Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

If device fail to initialize we can OOPS in rt2x00lib_remove_dev(), due
to using uninitialized usb_anchor structure:

[  855.435820] ieee80211 phy3: rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x1000 with error -19
[  855.435826] ieee80211 phy3: rt2800_probe_rt: Error - Invalid RT chipset 0x0000, rev 0000 detected
[  855.435829] ieee80211 phy3: rt2x00lib_probe_dev: Error - Failed to allocate device
[  855.435845] BUG: unable to handle kernel NULL pointer dereference at 0000000000000028
[  855.435900] IP: _raw_spin_lock_irq+0xd/0x30
[  855.435926] PGD 0
[  855.435953] Oops: 0002 [#1] SMP
<snip>
[  855.437011] Call Trace:
[  855.437029]  ? usb_kill_anchored_urbs+0x27/0xc0
[  855.437061]  rt2x00lib_remove_dev+0x190/0x1c0 [rt2x00lib]
[  855.437097]  rt2x00lib_probe_dev+0x246/0x7a0 [rt2x00lib]
[  855.437149]  ? ieee80211_roc_setup+0x9e/0xd0 [mac80211]
[  855.437183]  ? __kmalloc+0x1af/0x1f0
[  855.437207]  ? rt2x00usb_probe+0x13d/0xc50 [rt2x00usb]
[  855.437240]  rt2x00usb_probe+0x155/0xc50 [rt2x00usb]
[  855.437273]  rt2800usb_probe+0x15/0x20 [rt2800usb]
[  855.437304]  usb_probe_interface+0x159/0x2d0
[  855.437333]  driver_probe_device+0x2bb/0x460

Patch changes initialization sequence to fix the problem.

Cc: Vishal Thanki <vishalthanki@gmail.com>
Fixes: 8b4c0009 ("rt2x00usb: Use usb anchor to manage URB")
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We might kill TX or RX urb during rt2x00usb_flush_entry(), what can
cause anchor list corruption like shown below:

[ 2074.035633] WARNING: CPU: 2 PID: 14480 at lib/list_debug.c:33 __list_add+0xac/0xc0
[ 2074.035634] list_add corruption. prev->next should be next (ffff88020f362c28), but was dead000000000100. (prev=ffff8801d161bb70).
<snip>
[ 2074.035670] Call Trace:
[ 2074.035672]  [<ffffffff813bde47>] dump_stack+0x63/0x8c
[ 2074.035674]  [<ffffffff810a2231>] __warn+0xd1/0xf0
[ 2074.035676]  [<ffffffff810a22af>] warn_slowpath_fmt+0x5f/0x80
[ 2074.035678]  [<ffffffffa073855d>] ? rt2x00usb_register_write_lock+0x3d/0x60 [rt2800usb]
[ 2074.035679]  [<ffffffff813dbe4c>] __list_add+0xac/0xc0
[ 2074.035681]  [<ffffffff81591c6c>] usb_anchor_urb+0x4c/0xa0
[ 2074.035683]  [<ffffffffa07322af>] rt2x00usb_kick_rx_entry+0xaf/0x100 [rt2x00usb]
[ 2074.035684]  [<ffffffffa0732322>] rt2x00usb_clear_entry+0x22/0x30 [rt2x00usb]

To fix do not anchor TX and RX urb's, it is not needed as during
shutdown we kill those urbs in rt2x00usb_free_entries().

Cc: Vishal Thanki <vishalthanki@gmail.com>
Fixes: 8b4c0009 ("rt2x00usb: Use usb anchor to manage URB")
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

As reported by Felix:

Though protected by an ifdef, introducing an usb symbol dependency in
the rt2x00lib module is a major inconvenience for distributions that
package kernel modules split into individual packages.

Get rid of this unnecessary dependency by calling the usb related
function from a more suitable place.

Cc: Vishal Thanki <vishalthanki@gmail.com>
Reported-by: NFelix Fietkau <nbd@nbd.name>
Fixes: 8b4c0009 ("rt2x00usb: Use usb anchor to manage URB")
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When we restart system using sysrq RT3290 device do not initalize
properly, hance always enable it via WLAN_FUN_CTRL register on
probe.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=85461Reported-and-tested-by: NGiedrius Statkevičius <edrius.statkevicius@gmail.com>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

clk_get() takes two arguments and might return ERR_PTR(), so we
have to nullify pointer on that case, to do not break further call
to clk_get_rate().
Reported-by: NFelix Fietkau <nbd@nbd.name>
Fixes: 34db70b9 ("rt2x00: add copy of clk for soc devices")
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Support for the RT5350 WiSoC was added to OpenWrt after having a
lengthy debate about the legality of the original submission, see
https://lists.openwrt.org/pipermail/openwrt-devel/2013-January/018224.html
MTK/Ralink Acked replied and says we can merge this patch under the GPL.
https://dev.openwrt.org/changeset/36177Signed-off-by: NSerge Vasilugin <vasilugin@yandex.ru>
Tested-by: NMichel Stempin <michel.stempin@wanadoo.fr>
Acked-by: NJohn Crispin <blogic@openwrt.org>
[daniel@makrotopia.org: added commit message, cleaned up code]
Signed-off-by: NDaniel Golle <daniel@makrotopia.org>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

On Rt3352 the driver needs to know the frequency of an external
crystal which can be either 40 MHz (as on all other WiSoCs until now)
or 20 MHz.
Get the clock attached by ramips WiSoC platform code which probes
SYSC_REG_SYSCFG (added by John Crispin in commit 6ac8579b) and
introduce a new flag clk_is_20mhz in struct hw_mode_spec to make the
driver aware and use either 40 MHz or 20 MHz specific rf_vals on those
WiSoC platforms.
The introduced support for boards with a 20 MHz crystal is also needed
for RT5350.
Signed-off-by: NDaniel Golle <daniel@makrotopia.org>
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NMathias Kresin <dev@kresin.me>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Since clk_get() is not trivial add copy of clk pointer to rt2x00dev
for System On Chip devices and initialize it on probe routine.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NDaniel Golle <daniel@makrotopia.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This is needed for WiFi to work e.g. on DIR-615 rev.H1 which got
external RF power amplifiers connected to the WiSoC.
Signed-off-by: NDaniel Golle <daniel@makrotopia.org>
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NDaniel Golle <daniel@makrotopia.org>
Acked-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Simple patch to correct HT20/HT40 filter setting.
Tested with Rt3290, Rt3352 and Rt5350
Signed-off-by: NSerge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: NDaniel Golle <daniel@makrotopia.org>
Acked-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Since rt2800pci update beacon settings asynchronously from
tbtt tasklet, without beacon_skb_mutex protection, number of
currently active beacons entries can be different than
number pointed by rt2x00dev->intf_beaconing. Remove warning
about that inconsistency.

Reported-by: evaxige@qq.com
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

All Ralink USB devices I have, including old ones, work well with
max_psdu = 3 (64kB tx AMPDUs).

Fix indent on the way.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

If we do not get TX status in reasonable time, we most likely fail to
send frame hence mark it as so.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Enable RTS frame retry fall-back and limit number of RTS retries to 7
what is default number of retries for small frames. As RTS/CTS is used
for TXOP protection, those settings prevent posting lots of RTS
frames when remote station do not response with CTS at the moment. After
sending 7 RTS's the HW will start back-off mechanism and after it will
start posing RTS again to get access to the medium.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We do not have option to set per frame retry count. We have only global
TX_RTY_CFG registers which specify the number or retries. Set setting
of that register to value that correspond rate control algorithm number
of frame post (number of retries + 1), which is 3 for aggregated frames.
This should help with big amount of retries on bad conditions, hence
mitigate buffer-bloat like problems.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Reset tuner use curr_band value, make sure it is updated.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When medium is busy or frames have to be resend, it takes time to send
the frames and get TX status from hardware. For some really bad medium
conditions it can take seconds. Patch change TX status timeout to give
HW more time to provide it, however 500ms is not enough for bad
conditions. In the future this timeout should be removed and replaced
with proper watchdog mechanism.

Increase flush timeout accordingly as well.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

On rt2800usb, if we do not get TX status from HW, we assume frames were
posted and after entry->last_action timeout, we forcibly provide TX
status to mac80211. So it's not possible to detect hardware TX hung
based on the timeout. Additionally TXRQ_PCNT tells on number of frames
in the Packet Buffer (buffer between bus interface and chip MAC
subsystem), which can be non zero on normal conditions. To check HW hung
we will need provide some different mechanism, for now remove watchdog
as current implementation is wrong and not useful.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Do not perform mac80211 config and link_tuner at the same time,
this can possibly result in wrong RF or BBP configuration.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

msleep(1) can sleep much more time then requested 1ms, this is not good
on channel switch, which we want to be performed fast (i.e. to make scan
faster). Replace msleep() with usleep_range(), which has much smaller
maximum sleeping time boundary.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This procedure can sleep, hence mdelay is not needed.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We need to perform different actions (AGC and VCO calibrations and VGC
tuning) periodically at different intervals. We don't need separate
works for those, we can use link tuner work and just check for proper
interval on it.

This fixes performing AGC and VCO calibration when scanning on STA
mode. We need to be on-channel to perform those calibrations.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Since we reset TX_PIN_CFG register, we have to finish recalibration.
Warn if this is not possible.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We have different modes of adjusting freq offset on different chips.
Call current adjustment similarly like vendor driver - mode1 .
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

MAX_LEN_CFG_MAX_PSDU specify maximum transmitted by HW AMPDU length
(0 - 8kB, 1 - 16kB, 2 - 32kB, 3 - 64kB). Set this option according to
remote stations capabilities (based on HT ampdu_factor). However limit
the value based our hardware TX capabilities as some chips can not send
more than 16kB (factor 1). Limit for all chips is currently 32kB
(factor 2), but perhaps for some chips this could be increased
to 64kB by setting drv_data->max_psdu to 3.

Since MAX_LEN_CFG_MAX_PSDU is global setting, on multi stations modes
(AP, IBSS, mesh) we limit according to less capable remote STA. We can
not set bigger value to speed up communication with some stations and
do not break communication with slow stations.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Do not set ampdu_density and ba_size for frames without AMPDU bit i.e.
frames that will not be aggregated to AMPDU.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Initalize max ampdu_factor supported by us based on rx chains, vendor
driver do the same.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>

Sending frames in CCK rates on HT can cause performance problems.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Use RTS/CTS protection for TXOP on all rates modes as default and
disable CCK rates (this cause performance problems).
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Change default to RTS/CTS protection. This has a cost of transmitting
one more control frame (RTS) however protect us from traffic from
hidden node.

On station mode will use CTS-to-self if AP will configure that
for the network.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Those TX_SW_CFG1 values are used in vendor driver.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Initialize AUTO_RSP_CFG register to similar value as vendor driver does.

Do not set BAC_ACK_POLICY based on short preamble setting, those are
unrelated.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We already initlized WPDMA_GLO_CFG_WP_DMA_BURST_SIZE to 3 on
rt2800_init_registers() for USB devices. For PCI devices we will use
HW default setting, which is 2, so patch does not change behaviour
on PCI devices.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>