /test1
 # mount -t nilfs2 -r -o cp=20 /dev/sdb1 /test2
 # umount /test1
 # umount /test2

BUG: sleeping function called from invalid context at arch/x86/mm/fault.c:1069
in_atomic(): 0, irqs_disabled(): 1, pid: 3886, name: umount.nilfs2
1 lock held by umount.nilfs2/3886:
 #0:  (&type->s_umount_key#31){+.+...}, at: [<c10b398a>] deactivate_super+0x52/0x6c
irq event stamp: 1219
hardirqs last  enabled at (1219): [<c135c774>] __mutex_unlock_slowpath+0xf8/0x119
hardirqs last disabled at (1218): [<c135c6d5>] __mutex_unlock_slowpath+0x59/0x119
softirqs last  enabled at (1214): [<c1033316>] __do_softirq+0x1a5/0x1ad
softirqs last disabled at (1205): [<c1033354>] do_softirq+0x36/0x5a
Pid: 3886, comm: umount.nilfs2 Not tainted 2.6.31-rc6 #55
Call Trace:
 [<c1023549>] __might_sleep+0x107/0x10e
 [<c13603c0>] do_page_fault+0x246/0x397
 [<c136017a>] ? do_page_fault+0x0/0x397
 [<c135e753>] error_code+0x6b/0x70
 [<c136017a>] ? do_page_fault+0x0/0x397
 [<c104f805>] ? __lock_acquire+0x91/0x12fd
 [<c1050a62>] ? __lock_acquire+0x12ee/0x12fd
 [<c1050a62>] ? __lock_acquire+0x12ee/0x12fd
 [<c1050b2b>] lock_acquire+0xba/0xdd
 [<d0d17d3f>] ? nilfs_detach_segment_constructor+0x2f/0x2fa [nilfs2]
 [<c135d4fe>] down_write+0x2a/0x46
 [<d0d17d3f>] ? nilfs_detach_segment_constructor+0x2f/0x2fa [nilfs2]
 [<d0d17d3f>] nilfs_detach_segment_constructor+0x2f/0x2fa [nilfs2]
 [<c104ea2c>] ? mark_held_locks+0x43/0x5b
 [<c104ecb1>] ? trace_hardirqs_on_caller+0x10b/0x133
 [<c104ece4>] ? trace_hardirqs_on+0xb/0xd
 [<d0d09ac1>] nilfs_put_super+0x2f/0xca [nilfs2]
 [<c10b3352>] generic_shutdown_super+0x49/0xb8
 [<c10b33de>] kill_block_super+0x1d/0x31
 [<c10e6599>] ? vfs_quota_off+0x0/0x12
 [<c10b398f>] deactivate_super+0x57/0x6c
 [<c10c4bc3>] mntput_no_expire+0x8c/0xb4
 [<c10c5094>] sys_umount+0x27f/0x2a4
 [<c10c50c6>] sys_oldumount+0xd/0xf
 [<c10031a4>] sysenter_do_call+0x12/0x38
 ...

This turns out to be a bug brought by an -rc1 patch ("nilfs2: simplify
remaining sget() use").

In the patch, a new "put resource" function, nilfs_put_sbinfo()
was introduced to delay freeing nilfs_sb_info struct.

But the nilfs_put_sbinfo() mistakenly used atomic_dec_and_test()
function to check the reference count, and it caused the nilfs_sb_info
was freed when user mounted a snapshot twice.

This bug also suggests there was unseen memory leak in usual mount
/umount operations for nilfs.
Signed-off-by: NRyusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>

pushd tools/perf/Documentation
make html
popd

is failing for me...

    ASCIIDOC perf-annotate.html
ERROR: unsafe: include file: /etc/asciidoc/./stylesheets/xhtml11.css
ERROR: unsafe: include file:
/etc/asciidoc/./stylesheets/xhtml11-manpage.css
ERROR: unsafe: include file:
/etc/asciidoc/./stylesheets/xhtml11-quirks.css
make: *** [perf-annotate.html] Error 1

Apparently asciidoc "unsafe" is the default mode of operation
in practice.

https://bugzilla.redhat.com/show_bug.cgi?id=506953

Works tidily now.
Signed-off-by: NKyle McMartin <kyle@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20090818164125.GM25206@bombadil.infradead.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The wake_up_process() of the new irq thread in __setup_irq() is too
early as the irqaction is not yet fully initialized especially
action->irq is not yet set. The interrupt thread might dereference the
wrong irq descriptor.

Move the wakeup after the action is installed and action->irq has been
set.
Reported-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NMichael Buesch <mb@bu3sch.de>