Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Update copyright date, remove author address and add Roger Tseng.
Signed-off-by: NWei WANG <wei_wang@realsil.com.cn>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Set a bit to enable rts5227 and rts5249 to enter a deeper internal
power-saving mode in S3, and recover it after resuming.
Signed-off-by: NWei WANG <wei_wang@realsil.com.cn>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Clear hw_pfm_en to disable hardware PFM mode, to fix a bug that in some
situation registers in 0xFDxx domain can't be accessed.
Signed-off-by: NWei WANG <wei_wang@realsil.com.cn>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

These actions are individual for each reader model, so should be put in
extra_init_hw instead of rtsx_pci_init_hw.
Signed-off-by: NWei WANG <wei_wang@realsil.com.cn>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Some actions to clear power state should be handled in .shutdown
callback in rtsx_pci_driver. This patch adopts the following measures to
catch this goal:
1. Add a function rtsx_pci_power_off to abstract the common ops in
.shutdown and .suspend
2. Add pcr->ops->force_power_down to fulfill the individual action for
each reader model
Signed-off-by: NWei WANG <wei_wang@realsil.com.cn>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Normally OEMs will set vendor setting to the config space of Realtek
card reader in BIOS stage. This patch reads the setting at the first,
and configure the internal registers according to it, to improve card
reader's compatibility condition.
Signed-off-by: NWei WANG <wei_wang@realsil.com.cn>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The TWL6032 PMIC has different IRQ status bits meaning.
Hence, add interrupt mapping table for the twl6032.
Signed-off-by: NOleksandr Dmytryshyn <oleksandr.dmytryshyn@ti.com>
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NGraeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Create "struct twl6030_irq" and place all local variables inside it.
Also allocate twl6030_irq structure dynamically during initialization.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NGraeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Since the TWL6030 PMIC is used with OMAP4 SoCs only and OMAP4 legacy
boot is dropped there are no needs to allocate the range of IRQ
descriptors during system boot to support TWL6030 IRQs.

Hence, convert it to use linear irq_domain and move IRQ configuration in
.map()/.unmap() callbacks of irq_domain. So, IRQ mapping and descriptors
allocation will be performed dynamically basing on DT configuration.

The error message will be reported in case if unmapped IRQ is received by
TWL6030 (virq==0).
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NGraeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add a missed check for errors when TWL IRQs are masked
initially on probe and report an error in case of failure.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NGraeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

1) Removed request_irq() and replaced it with request_threaded_irq().

2) Removed generic_handle_irq() and replaced it with
handle_nested_irq().
  Handling of these interrupts is nested, as we are handling an
interrupt (for e.g rtc, mmc1) when we are still servicing TWL irq.

3) Removed I2C read-retry logic for the case when twl_i2c_read() is
failed inside IRQ handler - there is no sense to do that, so just report
an error and return.

4) Each nested IRQ is configured with corresponding parent_irq,
which need to be retriggered in case if nested IRQ is marked
as IRQS_PENDING.
Signed-off-by: NNaga Venkata Srikanth V <vnv.srikanth@samsung.com>
Signed-off-by: NOleg_Kosheliev <oleg.kosheliev@ti.com>
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NGraeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d063
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Include <linux/module.h> in order to fix the following errors.

drivers/mfd/pm8921-core.c:209:16: error: expected declaration specifiers or '...' before string constant
drivers/mfd/pm8921-core.c:210:20: error: expected declaration specifiers or '...' before string constant
drivers/mfd/pm8921-core.c:211:16: error: expected declaration specifiers or '...' before string constant
drivers/mfd/pm8921-core.c:212:14: error: expected declaration specifiers or '...' before string constant
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Some of Palmas resources like clock, SMPSs, LDOs etc can be controlled
by external pins ENABLE1, ENABLE2 or NSLEEP.

Add support to configure these resources to externally controlled.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch adds a regmap irqchip for DA9063 IRQs. It depends on

  git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap.git tags/regmap-irq-ack-mask
Signed-off-by: NKrystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This is MFD module providing access to registers and interrupts of DA906x
series PMIC. It is used by other functional modules, registered as MFD cells.
Driver uses regmap with paging to access extended register list. Register map
is divided into two pages, where the second page is used during initialisation.

This module provides support to following functional cells:
 - Regulators
 - RTC
 - HWMON
 - OnKey (power key misc input device)
 - Vibration (force-feedback input device)
 - Watchdog
 - LEDs
Signed-off-by: NKrystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch adds register definitions for the DA9063 PMIC. They will be used
by the following DA9063 mfd core driver and functional module drivers.
Signed-off-by: NKrystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

regmap: Support for acknowledging masked IRQs

Some devices need interrupts to be clear when they are masked otherwise
the interrupt is not deasserted by the mask being set - add support for
this to regmap-irq from Philipp Zabel.

The reg_cache variable should be updated with current
steps in the reg_se register. Then the mask should
apply and clear the register. Previously, the reg_cache
can be an old redundant value that isn't updated.
Signed-off-by: NZubair Lutfullah <zubair.lutfullah@gmail.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The child device intends to perform DMA operations then it needs a dma
mask and params set. This patches copies them from the parent device.
Signed-off-by: NBenedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: NHolger Dengler <dengler@linutronix.de>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

There is no need to use a per CPU workqueue to poll, especially with the
5s delay used, so allow the scheduler to use any CPU.
Signed-off-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch adds DMI system IDs for the new Kontron modules COMe-bHL6 and
COMe-cTH6 to the Kontron PLD driver.
Acked-by: NKevin Strasser <strassek@engr.orst.edu>
Signed-off-by: NMichael Brunner <michael.brunner@kontron.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Hook up "pm_power_off" to palmas power off routine if there is DT
property "ti,system-power-controller" defined, so platform which is
powered by this regulator can be powered off properly.
Acked-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NMallikarjun Kasoju <mkasoju@nvidia.com>
Signed-off-by: NBill Huang <bilhuang@nvidia.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch adds clock to list of mfd cells for s2mps11 and DT documentation
for clock part.
Reviewed-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NYadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

FX_CTRL2 is a volatile register and should be marked as such, this patch
does so.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The mic detect level registers are used from common code to configure
the button detection code. Add these registers to the defaults list and
mark them as readable for wm5110.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The FLL gains are present on all devices and controlled from common code
shared between them. This patch adds these registers into defaults list
for wm5110 and marks them as readable.
Reported-by: ND.J. Barrow <dbarrow@wolfsonmicro.com>
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Reg_cache variable is used to lock step enable register
from being accessed and written by both TSC and ADC
at the same time.
However, it isn't updated anywhere in the code at all.

If both TSC and ADC are used, eventually 1FFFF is always
written enabling all 16 steps uselessly causing a mess.

Patch fixes it by correcting the locks and updates the
variable by reading the step enable register
Signed-off-by: NZubair Lutfullah <zubair.lutfullah@gmail.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

If we disable DCVDD before we mark the cache as cache only, we might
attempt to write to the chip whilst it is powered down and lose a write.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add CONFIG_PM_SLEEP to suspend/resume functions to fix the build
warnings when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SET_SYSTEM_SLEEP_PM_OPS are only used
when the CONFIG_PM_SLEEP is enabled.

drivers/mfd/ab8500-gpadc.c:891:12: warning: 'ab8500_gpadc_suspend' defined but not used [-Wunused-function]
drivers/mfd/ab8500-gpadc.c:903:12: warning: 'ab8500_gpadc_resume' defined but not used [-Wunused-function]
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add CONFIG_PM_RUNTIME to runtime_suspend/runtime_resume functions
to fix the build warnings when CONFIG_PM_RUNTIME is not selected.
This is because runtime PM callbacks defined by SET_RUNTIME_PM_OPS
are only used when the CONFIG_PM_RUNTIME is enabled.

drivers/mfd/ab8500-gpadc.c:870:12: warning: 'ab8500_gpadc_runtime_suspend' defined but not used [-Wunused-function]
drivers/mfd/ab8500-gpadc.c:878:12: warning: 'ab8500_gpadc_runtime_resume' defined but not used [-Wunused-function]
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>