In FIFOTH register, the RX_WMark field (bits[27:16]) defaults to
FIFO_DEPTH - 1. When reading it, bits[26:16] were being used, so
fix it to use the mask 0xfff instead of 0x7ff.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds support for the HS200 mode on the host side.
Also enables the tuning feature required when the HS200 mode
is selected.
Signed-off-by: NGirish K S <girish.shivananjappa@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds the support of the HS200 bus speed for eMMC 4.5 devices.
The eMMC 4.5 devices have support for 200MHz bus speed. The function
prototype of the tuning function is modified to handle the tuning
command number which is different in sd and mmc case.
Signed-off-by: NGirish K S <girish.shivananjappa@linaro.org>
Signed-off-by: NPhilip Rakity <prakity@marvell.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

In status register, fifo_count is bit[29:17].
(0x1FFF is correct)
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Turning the cache off implies flushing cache which doesn't define
maximum timeout unlike cache-on. This patch will apply the generic
CMD6 timeout only for cache-on. Additionally the kernel message is
added for checking failure case of cache-on.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

With the inclusion of following patch (59b5bc3929b37):
"mmc: sdhci: remove "state" argument from sdhci_suspend_host"

we get a compilation error for sdhci-spear:
drivers/mmc/host/sdhci-spear.c:283:2: error: too many arguments to function
‘sdhci_suspend_host’

This patch fixes this error.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

If there are errors happened in sdhci_suspend_host, handle it so that
when the function returns with an error, the host's behaviour is the
same before this function call, e.g. card detection is enabled and
tuning timer is active, etc.
Signed-off-by: NPhilip Rakity <prakity@marvell.com>
Signed-off-by: NAaron Lu <aaron.lu@amd.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

UHS_REG should be cleared for non-DDR mode. But currently there is
no way to clear DDR mode, if it is already set once. This patch adds
clearing DDR mode for non-DDR mode.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch fixes a failure to recognize SD cards reported on a Dell
Vostro with O2 Micro SD card reader.  Patch 49c468fc ("mmc: sd: add
support for uhs bus speed mode selection") caused the problem, by
setting the SDHCI_CTRL_HISPD flag even for legacy timings.
Signed-off-by: NAlexander Elbs <alex@segv.de>
Acked-by: NPhilip Rakity <prakity@marvell.com>
Acked-by: NArindam Nath <arindam.nath@amd.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

When suspending host, the tuning timer shoule be deactivated.
And the HOST_NEEDS_TUNING flag should be set after tuning timer is
deactivated.
Signed-off-by: NPhilip Rakity <prakity@marvell.com>
Signed-off-by: NAaron Lu <aaron.lu@amd.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Host may now use MMC_CAP2_NO_SLEEP_CMD to disable the use
of eMMC sleep/awake command.

This option can be used when your platform has a buggy
kernel crash dump software, which is supposed to store
the dump on the eMMC, but is not able to wake up the eMMC
from sleep state.

In particular, failures have been seen with u-boot; even if
it is fixed there, platforms will be slow to update their
bootloader binaries.
Signed-off-by: NUlf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: NHanumath Prasad <hanumath.prasad@stericsson.com>
Reviewed-by: NSrinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

As the card-detect irq handler just schedules work to be done by a
thread, we can use request_threaded_irq to do much of the work for
us.  This means that interrupts which arrive by handle_nested_irq
actually work.
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Tested-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NNeilBrown <neilb@suse.de>
Acked-by: NKishore Kadiyala <kishorek.kadiyala@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Runtime PM for SDIO is no longer enabled by default (see
5c7f0e08) so it must now
be enabled per platform, in this case Medfield uses it.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

To allow the set_clock host op to disable the SDCLK source when not
needed, always call the host op when the requested clock speed is
zero.  Do this even if host->clock already equals zero, because
the SDHCI driver may set that value (without calling the host op)
to force an update at the next (non-zero-speed) call.
Signed-off-by: NTodd Poynor <toddpoynor@google.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Even if a driver provides separate card detection, an interrupt
is still needed to abort mmc requests that are in progress.
SDHCI_QUIRK2_OWN_CARD_DETECTION prevents that, so remove it.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Retrieve the GPIO numbers for hardware reset and
card detect from platform data.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add a means of getting platform data for the SDHCI PCI
devices.  The data is stored against the slot not the
device in order to support multi-slot devices.

The data allows platform-specific setup (such as getting
GPIO numbers from firmware or setting up wl12xx for SDIO)
to be done in platform support files instead of the
sdhci-pci driver.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Do not enable card detection interrupts for non-removable cards.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Presently the vmmc regulator is enabled when the host
controller is added and disabled when it is removed.
However, the vmmc regulator should be under the control
of the upper layers via ->set_ios().  Make it so.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

While calling mmc_cache_ctrl() a host is not claimed. This patch
adds the mmc_try_claim_host() for quick response in suspend.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

MMC master clock rate can vary for each instance of the MMC controller
on the device. Use clk_get_rate instead to get the value.
Signed-off-by: NBalaji TK  <balajitk@ti.com>
Reviewed-by: NVenkatraman S <svenkatr@ti.com>
Tested-by: NHebbar, Gururaja <gururaja.hebbar@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch converts the sh_mmcif MMC host driver to process requests
asynchronously instead of waiting in its .request() method for completion.
This is achieved by using threaded IRQs.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch doesn't introduce any functional changes, it only simplifies
some code fragments, removes superfluous parameters, fixes typos.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

If an interrupt is coming with both error and data completion status bits
set, it has to be handled as an error interrupt, for which error interrupts
have to be processed first. The current version of the driver on the
contrary doesn't recognise such interrupts as an error event, which leads
to data corruption and breaks the error recovery.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds a primitive helper to support card hotplug detection on
platforms, where a GPIO, capable of producing interrupts, is used for
detection of card-insertion and -removal events.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

SD/MMC controllers provide different card insertion and removal detection
methods. On some of them the controller itself issues an interrupt, on
others polling is used, on yet others auxiliary means are used for this
purpose, e.g., a GPIO IRQ. Further, on some systems one of those methods
can be chosen at driver probing time and configured in software. E.g., on
some systems the SD/MMC controller card hot-plug detection pin can be
configured either as a respective controller functions, or an IRQ-capable
GPIO. To support such flexible configurations a card hot-plug context
is added by this patch.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch regroups the code slightly, adds documentation and allows
the rtpm counter of MMC_CAP_NEEDS_POLL devices to reach 0 again.
Signed-off-by: NBastian Hecht <hechtb@gmail.com>
[g.liakhovetski@gmx.de: restore pm_runtime_get_noresume()]
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch fixes the wrong comparison before setting the interface
voltage in DDR mode.

The assignment to the variable ddr before comaprison is either
ddr = MMC_1_2V_DDR_MODE; or ddr == MMC_1_8V_DDR_MODE. But the comparison
is done with the extended csd value if ddr == EXT_CSD_CARD_TYPE_DDR_1_2V.
Signed-off-by: NGirish K S <girish.shivananjappa@linaro.org>
Acked-by: NSubhash Jadavani <subhashj@codeaurora.org>
Acked-by: NPhilip Rakity <prakity@marvell.com>
Cc: <stable@kernel.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds the support for predefined multiple block r/w.
dw_mmc can support MMC_CAP_CMD23 capability.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds another capabilities field for MMC_CAPS2_XXX.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch modifies dw_mmc to use dev_pm_ops.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Kill block requests when the host realizes that the card is
removed from the slot and is sure that subsequent requests
are bound to fail. Do this silently so that the block
layer doesn't output unnecessary error messages.
Signed-off-by: NSujit Reddy Thumma <sthumma@codeaurora.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

c31b50e (mmc: core: Use delayed work in clock gating framework,
2011-11-14) missed a few things during review:

 o A useless pr_info()

 o milliseconds was written as two words

 o The sysfs file had units in its output

Fix all three problems.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Cc: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Enable boot partitions to be read-only locked until next power on via
a sysfs entry. There will be one sysfs entry for each boot partition:

/sys/block/mmcblkXbootY/ro_lock_until_next_power_on

Each boot partition is locked by writing 1 to its file.
Signed-off-by: NJohan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: NJohn Beckett <john.beckett@stericsson.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add pm_caps into platform_data. This is power management, usually
for SDIO device such as SDIO WLAN.
Signed-off-by: NSangwook Lee <sangwook.lee@samsung.com>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

sdhci-s3c updates pm_caps from platform data for SDIO PM.
Signed-off-by: NSangwook Lee <sangwook.lee@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>