[Why]
If the system does not have hostvm enabled, disabling it for
DML validation will allow more modes to pass at lower voltage
levels.

[How]
When initializing HostVM save state to hubbub and read back
when populating DML pipes from context.
Signed-off-by: NSung Lee <sung.lee@amd.com>
Acked-by: NBindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why & How]
Program modulo with ref dpp clk Mhz/10.
Program phase with pipe dpp clk Mhz /10.
DMUB FW could use these value to determine optimization clk
for PSR power saving.
Signed-off-by: NYongqiang Sun <yongqiang.sun@amd.com>
Acked-by: NBindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
When mpo enabled, video comes is 709. Desktop use sRGB.
So color change easily noticeable especially when switch between
mpo/non-mpo.

[How]
Force use sRGB for video TF is sRGB or BT709.
DCN1/DCN2 use predefined type with YUV.
DCN3 use distributed points type with YUV.
Signed-off-by: NJing Zhou <Jing.Zhou@amd.com>
Acked-by: NBindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Due to the freesync power optimization increasing vtotal, the driver
believes that MPO is supported. MPO is turned on. Freesync then
exits, MPO can no longer be supported and immediate flip fails. This
causes corruption on the panel.

[How]
Avoid the freesync optimization when doing validation so in the case
freesync exits, driver can still support the configuration.
Signed-off-by: NIsabel Zhang <isabel.zhang@amd.com>
Acked-by: NBindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
In some cases, prefetch mode 0 is unsupported but prefetch 1 is
supported. Due to previous change always forcing prefetch mode to 0, we
are failing bandwidth validation in cases where we should not.

[How]
By default try prefetch mode 0 but in the case validation fails, attempt
to do prefetch mode 1 to see if it is supported.
Signed-off-by: NIsabel Zhang <isabel.zhang@amd.com>
Acked-by: NBindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
On APU should be always using prefetch mode 0.
Currently, sometimes prefetch mode 1 is being
used causing system to hard hang due to
minTTUVBlank being too low.

[How]
Any ASIC running DCN21 will by default allow
self refresh and mclk switch. This sets both
min and max prefetch mode to 0 by default.
Signed-off-by: NIsabel Zhang <isabel.zhang@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Some sink devices wish to have access to the minimum
HBlank supported by the ASIC.

[How]
Make the ASIC minimum HBlank available in Source
Device information address 0x340.
Signed-off-by: NAshley Thomas <Ashley.Thomas2@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY & HOW]
Enable ODM Combine + Fullscreen MPO on DCN2.1
For lower power consumption in video use cases.
Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: NSung Lee <sung.lee@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why&How]
Create a separate dcn21_fast_validate_bw function for dcn21.
Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
DF PState and Voltage State are coupled such that one cannot be
raised without raising the other. This uses more power than
is necessary in high bandwidth scenarios.

[HOW]
Add logic to create a new bounding box state that allows for
DF PState to be low while Voltage State is high. Watermarks
vlevel calculation logic was also udpated to assume
state 1 contains the new optimized state.
Signed-off-by: NSung Lee <sung.lee@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
Currently construction of clock limits gets skipped for diags.
This logic would be useful to get tested in diags.

[HOW]
Copy existing states to clk_table such that update_bw_bounding_box
logic gets used to fill the table.
Signed-off-by: NSung Lee <sung.lee@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NEryk Brol <eryk.brol@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
HDCP 1.4 failed on SL8800 SW w/a test driver use.

[how]
Slow down the HW i2c speed when used by HW i2c.
This request: each acquired_i2c_engine setup the i2c speed needed
and sets the I2c engine for HDCP use at release_engine.

This covers SW using HW i2c engine and HDCP using HW i2c engine.
for dmcu using HW i2c engine, needs add similar logic in dmcu fw.
Signed-off-by: NCharlene Liu <Charlene.Liu@amd.com>
Reviewed-by: NChris Park <Chris.Park@amd.com>
Acked-by: NEryk Brol <eryk.brol@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Disable triplebuffering by default.
Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Current pipe merge and split logic only supports cases where new
dc_state is allocated and relies on dc->current_state to gather
information from previous dc_state.

Calls to validate_bandwidth on UPDATE_TYPE_MED would cause an issue
because there is no new dc_state allocated, and data in
dc->current_state would be overwritten during pipe merge.

[how]
Only allow validate_bandwidth when new dc_state space is created.
Signed-off-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The only usage of dcn21_res_pool_funcs is to assign its address to a
const pointer. Make it const to allow the compiler to put it in
read-only memory.
Signed-off-by: NRikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Implement an interface to obtain plane size caps

[How]
Add min_width, min_height fields to dc_plane_cap structure.
Set values to 16x16 for discrete ASICs, and 64x64 for others.
Signed-off-by: NIgor Kravchenko <Igor.Kravchenko@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
dcn20_add_dsc_to_stream_resource is accessed in amdgpu_dm directly.
This creates build error for configuration with DCN disabled.

[How]
Make the function available through a resource pool function so
that dcn20 function need not be called directly.
Signed-off-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
DP link layer CTS specs updated to change the test parameters in test
4.2.1.1.
Before it requires source to delay 400us on aux no reply.
With the specs updates Errata5, it requires source to delay 3.2ms
(based on LTTPR aux timeout)
This causes our test to fail after updating with the latest test
equipment firmware.

[how]
the change is to allow LTTPR 3.2ms aux timeout delay by default.
And set back to 400us if LTTPR feature is not enabled.
We will set 3.2ms and always enable LTTPR non transparent mode
if LTTPR feature is enabled and LTTPR is present.
Signed-off-by: NWenjing Liu <wenjing.liu@amd.com>
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NKrunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why & How]
DMUB command table should be allowed to be used
only if dmcu is explicitly disabled.
Signed-off-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
The change causes some regression in a common use case.
Will need more investigation before fixing the original issue.

[how]
This reverts commit fb8cf277.
Signed-off-by: NWenjing Liu <wenjing.liu@amd.com>
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
SOC_BOUNDING_BOX_VALID is unused and not required for dcn21.

[How]
Remove it.
Signed-off-by: NRoman Li <Roman.Li@amd.com>
Reviewed-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
dal side nv12 wa has a lot of side effects.
KMD side wa is used, so this should be remove.

[How]
Removed wa from dal side.
Signed-off-by: NYongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Save the correct num vmid during resource creation and fix RN gpuvm
level from 1 to 16 vmid entries.
Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: NEric Bernstein <Eric.Bernstein@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Fixes coccicheck warning:

drivers/gpu/drm/amd/display/dc/dcn21/dcn21_resource.c:1398:60-61:
WARNING: Unsigned expression compared with zero: j >= 0

Fixes: 23838777 ("drm/amd/display: fix rn soc bb update")
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NZou Wei <zou_wei@huawei.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Current locking scheme for cursor can result in a flip missing
its vsync, deferring it for one or more vsyncs.  Result is a
potential for stuttering when cursor is moved.

[How]
Use cursor update lock so that flips are not blocked while cursor
is being programmed.
Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
The downspread percentage was copied over from a previous version
of the display_mode_lib spreadsheet. This value has been updated,
and the previous value is too high to allow for such modes as
4K120hz. The new value is sufficient for such modes.

[HOW]
Update the value in dcn21_resource to match the spreadsheet.
Signed-off-by: NSung Lee <sung.lee@amd.com>
Reviewed-by: NYongqiang Sun <yongqiang.sun@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Currently RN SOC bounding box update assumes we will get at least
2 clock states from SMU. This isn't always true and because of special
casing on first clock state we end up with low disp, dpp, dsc and phy
clocks.

This change removes the special casing allowing the first state to
acquire correct clocks.
Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: NEric Yang <eric.yang2@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: NTony Cheng <Tony.Cheng@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Current locking scheme for cursor can result in a flip missing
its vsync, deferring it for one or more vsyncs.  Result is a
potential for stuttering when cursor is moved.

[How]
Use cursor update lock so that flips are not blocked while cursor
is being programmed.
Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why&How]
modules/color calculates various colour operations which are translated
to abstracted HW. DCE 5-12 had almost no important changes, but
starting with DCN1, every new generation comes with fairly major
differences in color pipeline.
We would hack it with some DCN checks, but a better approach is to
abstract color pipe capabilities so modules/DM can decide mapping to
HW block based on logical capabilities,
Signed-off-by: NKrunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
The downspread percentage was copied over from a previous version
of the display_mode_lib spreadsheet. This value has been updated,
and the previous value is too high to allow for such modes as
4K120hz. The new value is sufficient for such modes.

[HOW]
Update the value in dcn21_resource to match the spreadsheet.
Signed-off-by: NSung Lee <sung.lee@amd.com>
Reviewed-by: NYongqiang Sun <yongqiang.sun@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Currently RN SOC bounding box update assumes we will get at least
2 clock states from SMU. This isn't always true and because of special
casing on first clock state we end up with low disp, dpp, dsc and phy
clocks.

This change removes the special casing allowing the first state to
acquire correct clocks.
Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: NEric Yang <eric.yang2@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: NTony Cheng <Tony.Cheng@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
it doesn't represent panel specifically, it's more like the control
logic for the panel

[How]
change from panel to panel cntl to make it a bit more clear
Signed-off-by: NAnthony Koo <Anthony.Koo@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
panel power sequencer is currently just sitting in hwseq but it really
it tied to internal panels

[How]
make a new panel struct to contain power sequencer code
Signed-off-by: NAnthony Koo <Anthony.Koo@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]:
Renoir's pipe VM flags are not correctly updated if pipe strategy has
changed during some scenarios. It will result in watermarks mistakenly
calculation, thus underflow and garbage appear.

[How]:
Correctly update pipe VM flags to pipes which have been populated.
Signed-off-by: NDale Zhao <dale.zhao@amd.com>
Signed-off-by: NSung Lee <sung.lee@amd.com>
Reviewed-by: NYongqiang Sun <yongqiang.sun@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
When dmcub is the default we no longer wish to create the psr and dmcu
objects. Currently a dc debug flag is used to implement this, but these
flags aren't populated until after dcn21_resource_construct is called.
This means the dmcub objects will never be created. Therefore we must
use a dc config flag, which is populated before dc resource construct.

[How]
Add a dc config flag.
Signed-off-by: NWyatt Wood <wyatt.wood@amd.com>
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Moving ABM from DMCU to DMCUB.

[How]
Add ABM driver files and implementation.
Signed-off-by: NWyatt Wood <wyatt.wood@amd.com>
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
DML expects num_states to exclude the duplicate state.

[How]
Set num_states to correct value to prevent array off-by-one error.  Also
refactor max clock level code for diags.
Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: NGeorge Shen <george.shen@amd.com>
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
P010 pixel format is not declared as supported in DRM and DM.

[How]
Add P010 format to the support list presented to DRM and checked in DM
Signed-off-by: NStylon Wang <stylon.wang@amd.com>
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
We want to be able to enable/disable psr on dmcub and fallback to dmcu
when necessary.

[How]
Use dc config option to do so.
Signed-off-by: NWyatt Wood <wyatt.wood@amd.com>
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
The default value for disable_dmcu is true, even for asics that require
dmcu.

[How]
Set flag properly per asic.
Signed-off-by: NWyatt Wood <wyatt.wood@amd.com>
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>