Clearly ">=" was intended here instead of ">".
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This reduces our module init to a simple usb_register() call, so
that we can make use of the new upcoming macro's for this.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The code for this is rather crufty, and being able to tie a device
to a specific minor is not really something we want to support in
a modern udev based world.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The pwc driver used to:
1. kmalloc a buffer
2. memcpy data to send over usb there
3. do the usb_control_msg call (which does not work with data on the stack)
4. free the buffer

For every usb command send. This patch changes the code to instead malloc
a buffer for this purpose once and use it everywhere.

[mchehab@redhat.com: Fix a compilation breakage with allyesconfig:
 drivers/media/video/pwc/pwc-ctrl.c: In function ‘pwc_get_cmos_sensor’:
 drivers/media/video/pwc/pwc-ctrl.c:546:3: warning: passing argument 4 of ‘recv_control_msg’ makes integer from pointer without a cast [en$
 drivers/media/video/pwc/pwc-ctrl.c:107:12: note: expected ‘int’ but argument is of type ‘unsigned char *’
 drivers/media/video/pwc/pwc-ctrl.c:546:3: error: too many arguments to function ‘recv_control_msg’
 drivers/media/video/pwc/pwc-ctrl.c:107:12: note: declared here]
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Since we always do a set_video_mode on stream start, there is no need
to actually send the mode info to the device on a s_fmt / s_parm ioctl.
Not doing this saves us doing (slow) usb io.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Before this patch various code in the mode setting patch checked
pdev->pixfmt, but that was not set until the mode setting succeeded, so
it was looking at the old pixfmt! This patch fixes this by making the
pixfmt a parameter to set_video_mode, and setting it from set_video_mode
on success.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Instead of messing around with id's it's much easier to just compare
against a filehandle pointer.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

For some reason the cx18 driver could open the radio device only once.
Remove this limitation.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

For some reason the /dev/radio device was implemented as an exclusive open:
you could open it only once and not a second time.

Remove this limitation.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

As per the feature removal document, make the tuner type check more strict
so that it is no longer possible to set the radio frequency through a video
node or the TV frequency through a radio node.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

As Rupert pointed out, the phrase "It is good practice" should be replaced
with "You must".
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Cc: Rupert Eibauer <Rupert.Eibauer@ces.ch>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Update the spec to the behavior implemented by the control framework.
This should have been documented long ago but for some reason it was
never done.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The omap_vout driver has an output overlay, but never advertised that
capability.

The driver should also set the V4L2_FBUF_FLAG_OVERLAY flag.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
CC: Archit Taneja <archit@ti.com>
CC: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The zoran driver does not support this flag, so don't set it.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The error handling in the original code wasn't complete so static
checkers complained about a potential NULL deference.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The changeset 240ab508 is incomplete, as the first thing that
happens at cache clear is to do a memset with 0 to the cache.

So, the delivery system needs to be explicitly preserved there.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

As reported by Lawrence[1], MythTV 0.24.1 does the wrong thing
with a DVBv5 call: it fills the delivery system with
SYS_UNDEFINED, expecting that the DVB core would work with that.

This used to work by accident, as the DVB core were missing the
check for the supported delivery systems. Yet, fixing it
is easy, so let's add a logic to handle this case, to
provide backward compatibility.

[1] http://patchwork.linuxtv.org/patch/8314/Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

I added it by mistake. It is useless as no real hardware.
It even uses even Cypress FX2, general USB bridge chip, default IDs
that makes driver load all FX2 devices having default ID...
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Some time ago, Manoel sent us a patch adding more stuff
to the init sequence. However, his patch were also doing
non-related stuff, by changing the init logic without
any good reason. So, it was asked for him to submit a
patch with just the data that has changed, in order to
allow us to better analyze it.

As he didn't what it was requested, I finally found some
time to dig into his init sequence and add it here.

Basically, new stuff is added there. There are a few changes:

1) The removal of the extra (duplicated) logic that puts
   the chip into the serial mode;
2) Some Viterbi VBER measurement init data was changed from
   0x00 to 0xff for layer A, to match what was done for
   layers B and C.

None of those caused any regressions and both make sense
on my eyes.

The other parameters additions actually increased the
tuning quality for some channels. Yet, some channels that
were previously discovered with scan disappered, while
others appeared instead. This were tested in Brasilia,
with an external antena.

At the overall, it is now a little better. So, better to
add these, and then try to figure out a configuration that
would get even better scanning results.
Reported-by: NManoel Pinheiro <pinusdtv@hotmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

On mb86a20s, some registers have sub-addresses, while others not.
In order to make easier to compare different settings, group them.

No functional changes in this patch.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

As a DVBv3 application may be relying on the delivery system,
don't reset it at DTV_CLEAR. For DVBv5 applications, the
delivery system should be set anyway.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fix error where SNR unstable and jumps levels.
Signed-off-by: NMalcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

We can pass a NO_SIGNAL video decoder state back to applications
if it's available.
Signed-off-by: NSteven Toth <stoth@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Allow bridge drivers to query status.
Signed-off-by: NSteven Toth <stoth@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This remote was added with support for card Compro VideoMate M1F.

This remote is shipped with various Compro cards, not this one only.

Furthermore this remote can be bought separately under name Compro
VideoMate K100.
    http://compro.com.tw/en/product/k100/k100.html

So give it a proper name.

[mchehab@redhat.com: Fix the Makefile]
Signed-off-by: NSamuel Rakitničan <samuel.rakitnican@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fix the following build warning:

warning: (VIDEO_AU0828) selects DVB_AU8522 which has unmet direct dependencies (MEDIA_SUPPORT && DVB_CAPTURE_DRIVERS && DVB_CORE && I2C && VIDEO_V4L2)
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch converts the drivers in drivers/media/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.

Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: "Richard Röjfors" <richard.rojfors@pelagicore.com>
Cc: "Matti J. Aaltonen" <matti.j.aaltonen@nokia.com>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Muralidharan Karicheri <m-karicheri2@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Daniel Drake <dsd@laptop.org>
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Acked-by: NMatti J. Aaltonen <matti.j.aaltonen@nokia.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fix the following build warning:

warning: (VIDEO_CX231XX_DVB) selects DVB_MB86A20S which has unmet direct dependencies (MEDIA_SUPPORT && DVB_CAPTURE_DRIVERS && DVB_CORE && I2C)
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add driver for the JPEG codec IP block available in Samsung Exynos SoC series.

The driver is implemented as a V4L2 mem-to-mem device. It exposes two video
nodes to user space, one for the encoding part, and one for the decoding part.
Signed-off-by: NAndrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: NSakari Ailus <sakari.ailus@iki.fi>
Reviewed-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: NTomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Pixels were preferred units for selection rectangles over driver-dependent
units for almost all use cases. Therefore the units were fixed to pixels.
Signed-off-by: NTomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Adjusting of Video Processor's scaling factors was flawed. It bounded scaling
to range 1/16 to 1/1. The correct range should be 1/4 to 4/1. This patch fixes
this bug.
Signed-off-by: NTomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch add support for V4L2 selection API to s5p-tv driver.  Moreover it
removes old API for cropping.  Old applications would still work because the
crop ioctls are emulated using the selection API.
Signed-off-by: NTomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch allows new video drivers to work correctly with applications that
use the old-style crop API.  The old crop ioctl is emulated by using selection
callbacks.
Signed-off-by: NTomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds a documentation for VIDIOC_{G/S}_SELECTION ioctl. Moreover, the
patch adds the description of modeling of composing, cropping and scaling
features in V4L2. Finally, some examples are presented.
Signed-off-by: NTomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds images in binary format for the V4L2 selection API.
Signed-off-by: NTomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>