Rework probe to group common hw initialization:
- group resources request at the beginning of the probe
- move net device initialization and registration at the end of the probe
- drop cpsw_slave_init
as preparation of refactoring of common hw initialization code to
separate function.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Davinci MDIO in most of the case implemented as module inside of TI
CPSW subsystem and fully depends on CPSW to be enabled, but historically
it's implemented as separate Platform device/driver and defined in DT files
in two ways:
- as standalone node
- as child node of CPSW subsystem.

In later case it's required to split CPSW subsystem "reg" property to
exclude MDIO I/O range which is not useful.

Hence, replace devm_ioremap_resource() with devm_ioremap() to allow define
full I/O range in parent CPSW subsystem without spliting.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do not delete multicast supervisory packet's (SUPER) entries while flushing
multicast addresses from ALE table cpsw_ale_flush_multicast(). Those
entries have to be added/removed only explicitly.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now CPSW ALE will set/clean Host port bit in Unregistered Multicast Flood
Mask (UNREG_MCAST_FLOOD_MASK) for every VLAN without checking if this port
belongs to VLAN or not when ALLMULTI mode flag is set for nedev. This is
working in non dual_mac mode, but in dual_mac - it causes
enabling/disabling ALLMULTI flag for both ports.

Hence fix it by adding additional parameter to cpsw_ale_set_allmulti() to
specify ALE port number for which ALLMULTI has to be enabled and check if
port belongs to VLAN before modifying UNREG_MCAST_FLOOD_MASK.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use ALE_PORT_HOST define for host port in cpsw_ale_set_allmulti() instead
of constants.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use correct define ALE_SUPER for ALE Multicast Address Table Entry
Supervisory Packet (SUPER) bit setting instead of ALE_BLOCKED. No issues
were observed till now as it have never been set, but it's going to be used
by new CPSW switch driver.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drop unnecessary wrapper function cpsw_tx_packet_submit() which is used
only in one place.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use devm_alloc_etherdev_mqs() and simplify code.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drop pinctrl_pm_select_default_state call from probe as default
pinctrl state is set by DD core.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use local variable struct device *dev in probe to simplify code.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update cpsw_split_res() to accept struct cpsw_common instead of
struct net_device to simplify code.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All TI drivers CPSW/NETCP can't work without ALE, hence simplify
build of those drivers by always linking cpsw_ale and drop
CONFIG_TI_CPSW_ALE config option.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Both drivers CPSW and EMAC can't work without CPDMA, hence simplify build
of those drivers by always linking davinci_cpdma and drop TI_DAVINCI_CPDMA
config option.
Note. the davinci_emac driver module was changed to "ti_davinci_emac" to
make build work.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace textual license with SPDX-License-Identifier.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add options to strictly validate messages and dump messages,
sometimes perhaps validating dump messages non-strictly may
be required, so add an option for that as well.

Since none of this can really be applied to existing commands,
set the options everwhere using the following spatch:

    @@
    identifier ops;
    expression X;
    @@
    struct genl_ops ops[] = {
    ...,
     {
            .cmd = X,
    +       .validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
            ...
     },
    ...
    };

For new commands one should just not copy the .validate 'opt-out'
flags and thus get strict validation.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We currently have two levels of strict validation:

 1) liberal (default)
     - undefined (type >= max) & NLA_UNSPEC attributes accepted
     - attribute length >= expected accepted
     - garbage at end of message accepted
 2) strict (opt-in)
     - NLA_UNSPEC attributes accepted
     - attribute length >= expected accepted

Split out parsing strictness into four different options:
 * TRAILING     - check that there's no trailing data after parsing
                  attributes (in message or nested)
 * MAXTYPE      - reject attrs > max known type
 * UNSPEC       - reject attributes with NLA_UNSPEC policy entries
 * STRICT_ATTRS - strictly validate attribute size

The default for future things should be *everything*.
The current *_strict() is a combination of TRAILING and MAXTYPE,
and is renamed to _deprecated_strict().
The current regular parsing has none of this, and is renamed to
*_parse_deprecated().

Additionally it allows us to selectively set one of the new flags
even on old policies. Notably, the UNSPEC flag could be useful in
this case, since it can be arranged (by filling in the policy) to
not be an incompatible userspace ABI change, but would then going
forward prevent forgetting attribute entries. Similar can apply
to the POLICY flag.

We end up with the following renames:
 * nla_parse           -> nla_parse_deprecated
 * nla_parse_strict    -> nla_parse_deprecated_strict
 * nlmsg_parse         -> nlmsg_parse_deprecated
 * nlmsg_parse_strict  -> nlmsg_parse_deprecated_strict
 * nla_parse_nested    -> nla_parse_nested_deprecated
 * nla_validate_nested -> nla_validate_nested_deprecated

Using spatch, of course:
    @@
    expression TB, MAX, HEAD, LEN, POL, EXT;
    @@
    -nla_parse(TB, MAX, HEAD, LEN, POL, EXT)
    +nla_parse_deprecated(TB, MAX, HEAD, LEN, POL, EXT)

    @@
    expression NLH, HDRLEN, TB, MAX, POL, EXT;
    @@
    -nlmsg_parse(NLH, HDRLEN, TB, MAX, POL, EXT)
    +nlmsg_parse_deprecated(NLH, HDRLEN, TB, MAX, POL, EXT)

    @@
    expression NLH, HDRLEN, TB, MAX, POL, EXT;
    @@
    -nlmsg_parse_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
    +nlmsg_parse_deprecated_strict(NLH, HDRLEN, TB, MAX, POL, EXT)

    @@
    expression TB, MAX, NLA, POL, EXT;
    @@
    -nla_parse_nested(TB, MAX, NLA, POL, EXT)
    +nla_parse_nested_deprecated(TB, MAX, NLA, POL, EXT)

    @@
    expression START, MAX, POL, EXT;
    @@
    -nla_validate_nested(START, MAX, POL, EXT)
    +nla_validate_nested_deprecated(START, MAX, POL, EXT)

    @@
    expression NLH, HDRLEN, MAX, POL, EXT;
    @@
    -nlmsg_validate(NLH, HDRLEN, MAX, POL, EXT)
    +nlmsg_validate_deprecated(NLH, HDRLEN, MAX, POL, EXT)

For this patch, don't actually add the strict, non-renamed versions
yet so that it breaks compile if I get it wrong.

Also, while at it, make nla_validate and nla_parse go down to a
common __nla_validate_parse() function to avoid code duplication.

Ultimately, this allows us to have very strict validation for every
new caller of nla_parse()/nlmsg_parse() etc as re-introduced in the
next patch, while existing things will continue to work as is.

In effect then, this adds fully strict validation for any new command.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Even if the NLA_F_NESTED flag was introduced more than 11 years ago, most
netlink based interfaces (including recently added ones) are still not
setting it in kernel generated messages. Without the flag, message parsers
not aware of attribute semantics (e.g. wireshark dissector or libmnl's
mnl_nlmsg_fprintf()) cannot recognize nested attributes and won't display
the structure of their contents.

Unfortunately we cannot just add the flag everywhere as there may be
userspace applications which check nlattr::nla_type directly rather than
through a helper masking out the flags. Therefore the patch renames
nla_nest_start() to nla_nest_start_noflag() and introduces nla_nest_start()
as a wrapper adding NLA_F_NESTED. The calls which add NLA_F_NESTED manually
are rewritten to use nla_nest_start().

Except for changes in include/net/netlink.h, the patch was generated using
this semantic patch:

@@ expression E1, E2; @@
-nla_nest_start(E1, E2)
+nla_nest_start_noflag(E1, E2)

@@ expression E1, E2; @@
-nla_nest_start_noflag(E1, E2 | NLA_F_NESTED)
+nla_nest_start(E1, E2)
Signed-off-by: NMichal Kubecek <mkubecek@suse.cz>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's meaningless to trigger reset when failed to send command to IMP,
because the failure is usually caused by no authority, illegal command
and so on. When that happened, we just need to return the status code
for further debugging.
Signed-off-by: NWeihang Li <liweihang@hisilicon.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a check for the hns3_put_ring_config() to prevent
double free, and for more readable, move the NULL assignment of
priv->ring_data into the hns3_put_ring_config().
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The test results show that the maximum time of hardware return
to mac link state is 500MS.The software needs to set twice the
maximum time of hardware return state (1000MS).

If not modified, the loopback test returns probability failure.
Signed-off-by: Nliuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When configure pause, current implementation returns directly
after setup PFC without setup BP, which is not sufficient.

So this patch fixes it, only return while setting PFC failed.

Fixes: 44e59e37 ("net: hns3: do not return GE PFC setting err when initializing")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the hardware does not handle mailboxes and the hardware
reset include TQP reset, so it is unnecessary to reset TQP
in the hclgevf_ae_stop() while doing VF reset. Also it is
unnecessary to reset the remaining TQP when one reset fails.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch uses a reserved byte in the hclge_mbx_vf_to_pf_cmd
to save the need_resp flag, so when PF received the mailbox,
it can use it to decise whether send a response to VF.

For hclge_set_vf_uc_mac_addr(), it should use mbx_need_resp flag
to decide whether send response to VF.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since irq handler and mailbox task will both update arq's count,
so arq's count should use atomic_t instead of u32, otherwise
its value may go wrong finally.

Fixes: 07a0556a ("net: hns3: Changes to support ARQ(Asynchronous Receive Queue)")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HCLGEVF_STATE_CMD_DISABLE is more suitable than
HCLGEVF_STATE_RST_HANDLING to stop sending keep alive msg,
since HCLGEVF_STATE_RST_HANDLING only be set when the reset
task is running.

Fixes: c59a85c0 ("net: hns3: stop sending keep alive msg to PF when VF is resetting")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bdinfo handled in hns3_handle_bdinfo is only valid on the
last BD of the current packet, currently the bd info may be handled
based on the first BD if the packet has more than two BDs, which
may cause rx error.

This patch fixes it by using the last BD of the current packet in
hns3_handle_bdinfo.

Also, hns3_set_rx_skb_rss_type has used RSS hash value from the last
BD of the current packet, so remove the same last BD calculation in
hns3_set_rx_skb_rss_type and call it from hns3_handle_bdinfo.

Fixes: e5597095 ("net: hns3: Add handling of GRO Pkts not fully RX'ed in NAPI poll")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

hns3_desc_unused() returns how many BD have been cleaned, but new
buffer has not been attached to them. The register of
HNS3_RING_RX_RING_FBDNUM_REG returns how many BD need allocating new
buffer to or need to cleaned. So the remaining BD need to be clean
is HNS3_RING_RX_RING_FBDNUM_REG - hns3_desc_unused().

Also, new buffer can not attach to the pending BD when the last BD is
not handled, because memcpy has not been done on the first pending BD.

This patch fixes by subtracting the pending BD num from unused_count
after 'HNS3_RING_RX_RING_FBDNUM_REG - unused_count' is used to calculate
the BD bum need to be clean.

Fixes: e5597095 ("net: hns3: Add handling of GRO Pkts not fully RX'ed in NAPI poll")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

hns3_clean_tx_ring calls hns3_nic_reclaim_one_desc to clean
buffers and set ring->next_to_clean, then hns3_nic_net_xmit
reuses the cleaned buffers. But there are no memory barriers
when buffers gets recycled, so the recycled buffers can be
corrupted.

This patch uses smp_store_release to update ring->next_to_clean
and smp_load_acquire to read ring->next_to_clean to properly
hand off buffers from hns3_clean_tx_ring to hns3_nic_net_xmit.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Device may be shutdown without the hardware being reinitialized, in
which case we want to ensure we cleanup properly.

This is especially important for kexec with traffic flowing.

The shutdown procedures resembles the remove procedures, so we can reuse
those common tasks.
Signed-off-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/nfc/st95hf/core.c: In function 'st95hf_irq_thread_handler':
drivers/nfc/st95hf/core.c:786:26: warning:
 variable 'nfcddev' set but not used [-Wunused-but-set-variable]

drivers/nfc/st95hf/core.c:784:17: warning:
 variable 'dev' set but not used [-Wunused-but-set-variable]

They are never used since introduction in
commit cab47333 ("NFC: Add STMicroelectronics ST95HF driver")
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PHY's behave differently when being reset. Some reset registers to
defaults, some don't. Some trigger an autoneg restart, some don't.

So let's also set the autoneg restart bit when resetting. Then PHY
behavior should be more consistent. Clearing BMCR_ISOLATE serves the
same purpose and is borrowed from genphy_restart_aneg.

BMCR holds the speed / duplex settings in fixed mode. Therefore
we may have an issue if a soft reset resets BMCR to its default.
So better call genphy_setup_forced() afterwards in fixed mode.
We've seen no related complaint in the last >10 yrs, so let's
treat it as an improvement.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All Apple products use the same protocol for tethering over USB.
To simplify the code and make it future proof, use
USB_VENDOR_AND_INTERFACE_INFO() instead of
USB_DEVICE_AND_INTERFACE_INFO() to automatically detect and support
all existing and future Apple products using the same interface.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, refactor code a
bit and mark switch cases where we are expecting to fall through.

This patch fixes the following warning:

drivers/net/ethernet/broadcom/cnic.c: In function ‘cnic_cm_process_kcqe’:
drivers/net/ethernet/broadcom/cnic.c:4044:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
    opcode = L4_KCQE_OPCODE_VALUE_CLOSE_COMP;
drivers/net/ethernet/broadcom/cnic.c:4050:2: note: here
  case L4_KCQE_OPCODE_VALUE_RESET_RECEIVED:
  ^~~~

Warning level 3 was used: -Wimplicit-fallthrough=3

Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.

This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.

This patch fixes the following warning:

drivers/net/ethernet/chelsio/cxgb4vf/cxgb4vf_main.c: In function ‘fwevtq_handler’:
drivers/net/ethernet/chelsio/cxgb4vf/cxgb4vf_main.c:520:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
   cpl = (void *)p;
   ~~~~^~~~~~~~~~~
drivers/net/ethernet/chelsio/cxgb4vf/cxgb4vf_main.c:524:2: note: here
  case CPL_SGE_EGR_UPDATE: {
  ^~~~

Warning level 3 was used: -Wimplicit-fallthrough=3

Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.

This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.

This patch fixes the following warning:

In file included from drivers/net/wimax/i2400m/debug-levels.h:30,
                 from drivers/net/wimax/i2400m/control.c:86:
drivers/net/wimax/i2400m/control.c: In function ‘i2400m_report_tlv_system_state’:
./include/linux/wimax/debug.h:200:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
 do {         \
    ^
./include/linux/wimax/debug.h:404:36: note: in expansion of macro ‘_d_printf’
 #define d_printf(l, _dev, f, a...) _d_printf(l, "", _dev, f, ## a)
                                    ^~~~~~~~~
drivers/net/wimax/i2400m/control.c:354:3: note: in expansion of macro ‘d_printf’
   d_printf(1, dev, "entering BS-negotiated idle mode\n");
   ^~~~~~~~
drivers/net/wimax/i2400m/control.c:355:2: note: here
  case I2400M_SS_DISCONNECTING:
  ^~~~

Warning level 3 was used: -Wimplicit-fallthrough=3

This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.

This patch fixes the following warnings:

In file included from drivers/net/ethernet/amd/xgbe/xgbe-drv.c:129:
drivers/net/ethernet/amd/xgbe/xgbe-drv.c: In function ‘xgbe_set_hwtstamp_settings’:
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1392:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
  (_var) |= (((_val) & ((0x1 << (_width)) - 1)) << (_index)); \
  ~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1419:2: note: in expansion of macro ‘SET_BITS’
  SET_BITS((_var),      \
  ^~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1614:3: note: in expansion of macro ‘XGMAC_SET_BITS’
   XGMAC_SET_BITS(mac_tscr, MAC_TSCR, TSVER2ENA, 1);
   ^~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1616:2: note: here
  case HWTSTAMP_FILTER_PTP_V1_L4_EVENT:
  ^~~~
In file included from drivers/net/ethernet/amd/xgbe/xgbe-drv.c:129:
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1392:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
  (_var) |= (((_val) & ((0x1 << (_width)) - 1)) << (_index)); \
  ~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1419:2: note: in expansion of macro ‘SET_BITS’
  SET_BITS((_var),      \
  ^~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1625:3: note: in expansion of macro ‘XGMAC_SET_BITS’
   XGMAC_SET_BITS(mac_tscr, MAC_TSCR, TSVER2ENA, 1);
   ^~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1627:2: note: here
  case HWTSTAMP_FILTER_PTP_V1_L4_SYNC:
  ^~~~
In file included from drivers/net/ethernet/amd/xgbe/xgbe-drv.c:129:
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1392:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
  (_var) |= (((_val) & ((0x1 << (_width)) - 1)) << (_index)); \
  ~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1419:2: note: in expansion of macro ‘SET_BITS’
  SET_BITS((_var),      \
  ^~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1636:3: note: in expansion of macro ‘XGMAC_SET_BITS’
   XGMAC_SET_BITS(mac_tscr, MAC_TSCR, TSVER2ENA, 1);
   ^~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1638:2: note: here
  case HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ:
  ^~~~

Warning level 3 was used: -Wimplicit-fallthrough=3

Notice that, in this particular case, the code comments are modified
in accordance with what GCC is expecting to find.

This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When building the L3 HW header for non-IP packets, trust the cast type
that was passed as parameter. qeth_l3_get_cast_type() has most likely
also used h_dest to determine the cast type, so we get the same
result, and can remove that duplicated code.
In the unlikely case that we would get a _different_ cast type, then
that's based off a route lookup and should be considered authoritative.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This de-duplicates the L2 and L3 cast-type code, and makes the L2 code
a bit more robust by removing the fragile assumption that skb->data
always points to the Ethernet Header. This would break in code paths
where we pushed the HW header onto the skb.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The QETH_MAX_BUFFER_ELEMENTS() macro effectively returns a constant
value. To avoid some redundant pointer chasing and computations in the
xmit hot path, cache this value in the queue struct.

Take this as opportunity to shrink some of the queue struct's fields to
their appropriate value range, slightly reducing its total size.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On the first initialization of a queue, its Output Buffers are in a
clean state with no attached resources. On every subsequent
initialization, qeth_l?_stop_card() has previously put them in a clean
state via qeth_drain_output_queues(). So the call to
qeth_clear_output_buffer() is redundant and can be removed.

While at it, move the initialization of the queue's card pointer into
the queue allocation. It never changes afterwards.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>