Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 31 1月, 2016 1 次提交
    • D
      block: revert runtime dax control of the raw block device · 9f4736fe
      由 Dan Williams 提交于 
      Dynamically enabling DAX requires that the page cache first be flushed
and invalidated.  This must occur atomically with the change of DAX mode
otherwise we confuse the fsync/msync tracking and violate data
durability guarantees.  Eliminate the possibilty of DAX-disabled to
DAX-enabled transitions for now and revisit this for the next cycle.

Cc: Jan Kara <jack@suse.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
      9f4736fe
  3. 23 1月, 2016 2 次提交
    • R
      dax: support dirty DAX entries in radix tree · f9fe48be
      由 Ross Zwisler 提交于 
      Add support for tracking dirty DAX entries in the struct address_space
radix tree.  This tree is already used for dirty page writeback, and it
already supports the use of exceptional (non struct page*) entries.

In order to properly track dirty DAX pages we will insert new
exceptional entries into the radix tree that represent dirty DAX PTE or
PMD pages.  These exceptional entries will also contain the writeback
addresses for the PTE or PMD faults that we can use at fsync/msync time.

There are currently two types of exceptional entries (shmem and shadow)
that can be placed into the radix tree, and this adds a third.  We rely
on the fact that only one type of exceptional entry can be found in a
given radix tree based on its usage.  This happens for free with DAX vs
shmem but we explicitly prevent shadow entries from being added to radix
trees for DAX mappings.

The only shadow entries that would be generated for DAX radix trees
would be to track zero page mappings that were created for holes.  These
pages would receive minimal benefit from having shadow entries, and the
choice to have only one type of exceptional entry in a given radix tree
makes the logic simpler both in clear_exceptional_entry() and in the
rest of DAX.
Signed-off-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jan Kara <jack@suse.com>
Cc: Jeff Layton <jlayton@poochiereds.net>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      f9fe48be
    • A
      wrappers for ->i_mutex access · 5955102c
      由 Al Viro 提交于 
      parallel to mutex_{lock,unlock,trylock,is_locked,lock_nested},
inode_foo(inode) being mutex_foo(&inode->i_mutex).

Please, use those for access to ->i_mutex; over the coming cycle
->i_mutex will become rwsem, with ->lookup() done with it held
only shared.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
      5955102c
  5. 16 1月, 2016 2 次提交
  7. 15 1月, 2016 2 次提交
    • A
      fs/block_dev.c:bdev_write_page(): use blk_queue_enter(..., GFP_NOIO) · b832861c
      由 Andrew Morton 提交于 
      bdev_write_page() is used by swapout and by writepage where we cannot
use __GFP_FS or __GFP_IO.  So it is misleading to mention GFP_KERNEL
here.

blk_queue_enter() only actually looks at __GFP_DIRECT_RECLAIM, so no
bugs were harmed in the making of this patch.

Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Jens Axboe <axboe@fb.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      b832861c
    • V
      kmemcg: account certain kmem allocations to memcg · 5d097056
      由 Vladimir Davydov 提交于 
      Mark those kmem allocations that are known to be easily triggered from
userspace as __GFP_ACCOUNT/SLAB_ACCOUNT, which makes them accounted to
memcg.  For the list, see below:

 - threadinfo
 - task_struct
 - task_delay_info
 - pid
 - cred
 - mm_struct
 - vm_area_struct and vm_region (nommu)
 - anon_vma and anon_vma_chain
 - signal_struct
 - sighand_struct
 - fs_struct
 - files_struct
 - fdtable and fdtable->full_fds_bits
 - dentry and external_name
 - inode for all filesystems. This is the most tedious part, because
   most filesystems overwrite the alloc_inode method.

The list is far from complete, so feel free to add more objects.
Nevertheless, it should be close to "account everything" approach and
keep most workloads within bounds.  Malevolent users will be able to
breach the limit, but this was possible even with the former "account
everything" approach (simply because it did not account everything in
fact).

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NVladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: NJohannes Weiner <hannes@cmpxchg.org>
Acked-by: NMichal Hocko <mhocko@suse.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Greg Thelen <gthelen@google.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      5d097056
  9. 14 1月, 2016 1 次提交
  11. 09 1月, 2016 2 次提交
  13. 07 1月, 2016 1 次提交
  15. 05 12月, 2015 1 次提交
    • I
      block: detach bdev inode from its wb in __blkdev_put() · 43d1c0eb
      由 Ilya Dryomov 提交于 
      Since 52ebea74 ("writeback: make backing_dev_info host
cgroup-specific bdi_writebacks") inode, at some point in its lifetime,
gets attached to a wb (struct bdi_writeback).  Detaching happens on
evict, in inode_detach_wb() called from __destroy_inode(), and involves
updating wb.

However, detaching an internal bdev inode from its wb in
__destroy_inode() is too late.  Its bdi and by extension root wb are
embedded into struct request_queue, which has different lifetime rules
and can be freed long before the final bdput() is called (can be from
__fput() of a corresponding /dev inode, through dput() - evict() -
bd_forget().  bdevs hold onto the underlying disk/queue pair only while
opened; as soon as bdev is closed all bets are off.  In fact,
disk/queue can be gone before __blkdev_put() even returns:

1499 static void __blkdev_put(struct block_device *bdev, fmode_t mode, int for_part)
1500 {
...
1518         if (bdev->bd_contains == bdev) {
1519                 if (disk->fops->release)
1520                         disk->fops->release(disk, mode);

[ Driver puts its references to disk/queue ]

1521         }
1522         if (!bdev->bd_openers) {
1523                 struct module *owner = disk->fops->owner;
1524
1525                 disk_put_part(bdev->bd_part);
1526                 bdev->bd_part = NULL;
1527                 bdev->bd_disk = NULL;
1528                 if (bdev != bdev->bd_contains)
1529                         victim = bdev->bd_contains;
1530                 bdev->bd_contains = NULL;
1531
1532                 put_disk(disk);

[ We put ours, the queue is gone
  The last bdput() would result in a write to invalid memory ]

1533                 module_put(owner);
...
1539 }

Since bdev inodes are special anyway, detach them in __blkdev_put()
after clearing inode's dirty bits, turning the problematic
inode_detach_wb() in __destroy_inode() into a noop.

add_disk() grabs its disk->queue since 523e1d39 ("block: make
gendisk hold a reference to its queue"), so the old ->release comment
is removed in favor of the new inode_detach_wb() comment.

Cc: stable@vger.kernel.org # 4.2+, needs backporting
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>
Acked-by: NTejun Heo <tj@kernel.org>
Tested-by: NRaghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Signed-off-by: NJens Axboe <axboe@fb.com>
      43d1c0eb
  17. 02 12月, 2015 1 次提交
  19. 20 11月, 2015 1 次提交
    • D
      block: protect rw_page against device teardown · 2e6edc95
      由 Dan Williams 提交于 
      Fix use after free crashes like the following:

 general protection fault: 0000 [#1] SMP
 Call Trace:
  [<ffffffffa0050216>] ? pmem_do_bvec.isra.12+0xa6/0xf0 [nd_pmem]
  [<ffffffffa0050ba2>] pmem_rw_page+0x42/0x80 [nd_pmem]
  [<ffffffff8128fd90>] bdev_read_page+0x50/0x60
  [<ffffffff812972f0>] do_mpage_readpage+0x510/0x770
  [<ffffffff8128fd20>] ? I_BDEV+0x20/0x20
  [<ffffffff811d86dc>] ? lru_cache_add+0x1c/0x50
  [<ffffffff81297657>] mpage_readpages+0x107/0x170
  [<ffffffff8128fd20>] ? I_BDEV+0x20/0x20
  [<ffffffff8128fd20>] ? I_BDEV+0x20/0x20
  [<ffffffff8129058d>] blkdev_readpages+0x1d/0x20
  [<ffffffff811d615f>] __do_page_cache_readahead+0x28f/0x310
  [<ffffffff811d6039>] ? __do_page_cache_readahead+0x169/0x310
  [<ffffffff811c5abd>] ? pagecache_get_page+0x2d/0x1d0
  [<ffffffff811c76f6>] filemap_fault+0x396/0x530
  [<ffffffff811f816e>] __do_fault+0x4e/0xf0
  [<ffffffff811fce7d>] handle_mm_fault+0x11bd/0x1b50

Cc: <stable@vger.kernel.org>
Cc: Jens Axboe <axboe@fb.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Reported-by: Nkbuild test robot <lkp@intel.com>
Acked-by: NMatthew Wilcox <willy@linux.intel.com>
[willy: symmetry fixups]
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
      2e6edc95
  21. 12 11月, 2015 1 次提交
  23. 22 10月, 2015 1 次提交
    • M
      block: Inline blk_integrity in struct gendisk · 25520d55
      由 Martin K. Petersen 提交于 
      Up until now the_integrity profile has been dynamically allocated and
attached to struct gendisk after the disk has been made active.

This causes problems because NVMe devices need to register the profile
prior to the partition table being read due to a mandatory metadata
buffer requirement. In addition, DM goes through hoops to deal with
preallocating, but not initializing integrity profiles.

Since the integrity profile is small (4 bytes + a pointer), Christoph
suggested moving it to struct gendisk proper. This requires several
changes:

 - Moving the blk_integrity definition to genhd.h.

 - Inlining blk_integrity in struct gendisk.

 - Removing the dynamic allocation code.

 - Adding helper functions which allow gendisk to set up and tear down
   the integrity sysfs dir when a disk is added/deleted.

 - Adding a blk_integrity_revalidate() callback for updating the stable
   pages bdi setting.

 - The calls that depend on whether a device has an integrity profile or
   not now key off of the bi->profile pointer.

 - Simplifying the integrity support routines in DM (Mike Snitzer).
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reported-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJens Axboe <axboe@fb.com>
      25520d55
  25. 16 9月, 2015 1 次提交
  27. 09 9月, 2015 1 次提交
    • M
      dax: move DAX-related functions to a new header · c94c2acf
      由 Matthew Wilcox 提交于 
      In order to handle the !CONFIG_TRANSPARENT_HUGEPAGES case, we need to
return VM_FAULT_FALLBACK from the inlined dax_pmd_fault(), which is
defined in linux/mm.h.  Given that we don't want to include <linux/mm.h>
in <linux/fs.h>, the easiest solution is to move the DAX-related
functions to a new header, <linux/dax.h>.  We could also have moved
VM_FAULT_* definitions to a new header, or a different header that isn't
quite such a boil-the-ocean header as <linux/mm.h>, but this felt like
the best option.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      c94c2acf
  29. 28 8月, 2015 1 次提交
  31. 21 8月, 2015 1 次提交
  33. 18 8月, 2015 1 次提交
  35. 05 7月, 2015 2 次提交
  37. 28 6月, 2015 1 次提交
  39. 26 6月, 2015 1 次提交
  41. 02 6月, 2015 2 次提交
    • T
      bdi: make inode_to_bdi() inline · a212b105
      由 Tejun Heo 提交于 
      Now that bdi definitions are moved to backing-dev-defs.h,
backing-dev.h can include blkdev.h and inline inode_to_bdi() without
worrying about introducing circular include dependency.  The function
gets called from hot paths and fairly trivial.

This patch makes inode_to_bdi() and sb_is_blkdev_sb() that the
function calls inline.  blockdev_superblock and noop_backing_dev_info
are EXPORT_GPL'd to allow the inline functions to be used from
modules.

While at it, make sb_is_blkdev_sb() return bool instead of int.

v2: Fixed typo in description as suggested by Jan.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reviewed-by: NJens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: NJens Axboe <axboe@fb.com>
      a212b105
    • T
      writeback: separate out include/linux/backing-dev-defs.h · 66114cad
      由 Tejun Heo 提交于 
      With the planned cgroup writeback support, backing-dev related
declarations will be more widely used across block and cgroup;
unfortunately, including backing-dev.h from include/linux/blkdev.h
makes cyclic include dependency quite likely.

This patch separates out backing-dev-defs.h which only has the
essential definitions and updates blkdev.h to include it.  c files
which need access to more backing-dev details now include
backing-dev.h directly.  This takes backing-dev.h off the common
include dependency chain making it a lot easier to use it across block
and cgroup.

v2: fs/fat build failure fixed.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reviewed-by: NJan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: NJens Axboe <axboe@fb.com>
      66114cad
  43. 25 4月, 2015 1 次提交
    • J
      direct-io: only inc/dec inode->i_dio_count for file systems · fe0f07d0
      由 Jens Axboe 提交于 
      do_blockdev_direct_IO() increments and decrements the inode
->i_dio_count for each IO operation. It does this to protect against
truncate of a file. Block devices don't need this sort of protection.

For a capable multiqueue setup, this atomic int is the only shared
state between applications accessing the device for O_DIRECT, and it
presents a scaling wall for that. In my testing, as much as 30% of
system time is spent incrementing and decrementing this value. A mixed
read/write workload improved from ~2.5M IOPS to ~9.6M IOPS, with
better latencies too. Before:

clat percentiles (usec):
 |  1.00th=[   33],  5.00th=[   34], 10.00th=[   34], 20.00th=[   34],
 | 30.00th=[   34], 40.00th=[   34], 50.00th=[   35], 60.00th=[   35],
 | 70.00th=[   35], 80.00th=[   35], 90.00th=[   37], 95.00th=[   80],
 | 99.00th=[   98], 99.50th=[  151], 99.90th=[  155], 99.95th=[  155],
 | 99.99th=[  165]

After:

clat percentiles (usec):
 |  1.00th=[   95],  5.00th=[  108], 10.00th=[  129], 20.00th=[  149],
 | 30.00th=[  155], 40.00th=[  161], 50.00th=[  167], 60.00th=[  171],
 | 70.00th=[  177], 80.00th=[  185], 90.00th=[  201], 95.00th=[  270],
 | 99.00th=[  390], 99.50th=[  398], 99.90th=[  418], 99.95th=[  422],
 | 99.99th=[  438]

In other setups, Robert Elliott reported seeing good performance
improvements:

https://lkml.org/lkml/2015/4/3/557

The more applications accessing the device, the worse it gets.

Add a new direct-io flags, DIO_SKIP_DIO_COUNT, which tells
do_blockdev_direct_IO() that it need not worry about incrementing
or decrementing the inode i_dio_count for this caller.

Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Elliott, Robert (Server Storage) <elliott@hp.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJens Axboe <axboe@fb.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
      fe0f07d0
  45. 16 4月, 2015 1 次提交
  47. 12 4月, 2015 5 次提交
  49. 26 3月, 2015 1 次提交
  51. 21 1月, 2015 2 次提交
  53. 14 1月, 2015 1 次提交
  55. 17 11月, 2014 1 次提交
    • B
      fs: add freeze_super/thaw_super fs hooks · 48b6bca6
      由 Benjamin Marzinski 提交于 
      Currently, freezing a filesystem involves calling freeze_super, which locks
sb->s_umount and then calls the fs-specific freeze_fs hook. This makes it
hard for gfs2 (and potentially other cluster filesystems) to use the vfs
freezing code to do freezes on all the cluster nodes.

In order to communicate that a freeze has been requested, and to make sure
that only one node is trying to freeze at a time, gfs2 uses a glock
(sd_freeze_gl). The problem is that there is no hook for gfs2 to acquire
this lock before calling freeze_super. This means that two nodes can
attempt to freeze the filesystem by both calling freeze_super, acquiring
the sb->s_umount lock, and then attempting to grab the cluster glock
sd_freeze_gl. Only one will succeed, and the other will be stuck in
freeze_super, making it impossible to finish freezing the node.

To solve this problem, this patch adds the freeze_super and thaw_super
hooks.  If a filesystem implements these hooks, they are called instead of
the vfs freeze_super and thaw_super functions. This means that every
filesystem that implements these hooks must call the vfs freeze_super and
thaw_super functions itself within the hook function to make use of the vfs
freezing code.
Reviewed-by: NJan Kara <jack@suse.cz>
Signed-off-by: NBenjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: NSteven Whitehouse <swhiteho@redhat.com>
      48b6bca6
  57. 31 10月, 2014 1 次提交
    • D
      Return short read or 0 at end of a raw device, not EIO · b2de525f
      由 David Jeffery 提交于 
      Author: David Jeffery <djeffery@redhat.com>
Changes to the basic direct I/O code have broken the raw driver when reading
to the end of a raw device.  Instead of returning a short read for a read that
extends partially beyond the device's end or 0 when at the end of the device,
these reads now return EIO.

The raw driver needs the same end of device handling as was added for normal
block devices.  Using blkdev_read_iter, which has the needed size checks,
prevents the EIO conditions at the end of the device.
Signed-off-by: NDavid Jeffery <djeffery@redhat.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
      b2de525f