This patch adds a check and message if the device is in
MFP mode as changing RSS input set is not supported in
MFP mode.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Changes parsing of FW 4.33 AQ command Get CEE DCBX OPER CFG (0x0A07).
Change is required because FW now creates the oper_prio_tc
nibbles reversed from those in the CEE Priority Group sub-TLV.
This change will only apply to FW 4.33 as future FW versions will use a
different function to parse the CEE data.
Signed-off-by: NGreg Bowers <gregory.j.bowers@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This is a fix for the static code analysis issue where dcbcfg->numapps
could be greater than size of array (i.e dcbcfg->app[I40E_DCBX_MAX_APPS]).
The fix makes sure that the array is not accessed past the size of
of the array (i.e. I40E_DCBX_MAX_APPS).

Copyright updated to 2017.
Signed-off-by: NSudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The firmware expects the port number passed when setting up
the UDP tunnel configuration to be in Little Endian format.
The i40e_aq_add_udp_tunnel command byte swaps the value from
host order to Little Endian.

Since commit fe0b0cd9 ("i40e: send correct port number to
AdminQ when enabling UDP tunnels") we've correctly
sent the value in host order.

Let's also add a comment to the function explaining that it must
be in host order, as the port numbers are commonly stored as Big
Endian values.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When searching for the vf_capability client routine, dev_info() was
used, instead of the normal dev_dbg(). This causes the message to be
displayed at standard log levels which can cause administrators to
worry. Avoid this by using dev_dbg instead.

Copyright updated to 2017.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update a few flags related to FW interactions.

Copyright updated to 2017.
Signed-off-by: NAlice Michael <alice.michael@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The variable num_active_queues represents the number of active queues we
have for the device. We assign this pretty early in i40evf_init_subtask.

Several code locations are written with loops over the tx_rings and
rx_rings structures, which don't get allocated until
i40evf_alloc_queues, and which get freed by i40evf_free_queues.

These call sites were written under the assumption that tx_rings and
rx_rings would always be allocated at least when num_active_queues is
non-zero.

Lets fix this by moving the assignment into the function where we
allocate queues. We'll use a temporary variable for storage so that we
don't assign the value in the adapter structure until after the rings
have been set up.

Finally, when we free the queues, we'll clear the value to ensure that
we do not loop over the rings memory that no longer exists.

This resolves a possible NULL pointer dereference in
i40evf_get_ethtool_stats which could occur if the VF fails to recover
from a reset, and then a user requests statistics.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds proper XDP_TX action support. For each Tx ring, an
additional XDP Tx ring is allocated and setup. This version does the
DMA mapping in the fast-path, which will penalize performance for
IOMMU enabled systems. Further, debugfs support is not wired up for
the XDP Tx rings.
Signed-off-by: NBjörn Töpel <bjorn.topel@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This commit adds basic XDP support for i40e derived NICs. All XDP
actions will end up in XDP_DROP.
Signed-off-by: NBjörn Töpel <bjorn.topel@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When a s390 guest runs on a z/VM host that's part of a SSI cluster,
it can be migrated to a different host. In this case, the MAC address
it originally obtained on the old host may be re-assigned to a new
guest. This would result in address conflicts between the two guests.

When running as z/VM guest, use the diag26c MAC Service to obtain
a hypervisor-managed MAC address. The MAC Service is SSI-aware, and
won't re-assign the address after the guest is migrated to a new host.

This patch adds support for the z/VM MAC Service on L2 devices.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's two spots in qeth_send_packet() where we don't accurately
account for transmitted packing buffers in qeth's performance
statistics:

1) when flushing the current buffer due to insufficient size,
   and the next buffer is not EMPTY, we need to account for that
   flushed buffer.
2) when synchronizing with the TX completion code, we reset
   flush_count and thus forget to account for any previously
   flushed buffers.
Reported-by: NNils Hoppmann <niho@de.ibm.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

add ipa return codes for Bridgeport (HiperSockets and OSA) according to
system level design.
Signed-off-by: NKittipon Meesompop <kmeesomp@linux.vnet.ibm.com>
Reviewed-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With -Wformat-truncation, gcc throws the following warning.

Fix this by increasing the size of devname to accommodate 15 character
netdev interface name and description.

Remove length format precision for %s. We can fit entire name.

Also increment the version.

drivers/net/ethernet/cisco/enic/enic_main.c: In function ‘enic_open’:
drivers/net/ethernet/cisco/enic/enic_main.c:1740:15: warning: ‘%u’ directive output may be truncated writing between 1 and 2 bytes into a region of size between 1 and 12 [-Wformat-truncation=]
     "%.11s-rx-%u", netdev->name, i);
               ^~
drivers/net/ethernet/cisco/enic/enic_main.c:1740:5: note: directive argument in the range [0, 16]
     "%.11s-rx-%u", netdev->name, i);
     ^~~~~~~~~~~~~
drivers/net/ethernet/cisco/enic/enic_main.c:1738:4: note: ‘snprintf’ output between 6 and 18 bytes into a destination of size 16
    snprintf(enic->msix[intr].devname,
    ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
     sizeof(enic->msix[intr].devname),
     ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
     "%.11s-rx-%u", netdev->name, i);
     ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: NGovindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is nothing in the IP that prevents us from enabling TSO for IPv6.

Before patch:
ftp fe80::2aa:bbff:fecc:1336%eth0
ftp> get /dev/zero
882512708 bytes received in 00:14 (56.11 MiB/s)

After patch:
ftp fe80::2aa:bbff:fecc:1336%eth0
ftp> get /dev/zero
1203326784 bytes received in 00:12 (94.52 MiB/s)
Signed-off-by: NNiklas Cassel <niklas.cassel@axis.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the ibmvnic driver is not in the VNIC_OPEN state, return from
ibmvnic_resume callback. If we are not in the VNIC_OPEN state, interrupts
may not be initialized and directly calling the interrupt handler will
cause a crash.
Signed-off-by: NJohn Allen <jallen@linux.vnet.ibm.com>
Reviewed-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Provide link partner advertising information.
Removed testing for gigabit modes, which is useless for a fast ethernet phy.
Signed-off-by: NThomas Bogendoerfer <tbogendoerfer@suse.de>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The get_rps_cpu() function will not do any RPS on the data flow when no
queue is setup and always use the current cpu where the IRQ was handled
to also handle the backlog. As we only have one physical queue we always
set this to 0 unconditionally.
Signed-off-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Originally the driver only utilised the new QDMA engine. The current code
still assumes this is the case when locking the IRQ mask register. Since
RX now runs on the old style PDMA engine we can add a second lock. This
patch reduces the IRQ latency as the TX and RX path no longer need to wait
on each other under heavy load.
Signed-off-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PDMA engine used for RX allows IRQ aggregation. The patch sets up the
corresponding registers to aggregate 4 IRQs into one. Using aggregation
reduces the load on the core handling to a quarter thus reducing IRQ
latency and increasing RX performance by around 10%.
Signed-off-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently PHY status changes are only printed for DSA ports. This patch
adds code to also print status changes for non-fixed links.
Signed-off-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As link-local addresses are only valid for a single interface, we can allow
to use the same VNI for multiple independent VXLANs, as long as the used
interfaces are distinct. This way, VXLANs can always be used as a drop-in
replacement for VLANs with greater ID space.

This also extends VNI lookup to respect the ifindex when link-local IPv6
addresses are used, so using the same VNI on multiple interfaces can
actually work.
Signed-off-by: NMatthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If VXLAN is run over link-local IPv6 addresses, it is necessary to store
the ifindex in the FDB entries. Otherwise, the used interface is undefined
and unicast communication will most likely fail.

Support for link-local IPv4 addresses should be possible as well, but as
the semantics aren't as well defined as for IPv6, and there doesn't seem to
be much interest in having the support, it's not implemented for now.
Signed-off-by: NMatthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* Multicast addresses are never valid as local address
* Link-local IPv6 unicast addresses may only be used as remote when the
  local address is link-local as well
* Don't allow link-local IPv6 local/remote addresses without interface

We also store in the flags field if link-local addresses are used for the
follow-up patches that actually make VXLAN over link-local IPv6 work.
Signed-off-by: NMatthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Address families of source and destination addresses must match, and
changelink operations can't change the address family.

In addition, always use the VXLAN_F_IPV6 to check if a VXLAN device uses
IPv4 or IPv6.
Signed-off-by: NMatthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no good reason to keep the flags twice in vxlan_dev and
vxlan_config.
Signed-off-by: NMatthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The vxlan_dev_configure function was mixing validation and application of
the vxlan configuration; this could easily lead to bugs with the changelink
operation, as it was hard to see if the function wcould return an error
after parts of the configuration had already been applied.

This commit splits validation and application out of vxlan_dev_configure as
separate functions to make it clearer where error returns are allowed and
where the vxlan_dev or net_device may be configured. Log messages in these
functions are removed, as it is generally unexpected to find error output
for netlink requests in the kernel log. Userspace should be able to handle
errors based on the error codes returned via netlink just fine.

In addition, some validation and initialization is moved to vxlan_validate
and vxlan_setup respectively to improve grouping of similar settings.

Finally, this also fixes two actual bugs:

* if set, conf->mtu would overwrite dev->mtu in each changelink operation,
  reverting other changes of dev->mtu
* the "if (!conf->dst_port)" branch would never be run, as conf->dst_port
  was set in vxlan_setup before. This caused VXLAN-GPE to use the same
  default port as other VXLAN sockets instead of the intended IANA-assigned
  4790.
Signed-off-by: NMatthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: Nyuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

spatch file,
@@
expression skb, len, data;
type t;
@@
-memcpy((t *)skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);

@@
identifier p;
expression skb, len, data;
type t;
@@
-p = (t *)memset(skb_put(skb, len), data, len);
+p = skb_put_zero(skb, len);

@@
expression skb, len, data;
type t;
@@
-memcpy((t *)__skb_put(skb, len), data, len);
+__skb_put_data(skb, data, len);

@@
identifier p;
expression skb, len, data;
type t;
@@
-p = (t *)memset(__skb_put(skb, len), data, len);
+p = __skb_put_zero(skb, len);
Signed-off-by: Nyuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

follow Johannes Berg, semantic patch file as below,
@@
identifier p, p2;
expression len;
expression skb;
type t, t2;
@@
(
-p = __skb_put(skb, len);
+p = __skb_put_zero(skb, len);
|
-p = (t)__skb_put(skb, len);
+p = __skb_put_zero(skb, len);
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, len);
|
-memset(p, 0, len);
)

@@
identifier p;
expression len;
expression skb;
type t;
@@
(
-t p = __skb_put(skb, len);
+t p = __skb_put_zero(skb, len);
)
... when != p
(
-memset(p, 0, len);
)

@@
type t, t2;
identifier p, p2;
expression skb;
@@
t *p;
...
(
-p = __skb_put(skb, sizeof(t));
+p = __skb_put_zero(skb, sizeof(t));
|
-p = (t *)__skb_put(skb, sizeof(t));
+p = __skb_put_zero(skb, sizeof(t));
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, sizeof(*p));
|
-memset(p, 0, sizeof(*p));
)

@@
expression skb, len;
@@
-memset(__skb_put(skb, len), 0, len);
+__skb_put_zero(skb, len);

@@
expression skb, len, data;
@@
-memcpy(__skb_put(skb, len), data, len);
+__skb_put_data(skb, data, len);

@@
expression SKB, C, S;
typedef u8;
identifier fn = {__skb_put};
fresh identifier fn2 = fn ## "_u8";
@@
- *(u8 *)fn(SKB, S) = C;
+ fn2(SKB, C);
Signed-off-by: Nyuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Kill the remaining shift macro in favor of calculating at compile time
its value from the more descriptive mask, which gives us a better
representation of the register layout.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prefix and document the remaining Global 2 registers macros.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Marvell 88E6352 family has a Global 2 register dedicated to the
watchdog setup. But the 88E6390 turned it into an indirect table.

Prefix and document that.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prefix and document the Global 2 Switch MAC registers macros.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prefix and document the Global 2 EEPROM registers macros.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prefix and document the Global 2 Cross-chip Port VLAN registers macros.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prefix and document the Global 2 MGMT registers macros.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prefix and document the Global 2 Device Mapping macros.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prefix and document the Global 2 Trunk registers macros. At the same
time, fix the hask -> hash typo and use the mv88e6xxx_port_mask helper.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marvell chips with an SMI PHY access in Global 2 registers handle both
Clause 22 and Clause 45 of IEEE 802.3.

The 88E6390 family has addition bits to target the internal or external
PHYs connected to the device, and a Setup function in addition to the
default (register) Access function.

Prefix the SMI PHY Command and Data registers macros, implement clear
helpers for Clause 22 and 44 Access functions, rename variable to match
the SMI and switch vocabulary (device and register addresses for Clause
22 and port and device class for Clause 45.)

Finally do not use complex macros but simple 16-bit mask to document the
registers organization.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some Marvell chips have an Ingress Rate Limit unit. But the command
values slightly differs between models: 88E6352 use 3-bit for operations
while 88E6390 use different 2-bit operations.

This commit kills the IRL flags in favor of a new operation implementing
the "Init all resources to the initial state" operation.

This fixes the operation of 88E6390 family where 0x1000 means Read the
selected resource 0, register 0 on port 16, instead of init all.

A mv88e6xxx_irl_setup helper is added to wrap the operation call.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>