When operating at 1GbE, the base incval for the PTP clock is so large
that multiplying it by numbers close to the max_adj can overflow the
u64.

Rather than attempting to limit the max_adj to a value small enough to
avoid overflow, instead calculate the incvalue adjustment based on the
40GbE incvalue, and then multiply that by the scaling factor for the
link speed.

This sacrifices a small amount of precision in the adjustment but we
avoid erratic behavior of the clock due to the overflow caused if ppb is
very near the maximum adjustment.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This fixes at least 2 issues I have found with the UDP tunnel filter
configuration.

The first issue is the fact that the tunnels didn't have any sort of mutual
exclusion in place to prevent an update from racing with a user request to
add/remove a port. As such you could request to add and remove a port
before the port update code had a chance to respond which would result in a
very confusing result. To address it I have added 2 changes. First I added
the RTNL mutex wrapper around our updating of the pending, port, and
filter_index bits. Second I added logic so that we cannot use a port that
has a pending deletion since we need to free the space in hardware before
we can allow software to reuse it.

The second issue addressed is the fact that we were not recording the
actual filter index provided to us by the admin queue. As a result we were
deleting filters that were not associated with the actual filter we wanted
to delete. To fix that I added a filter_index member to the UDP port
tracking structure.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes the problem where each MTU change turns TSO,
GSO and GRO on from off state.

Now when TSO, GSO or GRO is turned off, MTU change does not
turn them on.
Signed-off-by: NPaweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The advertising 10G LR mode should be possible to set
but in the function i40e_set_link_ksettings() check for this
is missed. This patch adds check for 10000baseLR_Full
flag for 10G modes.
Signed-off-by: NJakub Pawlak <jakub.pawlak@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Previous method for reading LLDP config was based on hard-coded
offsets. It happened to work, because of structured architecture of
the NVM memory. In the new approach, known as FLAT, we need to
calculate the absolute address, instead of using relative values.
Needed defines for memory location were added.
Signed-off-by: NMariusz Stachura <mariusz.stachura@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Recent versions of the Linux kernel now warn about incorrect parameter
definitions for function comments. Fix up several function comments to
correctly reflect the current function arguments. This cleans up the
warnings and helps ensure our documentation is accurate.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

i40evf_add_vlan() is never called in atomic context.

i40evf_add_vlan() is only called by i40evf_vlan_rx_add_vid(),
which is only set as ".ndo_vlan_rx_add_vid" in struct net_device_ops.
".ndo_vlan_rx_add_vid" is not called in atomic context.

Despite never getting called from atomic context,
i40evf_add_vlan() calls kzalloc() with GFP_ATOMIC,
which does not sleep for allocation.
GFP_ATOMIC is not necessary and can be replaced with GFP_KERNEL,
which can sleep and improve the possibility of sucessful allocation.

This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: NJia-Ju Bai <baijiaju1990@gmail.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Trivial fix to spelling mistake in oct_stats_strings text
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enhancing driver to accept max supported queues for ethtool --set-channels
Signed-off-by: NIntiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: NDerek Chickles <derek.chickles@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moved common function setup_glists to lio_core.c
and reamed it to lio_setup_glists
Signed-off-by: NIntiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: NDerek Chickles <derek.chickles@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moving common definition octnic_gather to octeon_network.h
Signed-off-by: NIntiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: NDerek Chickles <derek.chickles@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moved common function delete_glists to lio_core.c
and renamed it to lio_delete_glists
Signed-off-by: NIntiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: NDerek Chickles <derek.chickles@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moved common function list_delete_head to octeon_network.h
and renamed it to lio_list_delete_head
Signed-off-by: NIntiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: NDerek Chickles <derek.chickles@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moved common function if_cfg_callback to lio_core.c
and renamed it to lio_if_cfg_callback.
Signed-off-by: NIntiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: NDerek Chickles <derek.chickles@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code in the fallback path has supported XDP in conjunction with the Tx
traffic classification for TCs for over a year now. So instead of just
calling skb_tx_hash for every packet we are better off using the fallback
since that will record the Tx queue to the socket and then that can be used
instead of having to recompute the hash every time.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add logic to reserve default rings at driver open time if none was
reserved during probe time.  This will happen when the PF driver did
not provision minimum rings to the VF, due to more limited resources.

Driver open will only succeed if some minimum rings can be reserved.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For completeness and correctness, the VF driver needs to reserve these
RSS and L2 contexts.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When rings are more limited and the PF has not provisioned minimum
guaranteed rings to the VF, do not reserve rings during driver probe.
Wait till device open before reserving rings when they will be used.
Device open will succeed if some minimum rings can be successfully
reserved and allocated.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current code does not reserve rings during ethtool -L when the device
is down.  The rings will be reserved when the device is later opened.

Change it to reserve rings during ethtool -L when the device is down.
This provides a better guarantee that the device open will be successful
when the rings are reserved ahead of time.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds debugfs support for bnxt_en with the purpose of allowing users
to examine the current DIM profile in use for each receive queue.  This
was instrumental in debugging issues found with DIM and ensuring that
the profiles we expect to use are the profiles being used.
Signed-off-by: NAndy Gospodarek <gospo@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Testing with DIM enabled on older kernels indicated that firmware calls
were slower than expected.  More detailed analysis indicated that the
default 25us delay was higher than necessary.  Reducing the time spend in
usleep_range() for the first several calls would reduce the overall
latency of firmware calls on newer Intel processors.
Signed-off-by: NAndy Gospodarek <gospo@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This keeps the RING_IDLE flag set in hardware for higher coalesce
settings by default and improved latency.
Signed-off-by: NAndy Gospodarek <gospo@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Firmware does not allow the operation and would return failure, causing
a warning in dmesg.  So check for VF and disallow it in the driver.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add counters to display sum of rx/tx_discard_pkts of all rings as
function level statistics via ethtool.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace switch statements printing different messages for every ring type
with a common message.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Older firmware will reject this call and cause an error message to
be printed by the VF driver.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Firmware messages that are forwarded from PF to VFs are encapsulated.
The size of these encapsulated messages must not exceed the maximum
defined message size.  Add appropriate checks to avoid oversize
messages.  Firmware messages may be expanded in future specs and
this will provide some guardrails to avoid data corruption.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initially, the MQPRIO TCs are mapped 1:1 directly to the hardware
queues.  Some of these hardware queues are configured to be lossless.
When PFC is enabled on one of more TCs, we now need to remap the
TCs that have PFC enabled to the lossless hardware queues.

After remapping, we need to close and open the NIC for the new
mapping to take effect.  We also need to reprogram all ETS parameters.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current driver maps MQPRIO traffic classes directly 1:1 to the
internal hardware queues (TC0 maps to hardware queue 0, etc).  This
direct mapping requires the internal hardware queues to be reconfigured
from lossless to lossy and vice versa when necessary.  This
involves reconfiguring internal buffer thresholds which is
disruptive and not always reliable.

Implement a new scheme to map TCs to internal hardware queues by
matching up their PFC requirements.  This will eliminate the need
to reconfigure a hardware queue internal buffers at run time.  After
remapping, the NIC is closed and opened for the new TC to hardware
queues to take effect.

This patch only adds the basic mapping logic.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After many years of having a ~30 line copyright and license header to our
source files, we are finally able to reduce that to one line with the
advent of the SPDX identifier.

Also caught a few files missing the SPDX license identifier, so fixed
them up.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@oracle.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support ndo_get_stats64 instead of ndo_get_stats.  Also add stats for
multicast and broadcast packets.
Signed-off-by: NPradeep Nalla <pradeep.nalla@cavium.com>
Acked-by: NRaghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To support the next patch in this series which has code that calls
octnet_get_link_stats from two different .c files, move that function (and
its dependency octnet_nic_stats_callback) to lio_core.c.  Remove
octnet_get_link_stats's static declaration and add its function prototype
in octeon_network.h.
Signed-off-by: NPradeep Nalla <pradeep.nalla@cavium.com>
Acked-by: NRaghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are two identical nested if statements, the second is redundant
and can be removed. Also clean up white space formatting.

Cleans up cppcheck warning:
drivers/net/ethernet/amd/amd8111e.c:1080: (warning) Identical inner 'if'
condition is always true.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This allows filters added by tc-flower and specifying MAC addresses,
Ethernet types, and the VLAN priority field, to be offloaded to the
controller.

This reuses most of the infrastructure used by ethtool, but clsflower
filters are kept in a separated list, so they are invisible to
ethtool.

To setup clsflower offloading:

$ tc qdisc replace dev eth0 handle 100: parent root mqprio \
     	   	   num_tc 3 map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 \
		   queues 1@0 1@1 2@2 hw 0
(clsflower offloading depends on the netword driver to be configured
with multiple traffic classes, we use mqprio's 'num_tc' parameter to
set it to 3)

$ tc qdisc add dev eth0 ingress

Examples of filters:

$ tc filter add dev eth0 parent ffff: flower \
     	    dst_mac aa:aa:aa:aa:aa:aa \
	    hw_tc 2 skip_sw
(just a simple filter filtering for the destination MAC address and
steering that traffic to queue 2)

$ tc filter add dev enp2s0 parent ffff: proto 0x22f0 flower \
     	    src_mac cc:cc:cc:cc:cc:cc \
	    hw_tc 1 skip_sw
(as the i210 doesn't support steering traffic based on the source
address alone, we need to use another steering traffic, in this case
we are using the ethernet type (0x22f0) to steer traffic to queue 1)
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If a flower rule has a repr both as ingress and egress port then 2
callbacks may be generated for the same rule request.

Add an indicator to each flow as to whether or not it was added from an
ingress registered cb. If so then ignore add/del/stat requests to it from
an egress cb.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When multiple netdevs are attached to a tc offload block and register for
callbacks, a rule added to the block will be propogated to all netdevs.
Previously these were detected as duplicates (based on cookie) and
rejected. Modify the rule nfp lookup function to optionally include an
ingress netdev and a host context along with the cookie value when
searching for a rule. When a new rule is passed to the driver, the netdev
the rule is to be attached to is considered when searching for dublicates.
When a stats update is received from HW, the host context is used
alongside the cookie to map to the correct host rule.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To aid debugging of performance issues caused by limited PCIe
bandwidth print the PCIe link information on probe.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NFP locks record the owner when held, for PCIe devices the owner
ID will be the PCIe link number.  When driver loads it should scan
known locks and if they indicate that they are held by local
endpoint but the driver doesn't hold them - release them.

Locks can be left taken for instance when kernel gets kexec-ed or
after a crash.  Management FW tries to clean up stale locks too,
but it currently depends on PCIe link going down which doesn't
always happen.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds basic functions needed to implement offloading for filters
created by tc-flower.
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This adds the capability of configuring the queue steering of arriving
packets based on their source and destination MAC addresses.

Source address steering (i.e. driving traffic to a specific queue),
for the i210, does not work, but filtering does (i.e. accepting
traffic based on the source address). So, trying to add a filter
specifying only a source address will be an error.

In practical terms this adds support for the following use cases,
characterized by these examples:

$ ethtool -N eth0 flow-type ether dst aa:aa:aa:aa:aa:aa action 0
(this will direct packets with destination address "aa:aa:aa:aa:aa:aa"
to the RX queue 0)

$ ethtool -N eth0 flow-type ether src 44:44:44:44:44:44 \
  	     	  	    	  proto 0x22f0 action 3
(this will direct packets with source address "44:44:44:44:44:44" and
ethertype 0x22f0 to the RX queue 3)
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>