'pdata' is already dereferenced earlier. Hence this check is
meaningless.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

kfree on a null pointer is a no-op. Hence null check is not
necessary.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This patch converts the drivers to use the
module_platform_driver_probe() macro which makes the code smaller and
a bit simpler.
Signed-off-by: NFabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

module_platform_driver_probe() eliminates the boilerplate and simplifies
the code.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

dev_dbg should end with a new line.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Often a reading can be wrong. This patch assures that this is really a
pen up event and not a false reading.

Based on wm9712: pen up by Teresa Gámez and Christian Hemp.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Instead of interpreting a wrong measurement as pen up, we should
try to read again.

Based on wm9712: pen up by Teresa Gámez and Christian Hemp.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

With fast movements, there occured some out of screen jumps with my
touchscreen. The abs_x and abs_y module parameters should fix this by
default, but the driver doesn't actively checks the x/y coordinates.

Instead it seems that the input layer was supposed to drop out of range
inputs, as described in the comments:
"These parameters are used to help the input layer discard out of
range readings and reduce jitter etc"

The input layer documentation describes that values that are not in the
absolute range are also accepted.

So this patch adds a check within the driver.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

When it uses regulators the mms114 driver checks to see if it managed to
acquire regulators and ignores errors. This is not the intended usage and
not great style in general.

Since the driver already refuses to probe if it fails to allocate the
regulators simply make the enable and disable calls unconditional and
add appropriate error handling, including adding cleanup of the
regulators if setup_reg() fails.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

At least print a warning if we can't power the device up.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

There is a more complete atmel patch-series out by Nick Dyer that fixes
this and other things, but in the meantime this is the minimal thing to
get the touchscreen going on (at least my) Pixel Chromebook.

Not that I want my dirty fingers near that beautiful screen, but it
seems that a non-initialized touchscreen will also end up being a
constant wakeup source, so you have to disable it to go to sleep.  And
it's easier to just fix the initialization sequence.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This same driver can be used by atmel based touchscreens and touchpads
(buttonpads). Platform data may specify a device is a touchpad
using the is_tp flag.

This will cause the driver to perform some touchpad specific
initializations, such as:
  * register input device name "Atmel maXTouch Touchpad" instead of
  Touchscreen.
  * register BTN_LEFT & BTN_TOOL_* event types.
  * register axis resolution (as a fixed constant, for now)
  * register BUTTONPAD property
  * process GPIO buttons using reportid T19

Input event GPIO mapping is done by the platform data key_map array.

key_map[x] should contain the KEY or BTN code to send when processing
GPIOx from T19. To specify a GPIO as not an input source, populate
with KEY_RESERVED, or 0.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Signed-off-by: NBenson Leung <bleung@chromium.org>
Signed-off-by: NNick Dyer <nick.dyer@itdev.co.uk>
Tested-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This simplifies error unwinding and device teardown.
Tested-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Add the necessary code to create the needed platformdata from devicetree
informations.

The interrupt mode of the chip is not set via devicetree, as it is not
a property of the hardware but instead only a preferred type of operation.
This should probably be made settable via configfs in the future.
The option set as default is the mode the datasheet mentions as default.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

When supporting devicetree the platformdata may not necessarily come
from the dev but may be generated in the driver instead.

Therefore keep the pointer in the driver struct instead of using
dev.platform_data.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Devicetree based platforms don't handle device callbacks very well
and until now no board has come along that needs more extended hwinit
than pulling the rst gpio high.

Therefore pull the reset handling directly into the driver and remove
the callbacks from the driver.

If extended device setup is needed at some later point, power-sequences
would probably be the solution of choice.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Previously the gpio was not configured at all.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This enables autoloading of tsc2005 driver when is compiled as a module.
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

When removing the !S390 dependency from drivers/input/Kconfig a couple
of drivers don't compile because they have a dependency on GENERIC_HARDIRQS.
So add the missing dependencies.
Fixes e.g. this one:

drivers/input/keyboard/lm8323.c: In function ‘lm8323_suspend’:
drivers/input/keyboard/lm8323.c:801:2: error: implicit declaration of function ‘irq_set_irq_wake’
	[-Werror=implicit-function-declaration]

Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

When removing the !S390 dependency from drivers/input/Kconfig
a couple of drivers don't compile because they have a dependency
on GENERIC_HARDIRQS.  So add the missing dependencies.
Fixes e.g. this one:

drivers/input/keyboard/lm8323.c: In function ‘lm8323_suspend’:
drivers/input/keyboard/lm8323.c:801:2: error: implicit declaration of function ‘irq_set_irq_wake’
	[-Werror=implicit-function-declaration]
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Backing out changes made in earlier TTY removal patch.  Switched
to only one dependency in SERPORT on TTY instead of many incorrect
dependencies.
Signed-off-by: NJoe Millenbach <jmillenbach@gmail.com>
Reported-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The option allows you to remove TTY and compile without errors. This
saves space on systems that won't support TTY interfaces anyway.
bloat-o-meter output is below.

The bulk of this patch consists of Kconfig changes adding "depends on
TTY" to various serial devices and similar drivers that require the TTY
layer.  Ideally, these dependencies would occur on a common intermediate
symbol such as SERIO, but most drivers "select SERIO" rather than
"depends on SERIO", and "select" does not respect dependencies.

bloat-o-meter output comparing our previous minimal to new minimal by
removing TTY.  The list is filtered to not show removed entries with awk
'$3 != "-"' as the list was very long.

add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350)
function                                     old     new   delta
chr_dev_init                                 166     170      +4
allow_signal                                  80      82      +2
static.__warned                              143     142      -1
disallow_signal                               63      62      -1
__set_special_pids                            95      94      -1
unregister_console                           126     121      -5
start_kernel                                 546     541      -5
register_console                             593     588      -5
copy_from_user                                45      40      -5
sys_setsid                                   128     120      -8
sys_vhangup                                   32      19     -13
do_exit                                     1543    1526     -17
bitmap_zero                                   60      40     -20
arch_local_irq_save                          137     117     -20
release_task                                 674     652     -22
static.spin_unlock_irqrestore                308     260     -48
Signed-off-by: NJoe Millenbach <jmillenbach@gmail.com>
Reviewed-by: NJamey Sharp <jamey@minilop.net>
Reviewed-by: NJosh Triplett <josh@joshtriplett.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

devm_* APIs are device managed and make the exit and clean up code
simpler.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: Laxman Dewangan<ldewangan@nvidia.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

stmpe touchscreen supports BTN_TOUCH event but doesn't report it. Add
BTN_TOUCH reporting capability to the stmpe touchscreen driver.
Signed-off-by: NVipul Kumar Samar <vipulkumar.samar@st.com>
Reviewed-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The kernel does not contain the symbol SA1100_BITSY so the driver
is never compiled and can be removed safely.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Now we can register the BU21013_ts touch screen when booting with Device
Tree enabled. Here we parse all the necessary components previously
expected to be passed from platform data.
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

These GPIO init and exit functions have no place in platform data, they
should be part of the driver instead,
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Currently the BU21013 Touch Screen driver requests a regulator by the
name of 'V-TOUCH', which doesn't exist anywhere in the kernel. The
correct name, as referenced in platform regulator code is 'avdd'. Here,
when we request a regulator, we use the correct name instead.
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NJavier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

CONFIG_HOTPLUG is going away as an option so __devinitconst is no
longer needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

CONFIG_HOTPLUG is going away as an option so __devinitdata is no
longer needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This patch allows the STMPE Touchscreen driver to be successfully probed and
initialised when Device Tree support is enabled. Bindings are mentioned in
Documentation too.
Signed-off-by: NVipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Some platforms need the pendown GPIO debounce time setting programmed.
Since the pendown GPIO is handled by the driver, the debounce time
should also be handled along with the pendown GPIO request.
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Currently da9062_tsi does not probe and it fails as follows:

da9052 1-0048: Unable to determine device interrupts

Use the new da9052 irq functions and allow the driver to probe and operate
correctly.

Tested on mx53qsb board using 'evtest' tool.

Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: <linux-input@vger.kernel.org>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NVipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This patch frees stmpe-ts driver from burden of freeing resources :)
devm_* derivatives of multiple routines are used while allocating resources,
which would be freed automatically by kernel.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>