Add per queue Tx and Rx packet and byte counts.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the dynamic debug support to output information about the hardware
features reported by the device.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently whenever the driver needs to enable or disable interrupts for
a DMA channel it reads the interrupt enable register (IER), updates the
value and then writes the new value back to the IER. Since the hardware
does not change the IER, software can track this value and elimiate the
need to read it each time.

Add the IER value to the channel related data structure and use that as
the base for enabling and disabling interrupts, thus removing the need
for the MMIO read.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add some additional dynamic debug message to the driver. The new messages
will provide additional information about the PCS window calculation.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Many of the names used by the driver are based upon the name of the device
found during device probe.  Move the formatting of the names into the
device open function so that any renaming that occurs before the device is
brought up will be accounted for.  This also means moving the creation of
some named workqueues into the device open path.

Add support to register for net events so that if a device is renamed
the corresponding debugfs directory can be renamed.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When transmitting a TSO packet, the driver only increments the TSO packet
statistic by one rather than the number of total packets that were sent.
Update the driver to record the total number of packets that resulted from
TSO transmit.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sometimes when the driver is being unloaded while the devices are still
up the driver can issue errors.  This is based on timing and the double
invocation of some routines.  The phy_exit() call needs to be run after
the network device has been closed and unregistered from the system.
Also, the phy_exit() does not need to invoke phy_stop() since that will
be called as part of the device closing, so remove that call.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When running in SGMII mode at speeds below 1000Mbps, the auto-negotition
control register must set the MII control width for the MAC interface
to be 8-bits wide.  By default the width is 4-bits.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the MDIO mode is set to none for the 10000Base-T, which is
incorrect.  The MDIO mode should for this configuration should be
clause 45.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, if vport is zero then then an uninialized return status
in err is returned.  Since the only return status at the end of the
function esw_add_uc_addr is zero for the current set of return paths
we may as well just return 0 rather than err to fix this issue.

Detected by CoverityScan, CID#1452698 ("Uninitialized scalar variable")

Fixes: eeb66cdb ("net/mlx5: Separate between E-Switch and MPFS")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use errno -ENOSPC ("No space left on device") when the XDP xmit
have no space left on the TX ring buffer, instead of -ENOMEM.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Acked-by: NJohn Fastabend <john.fastabend@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix Smatch error by not dereferencing iq pointer if it's NULL.

See http://marc.info/?l=kernel-janitors&m=150296723301129&w=2

Also, remove unnecessary parentheses.

Fixes: d314ac22 ("liquidio: moved liquidio_napi_poll to lio_core.c")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NIntiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the static check warning due to missing handling leg of
unsupported L3 protocol type in the hns3_get_l4_protocol() function.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for
hip08 SoC")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the static check error warning in hns3_get_link_ksettings()
function by re-arranging the code.

Fixes: 496d03e9 ("net: hns3: Add Ethtool support to HNS3 Driver")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the missing u64_stats_fetch_begin_irq() while trying to
atomically do 64-bit RX/TX fetch. We did not get any error during test
as our SoC is 64-bit so all of these seq/lock operations results in NOOP.

As such, this seq lock supports has been added for the sake of completion
if this code ever runs on 32-bit platform and we are trying to do 64-bit
stats fetch.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for
hip08 SoC")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The offending commit used a newly added helper function.
But the logic is wrong. Without this fix, the affected NICs
can't do HW offload. Error -EOPNOTSUPP will be returned directly.

Fixes: a2e8da93 ("net/sched: use newly added classid identity helpers")
Signed-off-by: NChris Mi <chrism@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Issue credits BEFORE enabling DROQ's; this prevents PKTPF_ERR interrupt.
Signed-off-by: NRick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Add support for PF FLR when exiting
   (enables CORE_DRV_ACTIVE upon next driver init)
2. Skip some initialization (don't try to load f/w, activate consoles).
Signed-off-by: NRick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

vio_device_id are not supposed to change at runtime. All functions
working with vio_device_id provided by <asm/vio.h> work with
const vio_device_id. So mark the non-const structs as const.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

vio_device_id are not supposed to change at runtime. All functions
working with vio_device_id provided by <asm/vio.h> work with
const vio_device_id. So mark the non-const structs as const.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Media type is only set if h->ae_algo->ops->get_media_type is called
so there is a possibility that media_type is uninitialized when it is
used a switch statement.  Fix this by initializing media_type to
HNAE3_MEDIA_TYPE_UNKNOWN.

Detected by CoverityScan, CID#1452624("Uninitialized scalar variable")

Fixes: 496d03e9 ("net: hns3: Add Ethtool support to HNS3 driver")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Trivial fix to spelling mistake in dev_info message
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Trivial fix to spelling mistakes in the mlx4 driver
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NYuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that control message processing occurs in a workqueue rather than a BH
handler MTU updates received from the firmware may be safely processed.
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Processing of control messages is not time-critical and future processing
of some messages will require taking the RTNL which is not possible
in a BH handler. It seems simplest to move all control message processing
to a workqueue.
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pnp_device_id are not supposed to change at runtime. All functions
working with pnp_device_id provided by <linux/pnp.h> work with
const pnp_device_id. So mark the non-const structs as const.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A VF's MTU is capped at the parent PF's MTU.  So if there's a change in the
PF's MTU, then update the VF's netdev->max_mtu.

Also remove duplicate log messages for MTU change.
Signed-off-by: NVeerasenareddy Burru <veerasenareddy.burru@cavium.com>
Signed-off-by: NRaghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The kernel coding style is to treat sizeof as a function
(ie. with parenthesis) not as an operator.

Also use kcalloc and kmalloc_array
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Reviewed-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

adding support for ethtool --set-channels feature
Signed-off-by: NIntiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: NRaghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moving common octeon_setup_interrupt to lio_core.c
Signed-off-by: NIntiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: NRaghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moving liquidio_legacy_intr_handler to lio_core.c
Signed-off-by: NIntiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: NRaghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moving common liquidio_msix_intr_handler to lio_core.c
Signed-off-by: NIntiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: NRaghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MAC stats command takes a port ID, which doesn't exist on
pre-ef10 NICs (5000- and 6000- series). This is extracted from the
NIC specific data; we misinterpret this as the ef10 data structure,
causing us to read potentially unallocated data. With a KASAN kernel
this can cause errors with:
   BUG: KASAN: slab-out-of-bounds in efx_mcdi_mac_stats

Fixes: 0a2ab4d9 ("sfc: set the port-id when calling MC_CMD_MAC_STATS")
Reported-by: NStefano Brivio <sbrivio@redhat.com>
Tested-by: NStefano Brivio <sbrivio@redhat.com>
Signed-off-by: NBert Kenward <bkenward@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I made an embarrassing mistake and used 'IPV6' instead of 'CONFIG_IPV6'
around the function that updates the kernel about IPv6 neighbours
activity. This can be a problem if the kernel has more neighbours than a
certain threshold and it starts deleting those that are supposedly
inactive.

Fixes: b5f3e0d4 ("mlxsw: spectrum_router: Fix build when IPv6 isn't enabled")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IPv6 routes currently lack nexthop flags as in IPv4. This has several
implications.

In the forwarding path, it requires us to check the carrier state of the
nexthop device and potentially ignore a linkdown route, instead of
checking for RTNH_F_LINKDOWN.

It also requires capable drivers to use the user facing IPv6-specific
route flags to provide offload indication, instead of using the nexthop
flags as in IPv4.

Add nexthop flags to IPv6 routes in the 40 bytes hole and use it to
provide offload indication instead of the RTF_OFFLOAD flag, which is
removed while it's still not part of any official kernel release.

In the near future we would like to use the field for the
RTNH_F_{LINKDOWN,DEAD} flags, but this change is more involved and might
not be ready in time for the current cycle.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not necessary to manually clear the
device driver data to NULL.

Cc: Joe Jin <joe.jin@oracle.com>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: NZhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not necessary to manually clear the
device driver data to NULL.

Cc: Joe Jin <joe.jin@oracle.com>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: NZhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The fw_type module parameter isn't showing up in the
/sys/module/liquidio/parameters directory.  Fix it by setting the read
permission bits for user, group, other in module_param_string().  Revise
the description of fw_type.  Initialize the fw_type static char array with
the default value to conform to the module parameter description.
Signed-off-by: NDerek Chickles <derek.chickles@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>