When mwifiex device becomes GO, unicast traffic between client1 and GO stops
when client2 connects to GO. Reason behind this was PTK getting
overwritten by key_material command for client2 as it did not have client
mac address. So, client1 can no more decode GO's ping packets though it
responds to its broadcast packets.

This patch adds case to check for BSS_ROLE instead of bss_type to set
client mac address while configuring keys when device becomes GO.
Signed-off-by: NMaithili Hinge <maithili@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On AR9003, tx control and tx status are in separate descriptor rings.
Tx duration is extracted from the tx control descriptor data, which
ar9003_hw_proc_txdesc cannot access.

Fix getting the duration by adding a separate callback for it.
Acked-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

chan_lock is not required for checking if
we are in the middle of a HW reset, so do it
early. This also removes the small window
where the lock is dropped and reacquired.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add basic wowl (magic packet and disconnect) support. This patch adds
this support only for PCIE bus devices. This feature requires FW which
has support for wowl built in.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When driver gets unloaded due to error situation there is a chance
a packet gets received while fws has already been cleaned up. This
will result in kernel crash. This patch adds a check to avoid this
crash.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In order to provision the P2P_DEVICE mac address using p2p_da_override iovar
the discovery interface must be disabled. On some targets setting the mac
address failed so disable the discovery interface to be certain.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Msgbuf is using GFP_ATOMIC where GFP_KERNEL is also sufficient. On
some platforms the coherent DMA memory is very limited when using
GFP_ATOMIC. This patch changes usage of GFP_ATOMIC to GFP_KERNEL and
uses worker to make this possible for creation of flowring.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Need a cast to assure correct value is propagated.
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Increase driver scan timeout from 8 to 10 seconds and report results
to cfg80211. Without this patch the already received results were
dropped on driver timeout.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On AR934x and newer SoC devices, the layout of the AR_RTC_PLL_CONTROL
register changed. This currently breaks at least 5/10 MHz operation.
AR933x uses the old layout.

It might also have been causing other stability issues because of the
different location of the PLL_BYPASS bit which needs to be set during
PLL clock initialization.

This patch also removes more instances of hardcoded register values in
favor of properly computed ones with the PLL_BYPASS bit added.
Reported-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The cycpwr_thr1 value needs to be lower on the extension channel than on
the control channel, similar to how the register settings are programmed
in the initvals.

Also drop the unnecessary check for HT40 - this register can always be
written. This patch has been reported to improve HT40 stability and
throughput in some environments.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit 09efc563

I've received reports that this change is decreasing throughput in some
rare conditions on an AR9280 based device

Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

SKB lists have their own lock. So this lock is not needed.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes an issue with rx processing function where we were
decrementing rx_pending count twice.

Patch also queues correct main_work item when rx_pending count reaches
low watermark.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A soft lockup was observed on ARM multicore platform while UDP
RX iperf was running on station.

Reason for this is delay_main_task was not taken into consideration while
jumping to process_start. Now if delay_main_task is true, we would exit
mwifiex_main_process instead of going to process_start again.
This ensure other process is scheduled on this CPU and soft lockup is avoided.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKevin Gan <ganhy@marvell.com>
Signed-off-by: NMarc Yang <yangyang@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After short chat with Ivo, we decided that I'll take maintenance
of rt2x00 driver.

Thanks for Ivo's great work in the past!
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NIvo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On AR934x rev 3, settin the ad-hoc flag completely messes up hardware
state - beacons get stuck, almost no packets make it out, hardware is
constantly reset.

When leaving out that flag and setting up the hw like in AP mode, TSF
timers won't be automatically synced, but at least the rest works.

AR934x rev 2 and older are not affected by this bug
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is needed for AR934x as well
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Needed for calling vmalloc()/vfree()
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In a number of places, kmalloc or valloc were used to acquire memory.
To ensure that these locations are correctly initialized, the calls were
changed to kzalloc and vzalloc. The change fixes a problem that was causing
HT operations to be cancelled.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8188ee: rtl8192com: rtl8192cu: rtl8192ee: rtl8723ae: rtl87323be: rtl8821ae: Use common cmd_send_packet

A locking problem was found in routine _rtl92ee_cmd_send_packet() that led
to system freezes. Upon inspection, several drivers had the same problem;
however, the routines all used the same code. The common code has been
moved into rtlwifi.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Realtek released new drivers on 06/28/2014. These changes implement all their
changes into the kernel version of the driver. In addition, these modifications
are part of the process of unifying the Realtek and kernel code bases.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch updates the driver to match the latest Realtek release, and
it is an important step in getting the internal code source at Realtek to match
the code in the kernel. The primary reason for this is to make it easier for
Realtek to maintain the kernel source without requiring an intermediate like me.

In this process of merging the two source repositories, there are a lot
of changes in both, and this commit is rather large.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Not only does this patch update the driver to match the latest Realtek release,
it is an important step in getting the internal code source at Realtek to match
the code in the kernel. The primary reason for this is to make it easier for
Realtek to maintain the kernel source without requiring an intermediate like me.

In this process of merging the two source repositories, there are a lot
of changes in both, and this commit is rather large.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This driver was entered into staging a few cycles ago because there was
not time to integrate the Realtek version into the support routines in
the kernel. Now that there is an effort to converg the code base from Linux
and the Realtek repo, it is time to move this driver. In addition, all the
updates included in the 06/28/2014 version of the Realtek drivers are
included here.

With this change, it will be necessary to delete the staging driver. That
will be handled in a separate patch. As it impacts the staging tree, such a
patch is sent to a different destination.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The code fails to lock the skb queue, which leads to a number of problems.
This patch also fixes a Sparse warning about using a memset of 1 byte.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: troy_tan@realsil.com.cn
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This will allow us to define GPIO-attached devices (LEDs, buttons) in
the the device tree.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This driver is used by the bcm53xx ARM SoC code. Now it is possible to
give the address of the chipcommon core in device tree and bcma will
search for all the other cores.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We will now dump MAC, APU, CIU, ICU firmware memory segments also
for PCIe interface. Following is the updated userspace script which
reads firmware dump information.

    mwifiex_pcie_fw_dump.sh: #!/bin/bash
    ethtool --set-dump mlan0 0
    ethtool --get-dump mlan0
    ethtool --get-dump mlan0 data /tmp/ITCM.log

    ethtool --set-dump mlan0 1
    ethtool --get-dump mlan0
    ethtool --get-dump mlan0 data /tmp/DTCM.log

    ethtool --set-dump mlan0 2
    ethtool --get-dump mlan0
    ethtool --get-dump mlan0 data /tmp/SQRAM.log

    ethtool --set-dump mlan0 3
    ethtool --get-dump mlan0
    ethtool --get-dump mlan0 data /tmp/IRAM.log

    ethtool --set-dump mlan0 4
    ethtool --get-dump mlan0
    ethtool --get-dump mlan0 data /tmp/APU.log

    ethtool --set-dump mlan0 5
    ethtool --get-dump mlan0
    ethtool --get-dump mlan0 data /tmp/CIU.log

    ethtool --set-dump mlan0 6
    ethtool --get-dump mlan0
    ethtool --get-dump mlan0 data /tmp/ICU.log

    ethtool --set-dump mlan0 7
    ethtool --get-dump mlan0
    ethtool --get-dump mlan0 data /tmp/MAC.log
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch takes care of missing error paths in firmware dump.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This driver was entered into staging a few cycles ago because there was
not time to integrate the Realtek version into the support routines in
the kernel. Now that there is an effort to converg the code base from Linux
and the Realtek repo, it is time to move this driver. In addition, all the
updates included in the 06/28/2014 version of the Realtek drivers are
included here.

With this change, it will be necessary to delete the staging driver. That
will be handled in a separate patch. As it impacts the staging tree, such a
patch is sent to a different destination.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Not only does this patch update the driver to match the latest Realtek release,
it is an important step in getting the internal code source at Realtek to match
the code in the kernel. The primary reason for this is to make it easier for
Realtek to maintain the kernel source without requiring an intermediate like me.

In this process of merging the two source repositories, there are a lot
of changes in both, and this commit is rather large.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Addition of the new drivers and the update to a new version for the others
lead to changes in all the core routines.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Realtek released a new version of the drivers on 06/28/2014. This
patch implements the new power-save code. These changes also force
corresponding changes in the drivers.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Each of the routines in the rtlwifi common driver needs to be modified
for the coming changes. This patch prepares core.c, but also touches other
files.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Future patches will move the drivers for RTL8192EE and RTL8821AE
from staging to the regular wireless tree. Here, the necessary features
are added to the PCI driver. Other files are touched due to changes
in the various data structs.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the rtlwifi family of drivers was converted to use a workqueue when
entering or leaving power save mode (commits a269913c, a5ffbe0a,
41affd52, b9116b9a, and 6539306b), the code began scheduling work from
the callback routine of a different workqueue with a resulting increase in
overhead.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>