Make pci_setup_device() write the bus ID directly into the allotted storage,
rather than using pci_name() as the address as that now returns a const
pointer.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Convert printks to use dev_printk().

I converted pr_debug() to dev_dbg().  Both use KERN_DEBUG and are enabled
only when DEBUG is defined.

I converted printk(KERN_DEBUG) to dev_printk(KERN_DEBUG), not to dev_dbg(),
because dev_dbg() is only enabled when DEBUG is defined.

I converted DBG(KERN_INFO) (only in setup-bus.c) to dev_info().  The DBG()
name makes it sound like debug, but it's been enabled forever, so dev_info()
preserves the previous behavior.

I tried to make the resource assignment formats more consistent, e.g.,
  "BAR %d: got res [%#llx-%#llx] bus [%#llx-%#llx] flags %#lx\n"
instead of sometimes using "start-end" and sometimes using "size@start".
I'm not attached to one or the other; I'd just like them consistent.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Currently, /sys/bus/pci/slots/ only exposes hotplug attributes when a
hotplug driver is loaded, but PCI slots have attributes such as address,
speed, width, etc.  that are not related to hotplug at all.

Introduce pci_slot as the primary data structure and kobject model.
Hotplug attributes described in hotplug_slot become a secondary
structure associated with the pci_slot.

This patch only creates the infrastructure that allows the separation of
PCI slot attributes and hotplug attributes.  In this patch, the PCI
hotplug core remains the only user of this infrastructure, and thus,
/sys/bus/pci/slots/ will still only become populated when a hotplug
driver is loaded.

A later patch in this series will add a second user of this new
infrastructure and demonstrate splitting the task of exposing pci_slot
attributes from hotplug_slot attributes.

  - Make pci_slot the primary sysfs entity. hotplug_slot becomes a
    subsidiary structure.
    o pci_create_slot() creates and registers a slot with the PCI core
    o pci_slot_add_hotplug() gives it hotplug capability

  - Change the prototype of pci_hp_register() to take the bus and
    slot number (on parent bus) as parameters.

  - Remove all the ->get_address methods since this functionality is
    now handled by pci_slot directly.

[achiang@hp.com: rpaphp-correctly-pci_hp_register-for-empty-pci-slots]
Tested-by: NBadari Pulavarty <pbadari@us.ibm.com>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: make headers_check happy]
[akpm@linux-foundation.org: nuther build fix]
[akpm@linux-foundation.org: fix typo in #include]
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Cc: Greg KH <greg@kroah.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Len Brown <lenb@kernel.org>
Acked-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

If a device supports #PME and can generate PME events from D0, we may see
superfluous events before a driver is loaded (drivers should only enable PME as
needed), preventing suspend from working if the corresponding GPE was enabled.

Likewise, if the ACPI device has the _PRW object, the _PSW/_DSW object will be
called in order to disable the wakeup functionality. But when it is allowed to
wake up the sleeping state, OSPM will enable it again.

So we should disable PME in the course of scanning PCI devices and enable it
again only when PME events are actually required to be generated from the
requested PCI state (for example, D3_hot or D3_cold).  It is also safe to
disable PME again when the PME is disabled for the PCI devices.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NLi Shaohua <shaohua.li@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

so let pci_cfg_space_size call it directly without flag.
Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

scan AMD opteron io/mmio routing to make sure every pci root bus get correct
resource range. Thus later pci scan could assign correct resource to device
with unassigned resource.

this can fix a system without _CRS for multi pci root bus.
Signed-off-by: NYinghai Lu <yinghai.lu@sun.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

in the device_add, we try to use use parent numa_node.
need to make sure pci root bus's bridge device numa_node is set.
then we could use device->numa_node direclty for all device.
and don't need to call pcibus_to_node().
Signed-off-by: NYinghai Lu <yinghai.lu@sun.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

reuse pci_cfg_space_size but skip check pci express and pci-x CAP ID.
Signed-off-by: NYinghai Lu <yinghai.lu@sun.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

WARNING: drivers/pci/built-in.o(.text+0x150f): Section mismatch in reference from the function pci_scan_single_device() to the function .devinit.text:pci_scan_device()
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

WARNING: drivers/pci/built-in.o(.text+0xc4c): Section mismatch in reference from the function pci_add_new_bus() to the function .devinit.text:pci_alloc_child_bus()
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Done per Linus' request and suggestions. Linus has explained that
better than I'll be able to explain:

On Thu, Mar 27, 2008 at 10:12:10AM -0700, Linus Torvalds wrote:
> Actually, before we go any further, there might be a less intrusive
> alternative: add just a couple of flags to the resource flags field (we
> still have something like 8 unused bits on 32-bit), and use those to
> implement a generic "resource_alignment()" routine.
>
> Two flags would do it:
>
>  - IORESOURCE_SIZEALIGN: size indicates alignment (regular PCI device
>    resources)
>
>  - IORESOURCE_STARTALIGN: start field is alignment (PCI bus resources
>    during probing)
>
> and then the case of both flags zero (or both bits set) would actually be
> "invalid", and we would also clear the IORESOURCE_STARTALIGN flag when we
> actually allocate the resource (so that we don't use the "start" field as
> alignment incorrectly when it no longer indicates alignment).
>
> That wouldn't be totally generic, but it would have the nice property of
> automatically at least add sanity checking for that whole "res->start has
> the odd meaning of 'alignment' during probing" and remove the need for a
> new field, and it would allow us to have a generic "resource_alignment()"
> routine that just gets a resource pointer.

Besides, I removed IORESOURCE_BUS_HAS_VGA flag which was unused for ages.
Signed-off-by: NIvan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Vital Product Data (VPD) may be exposed by PCI devices in several
ways.  It is generally unsafe to read this information through the
existing interfaces to user-land because of stateful interfaces.

This adds:
- abstract operations for VPD access (struct pci_vpd_ops)
- VPD state information in struct pci_dev (struct pci_vpd)
- an implementation of the VPD access method specified in PCI 2.2
  (in access.c)
- a 'vpd' binary file in sysfs directories for PCI devices with VPD
  operations defined

It adds a probe for PCI 2.2 VPD in pci_scan_device() and release of
VPD state in pci_release_dev().
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

PCI Express ASPM defines a protocol for PCI Express components in the D0
state to reduce Link power by placing their Links into a low power state
and instructing the other end of the Link to do likewise. This
capability allows hardware-autonomous, dynamic Link power reduction
beyond what is achievable by software-only controlled power management.
However, The device should be configured by software appropriately.
Enabling ASPM will save power, but will introduce device latency.

This patch adds ASPM support in Linux. It introduces a global policy for
ASPM, a sysfs file /sys/module/pcie_aspm/parameters/policy can control
it. The interface can be used as a boot option too. Currently we have
below setting:
        -default, BIOS default setting
        -powersave, highest power saving mode, enable all available ASPM
state and clock power management
        -performance, highest performance, disable ASPM and clock power
management
By default, the 'default' policy is used currently.

In my test, power difference between powersave mode and performance mode
is about 1.3w in a system with 3 PCIE links.

Note: some devices might not work well with aspm, either because chipset
issue or device issue. The patch provide API (pci_disable_link_state),
driver can disable ASPM for specific device.
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The PCI bus names included in /proc/iomem and /proc/ioports are
of the form 'PCI Bus #XX' where XX is the bus number.  This patch
changes the naming to 'PCI Bus XXXX:YY' where XXXX is the domain
number and YY is the bus number.  For example, PCI bus 14 in
domain 0 will show as 'PCI Bus 0000:14' instead of 'PCI Bus #14'.
This change makes the naming consistent with other architectures
such as ia64 where multiple PCI domain support has been around
longer.
Signed-off-by: NGary Hade <garyhade@us.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch finally removes the global list of PCI devices.  We are
relying entirely on the list held in the driver core now, and do not
need a separate "shadow" list as no one uses it.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This lets us check if the device is really added to the driver core or
not, which is what we need when walking some of the bus lists.  The flag
is there in anticipation of getting rid of the other PCI device list,
which is what we used to check in this situation.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

no_pci_devices() should use the driver core list of PCI devices, not our
"separate" one.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

  * Cleaned up references to cpumask_scnprintf() and added new
    cpulist_scnprintf() interfaces where appropriate.

  * Fix some small bugs (or code efficiency improvments) for various uses
    of cpumask_scnprintf.

  * Clean up some checkpatch errors.
Signed-off-by: NMike Travis <travis@sgi.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Fix following warning:
WARNING: vmlinux.o(.text+0x47bdb1): Section mismatch in reference from the function pci_scan_child_bus() to the function .devinit.text:pcibios_fixup_bus()

We had plenty of functions that could be annotated __devinit but due to
the former restriction that exported symbols could not be annotated
they were not so.  So annotate these function and fix the references
from the pci/hotplug/* code to silence the resuting warnings.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds PCI's accessor for segment_boundary_mask in device_dma_parameters.

The default segment_boundary is set to 0xffffffff, same to the block layer's
default value (and the scsi mid layer uses the same value).
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds struct device_dma_parameters in struct pci_dev and properly
sets up a pointer in struct device.

The default max_segment_size is set to 64K, same to the block layer's
default value.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Mostly-acked-by: NJeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: NJens Axboe <jens.axboe@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The following warnings were issued during build of
drivers/pci with an allyesconfig build:
WARNING: o-x86_64/drivers/pci/built-in.o(.text+0xdaf): Section mismatch in reference from the function pci_add_new_bus() to the function .devinit.text:pci_alloc_child_bus()
WARNING: o-x86_64/drivers/pci/built-in.o(.text+0x15e2): Section mismatch in reference from the function pci_scan_single_device() to the function .devinit.text:pci_scan_device()
WARNING: o-x86_64/drivers/pci/built-in.o(.text+0x1b0c5): Section mismatch in reference from the function pci_bus_assign_resources() to the function .devinit.text:pci_setup_bridge()
WARNING: o-x86_64/drivers/pci/built-in.o(.text+0x1b32d): Section mismatch in reference from the function pci_bus_size_bridges() to the function .devinit.text:pci_bus_size_cardbus()

Investigating each case closer it looked like all
referred functions are only used in the init phase
or during hotplug.
So to avoid wasting too much memory in the non-hotplug
case the simpler fix was to allow the fuctions to
use code/data from the __devinit sections.
This was done in all four case by adding the __ref
annotation.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix following warnings:
WARNING: o-x86_64/drivers/pci/built-in.o(.text+0xb054): Section mismatch in reference from the function cpci_configure_slot() to the function .devinit.text:pci_do_scan_bus()
WARNING: o-x86_64/drivers/pci/built-in.o(.text+0x153ab): Section mismatch in reference from the function shpchp_configure_device() to the function .devinit.text:pci_do_scan_bus()
WARNING: o-x86_64/drivers/pci/built-in.o(__ksymtab+0xc0): Section mismatch in reference from the variable __ksymtab_pci_do_scan_bus to the function .devinit.text:pci_do_scan_bus()

PCI hotplug were the only user of pci_do_scan_bus()
so moving this function to a separate file that is build
only when we enable CONFIG_HOTPLUG_PCI.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This reverts commit 6c723d5b.

It caused build errors on non-x86 platforms, config file confusion, and
even some boot errors on some x86-64 boxes.  All around, not quite ready
for prime-time :(

Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This moves the pci_bus class device to be a real struct device and at
the same time, place it in the device tree in the correct location.

Note, the old "bridge" symlink is now gone, but this was a non-standard
link and no userspace program used it.  If you need to determine the
device that the bus is on, follow the standard device symlink, or walk
up the device tree.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

PCI Express ASPM defines a protocol for PCI Express components in the D0
state to reduce Link power by placing their Links into a low power state
and instructing the other end of the Link to do likewise. This
capability allows hardware-autonomous, dynamic Link power reduction
beyond what is achievable by software-only controlled power management.
However, The device should be configured by software appropriately.
Enabling ASPM will save power, but will introduce device latency.

This patch adds ASPM support in Linux. It introduces a global policy for
ASPM, a sysfs file /sys/module/pcie_aspm/parameters/policy can control
it. The interface can be used as a boot option too. Currently we have
below setting:
        -default, BIOS default setting
        -powersave, highest power saving mode, enable all available ASPM
state
and clock power management
        -performance, highest performance, disable ASPM and clock power
management
By default, the 'default' policy is used currently.

In my test, power difference between powersave mode and performance mode
is about 1.3w in a system with 3 PCIE links.
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NJoe Perches <joe@perches.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There's already a prototype for pci_scan_child_bus() at the correct place in
pci.h, so there's no reason for an additional one.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes the following build error with CONFIG_HOTPLUG=n:

  MODPOST 2137 modules
ERROR: "pci_scan_single_device" [drivers/edac/i82875p_edac.ko] undefined!
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Acked-by: NDoug Thompson <norsk5@yahoo.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch removes the following unused exports:
- remove the following unused EXPORT_SYMBOL's:
 - pci-acpi.c: pci_osc_support_set
 - proc.c: pci_proc_detach_bus
- remove the following unused EXPORT_SYMBOL_GPL's:
  - bus.c: pci_walk_bus
  - probe.c: pci_create_bus
  - setup-res.c: pci_claim_resource
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This allows an easier way to get to the device klist associated with a
struct bus_type (you have three to choose from...)  This will make it
easier to move these fields to be dynamic in a future patch.

The only user of this is the PCI core which horribly abuses this
interface to rearrange the order of the pci devices.  This should be
done using the existing bus device walking functions, but that's left
for future patches.

Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

It appears that some PCI-E bridges do the wrong thing in the presense of
CRS Software Visibility and MMCONFIG.  In particular, it looks like an
ATI bridge (device ID 7936) will return 0001 in the vendor ID field of
any bridged devices indefinitely.

Not enabling CRS SV avoids the problem, and as we currently do not
really make good use of the feature anyway (we just time out rather than
do any threaded discovery as suggested by the CRS specs), we're better
off just not enabling it.

This should fix a slew of problem reports with random devices (generally
graphics adapters or fairly high-performance networking cards, since it
only affected PCI-E) not getting properly recognized on these AMD systems.

If we really want to use CRS-SV, we may end up eventually needing a
whitelist of systems where this should be enabled, along with some kind
of "pcibios_enable_crs()" query to call the system-specific code.
Suggested-by: NLoic Prylli <loic@myri.com>
Tested-by: NKai Ruhnau <kai@tragetaschen.dyndns.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Restore PCI expansion ROM P2P prefetch window creation.

This patch reverts previous "Avoid creating P2P prefetch
window for expansion ROMs" change due to regressions that
were spotted on some systems.
Signed-off-by: NGary Hade <garyhade@us.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This reverts commit fd6e7321, which
helped up things on MIPS, but was wrong for everything else.  As Ralf
Baechle puts it:

  "It seems the whole MIPS resource managment is complicated enough (out
   of necessity) that only a few people actually grok it.  Ioports being
   actually memory mapped on MIPS only makes the confusion worse, sigh."
Requested-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NAlan Cox <alan@redhat.com>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When devices are under a p2p bridge, upstream transactions get replaced by the
device id of the bridge as it owns the PCIE transaction.  Hence its necessary
to setup translations on behalf of the bridge as well.  Due to this limitation
all devices under a p2p share the same domain in a DMAR.

We just cache the type of device, if its a native PCIe device
or not for later use.

[akpm@linux-foundation.org: BUG_ON -> WARN_ON+recover]
Signed-off-by: NAnil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Modify PCI Bridge Control ISA flag for clarity

This patch changes PCI_BRIDGE_CTL_NO_ISA to PCI_BRIDGE_CTL_ISA
and modifies it's clarifying comment and locations where used.
The change reduces the chance of future confusion since it makes
the set/unset meaning of the bit the same in both the bridge
control register and bridge_ctl field of the pci_bus struct.
Signed-off-by: NGary Hade <garyhade@us.ibm.com>
Acked-by: NLinas Vepstas <linas@austin.ibm.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Avoid creating P2P prefetch window for expansion ROMs

Because of the future possibility that P2P prefetch windows will contain
address ranges above 4GB some BIOSes are providing space in the P2P
non-prefetch windows for expansion ROMs.  This is due to expansion ROM
BAR 32-bit limitation.  When expansion ROM BARs without BIOS assigned
address(es) are currently found behind a P2P bridge, the kernel attempts
to create a P2P prefetch window for them even though space for them has
already been provided in the non-prefetch window.  _CRS on some systems
with certain resource conservation conscious BIOSes may not provide the
extra 1MB or more memory resource needed for the expansion ROM motivated
prefetch window causing resource allocation errors.

This change corrects the problem by removing IORESOURCE_PREFETCH from
the expansion ROM flags initialization.  It also removes
IORESOURCE_CACHEABLE which seems inappropriate if only non-cacheable
memory is available.
Signed-off-by: NGary Hade <gary.hade@us.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Skip ISA ioresource alignment on some systems

To conserve limited PCI i/o resource on some IBM multi-node systems, the
BIOS allocates (via _CRS) and expects the kernel to use addresses in
ranges currently excluded by pcibios_align_resource() [i386/pci/i386.c].
This change allows the kernel to use the currently excluded address
ranges on the IBM x3800, x3850, and x3950.
Signed-off-by: NGary Hade <gary.hade@us.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I got the following error on MIPS Cobalt.

PCI: Unable to reserve I/O region #1:8@f00001f0 for device 0000:00:09.1
pata_via 0000:00:09.1: failed to request/iomap BARs for port 0 (errno=-16)
PCI: Unable to reserve I/O region #3:8@f0000170 for device 0000:00:09.1
pata_via 0000:00:09.1: failed to request/iomap BARs for port 1 (errno=-16)
pata_via 0000:00:09.1: no available native port

The legacy mode IDE resources set the following order.

pci_setup_device()
    Legacy mode ATA controllers have fixed addresses.
    IDE resources: 0x1F0-0x1F7, 0x3F6, 0x170-0x177, 0x376
    |
    V
pcibios_fixup_bus()
    MIPS Cobalt PCI bus regions have the -0x10000000 offset from PCI resources.
    pcibios_fixup_bus() fix PCI bus regions.
    0x1F0 - 0x10000000 = 0xF00001F0
    |
    V
ata_pci_init_one()
    PCI: Unable to reserve I/O region #1:8@f00001f0 for device 0000:00:09.1

In some architectures, PCI bus regions have the offset from PCI resources. 
For this reason, pci_setup_device() should set PCI bus regions to
dev->resource[].

[akpm@linux-foundation.org: use struct initialiser]
Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

On MIPS with PCI && !HOTPLUG, I'm currently getting the following modpost
warning:

  MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x1ce128): Section mismatch: reference to .init.text:pci_read_bridge_bases (between 'pcibios_fixup_bus' and 'pcibios_enable_device')

On MIPS I have the call chains pci_scan_child_bus -> pcibios_fixup_bus ->
pci_read_bridge_bases.  pci_scan_child_bus can't be __devinit because it
it is an exported symbol, thus pcibios_fixup_bus and pci_read_bridge_bases
can't be either.

For some reason I don't see this issue on x86; I blame compiler differences.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>