Add a support function to find a DSS output by given name. This is used
in later patches to link the panels to DSS outputs.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

omapdss output drivers always read the platform data. This crashes when
there's no platform data when using DT.

Add a check to read the platform data only if it exists.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We can currently set the default display (i.e. the initial display) in
the omapdss platform data by using a pointer to the default
omap_dss_device. Internally omapdss uses the device's name to resolve
the default display.

As it's difficult to get the omap_dss_device pointer in the future,
after we've changed the omapdss device model, this patch adds a new way
to define the default display, by using the name of the display.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>

This patch fixes warnings due to missing lock on write error path.

  WARNING: at fs/hpfs/hpfs_fn.h:353 hpfs_truncate+0x75/0x80 [hpfs]()
  Hardware name: empty
  Pid: 26563, comm: dd Tainted: P           O 3.9.4 #12
  Call Trace:
    hpfs_truncate+0x75/0x80 [hpfs]
    hpfs_write_begin+0x84/0x90 [hpfs]
    _hpfs_bmap+0x10/0x10 [hpfs]
    generic_file_buffered_write+0x121/0x2c0
    __generic_file_aio_write+0x1c7/0x3f0
    generic_file_aio_write+0x7c/0x100
    do_sync_write+0x98/0xd0
    hpfs_file_write+0xd/0x50 [hpfs]
    vfs_write+0xa2/0x160
    sys_write+0x51/0xa0
    page_fault+0x22/0x30
    system_call_fastpath+0x1a/0x1f
Signed-off-by: NMikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Cc: stable@kernel.org  # 2.6.39+
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull timer fixes from Thomas Gleixner:

 - Trivial: unused variable removal

 - Posix-timers: Add the clock ID to the new proc interface to make it
   useful.  The interface is new and should be functional when we reach
   the final 3.10 release.

 - Cure a false positive warning in the tick code introduced by the
   overhaul in 3.10

 - Fix for a persistent clock detection regression introduced in this
   cycle

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timekeeping: Correct run-time detection of persistent_clock.
  ntp: Remove unused variable flags in __hardpps
  posix-timers: Show clock ID in proc file
  tick: Cure broadcast false positive pending bit warning

Pull irqdomain bug fixes from Grant Likely:
 "This branch contains a set of straight forward bug fixes to the
  irqdomain code and to a couple of drivers that make use of it."

* tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux:
  irqchip: Return -EPERM for reserved IRQs
  irqdomain: document the simple domain first_irq
  kernel/irq/irqdomain.c: before use 'irq_data', need check it whether valid.
  irqdomain: export irq_domain_add_simple

The irqdomain core will report a log message for any attempted map call
that fails unless the error code is -EPERM. This patch changes the
Versatile irq controller drivers to use -EPERM because it is normal for
a subset of the IRQ inputs to be marked as reserved on the various
Versatile platforms.
Signed-off-by: NGrant Likely <grant.likely@linaro.org>

The first_irq needs to be zero to get a linear domain and that
comes with special semantics. We want to simplify this going
forward but some documentation never hurts.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@linaro.org>

Since irq_data may be NULL, if so, we WARN_ON(), and continue, 'hwirq'
which related with 'irq_data' has to initialize later, or it will cause
issue.
Signed-off-by: NChen Gang <gang.chen@asianux.com>
Signed-off-by: NGrant Likely <grant.likely@linaro.org>

All other irq_domain_add_* functions are exported already, and apparently
this one got left out by mistake, which causes build errors for ARM
allmodconfig kernels:

ERROR: "irq_domain_add_simple" [drivers/gpio/gpio-rcar.ko] undefined!
ERROR: "irq_domain_add_simple" [drivers/gpio/gpio-em.ko] undefined!
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NGrant Likely <grant.likely@linaro.org>

Pull ARM SoC fixes from Olof Johansson:
 "Another week, another batch of fixes for arm-soc platforms.

  Nothing controversial here, a handful of fixes for regressions and/or
  serious problems across several of the platforms.  Things are slowing
  down nicely on fix rates for 3.10"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: exynos: add debug_ll_io_init() call in exynos_init_io()
  ARM: EXYNOS: uncompress - print debug messages if DEBUG_LL is defined
  ARM: shmobile: sh73a0: Update CMT clockevent rating to 80
  sh-pfc: r8a7779: Don't group USB OVC and PENC pins
  ARM: mxs: icoll: Fix interrupts gpio bank 0
  ARM: imx: clk-imx6q: AXI clock select index is incorrect
  ARM: bcm2835: override the HW UART periphid
  ARM: mvebu: Fix bug in coherency fabric low level init function
  ARM: Kirkwood: TS219: Fix crash by double PCIe instantiation
  ARM: ux500: Provide supplies for AUX1, AUX2 and AUX3
  ARM: ux500: Only configure wake-up reasons on ux500 based platforms
  ARM: dts: imx: fix clocks for cspi
  ARM i.MX6q: fix for ldb_di_sels

Pull MIPS fixes from Ralf Baechle:
 "MIPS fixes across the field.  The only area that's standing out is the
  exception handling which received it's dose of breakage as part of the
  microMIPS patchset"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: ralink: add missing SZ_1M multiplier
  MIPS: Compat: Fix cputime_to_timeval() arguments in compat binfmt_elf.
  MIPS: OCTEON: Improve _machine_halt implementation.
  MIPS: rtlx: Fix implicit declaration of function set_vi_handler()
  MIPS: Trap exception handling fixes
  MIPS: Quit exposing Kconfig symbols in uapi headers.
  MIPS: Remove duplicate definition of check_for_high_segbits.

Pull m68knommu fix from Greg Ungerer:
 "A single fix for compilation breakage to many of the ColdFire CPU
  targets"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
  m68k: only use local gpio_request_one if not using GPIOLIB

Pull drm fixes from Dave Airlie:
 "Regression fixers for the big 3:

   - nouveau: hdmi audio, dac load detect, s/r regressions fixed
   - radeon: long standing system hang fixed, hdmi audio and rs780 fast
     fb fixes
   - intel: one old regression, a WARN removal, and a stop X dying fix

  Otherwise one mgag200 fix, a couple of arm build fixes, and a core use
  after free fix."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/nv50/kms: use dac loadval from vbios, where it's available
  drm/nv50/disp: force dac power state during load detect
  drm/nv50-nv84/fifo: fix resume regression introduced by playlist race fix
  drm/nv84/disp: Fix HDMI audio regression
  drm/i915/sdvo: Use &intel_sdvo->ddc instead of intel_sdvo->i2c for DDC.
  drm/radeon: don't allow audio on DCE6
  drm/radeon: Use direct mapping for fast fb access on RS780/RS880 (v2)
  radeon: Fix system hang issue when using KMS with older cards
  drm/i915: no lvds quirk for hp t5740
  drm/i915: Quirk the pipe A quirk in the modeset state checker
  drm/i915: Fix spurious -EIO/SIGBUS on wedged gpus
  drm/mgag200: Add missing write to index before accessing data register
  drm/nouveau: use mdelay instead of large udelay constants
  drm/tilcd: select BACKLIGHT_LCD_SUPPORT
  drm: fix a use-after-free when GPU acceleration disabled

Pull slave-dmaengine fixes from Vinod Koul:
 "Fix from Andy is for dmatest regression reported by Will and Rabin has
  fixed runtime ref counting for st_dma40"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dmatest: do not allow to interrupt ongoing tests
  dmaengine: ste_dma40: fix pm runtime ref counting

Merge tag 'trace-fixes-v3.10-rc3-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull tracing fixes from Steven Rostedt:
 "This contains 4 fixes.

  The first two fix the case where full RCU debugging is enabled,
  enabling function tracing causes a live lock of the system.  This is
  due to the added debug checks in rcu_dereference_raw() that is used by
  the function tracer.  These checks are also traced by the function
  tracer as well as cause enough overhead to the function tracer to slow
  down the system enough that the time to finish an interrupt can take
  longer than when the next interrupt is triggered, causing a live lock
  from the timer interrupt.

  Talking this over with Paul McKenney, we came up with a fix that adds
  a new rcu_dereference_raw_notrace() that does not perform these added
  checks, and let the function tracer use that.

  The third commit fixes a failed compile when branch tracing is
  enabled, due to the conversion of the trace_test_buffer() selftest
  that the branch trace wasn't converted for.

  The forth patch fixes a bug caught by the RCU lockdep code where a
  rcu_read_lock() is performed when rcu is disabled (either going to or
  from idle, or user space).  This happened on the irqsoff tracer as it
  calls task_uid().  The fix here was to use current_uid() when possible
  that doesn't use rcu locking.  Which luckily, is always used when
  irqsoff calls this code."

* tag 'trace-fixes-v3.10-rc3-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Use current_uid() for critical time tracing
  tracing: Fix bad parameter passed in branch selftest
  ftrace: Use the rcu _notrace variants for rcu_dereference_raw() and friends
  rcu: Add _notrace variation of rcu_dereference_raw() and hlist_for_each_entry_rcu()

Commit 9f29ab11 ("ACPI / scan: do not match drivers against objects
having scan handlers") introduced a boot regression on Tony's ia64 HP
rx2600.  Tony says:

  "It panics with the message:

   Kernel panic - not syncing: Unable to find SBA IOMMU: Try a generic or DIG kernel

   [...] my problem comes from arch/ia64/hp/common/sba_iommu.c
   where the code in sba_init() says:

        acpi_bus_register_driver(&acpi_sba_ioc_driver);
        if (!ioc_list) {

   but because of this change we never managed to call ioc_init()
   so ioc_list doesn't get set up, and we die."

Revert it to avoid this breakage and we'll fix the problem it attempted
to address later.
Reported-by: NTony Luck <tony.luck@gmail.com>
Cc: 3.9+ <stable@vger.kernel.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

From Shawn Guo, mxs fixes for 3.10:

- Since the time we move to MULTI_IRQ_HANDLER, the 0x7f polling for no
  interrupt in icoll_handle_irq() becomes insane, because 0x7f is an
  valid interrupt number, the irq of gpio bank 0.  That unnecessary
  polling results in the driver not detecting when irq 0x7f is active
  which makes the machine effectively dead lock.  The fix removes the
  interrupt poll loop and allows usage of gpio0 interrupt without an
  infinite loop.

* tag 'mxs-fixes-3.10' of git://git.linaro.org/people/shawnguo/linux-2.6:
  ARM: mxs: icoll: Fix interrupts gpio bank 0
Signed-off-by: NOlof Johansson <olof@lixom.net>

From Shawn Guo, imx fixes for 3.10, take 2:

- One device tree fix for all spi node to have per clock added.
  The clock is needed by spi driver to calculate bit rate divisor.
  The spi node in the current device trees either does not have the
  clock or is defined as dummy clock, in which case the driver probe
  will fail or spi will run at a wrong bit rate.

- Two imx6q clock fixes, which correct axi_sels and ldb_di_sels.

* tag 'imx-fixes-3.10-2' of git://git.linaro.org/people/shawnguo/linux-2.6:
  ARM: imx: clk-imx6q: AXI clock select index is incorrect
  ARM: dts: imx: fix clocks for cspi
  ARM i.MX6q: fix for ldb_di_sels
Signed-off-by: NOlof Johansson <olof@lixom.net>

If the early MMU mapping of the UART happens to get booted out of the
TLB between the start of paging_init() and when we finally re-add the
UART at the very end of s3c_init_cpu(), we'll get a hang at bootup if
we've got early_printk enabled.  Avoid this hang by calling
debug_ll_io_init() early.

Without this patch, you can reliably reproduce a hang when early
printk is enabled by adding flush_tlb_all() at the start of
exynos_init_io().  After this patch the hang goes away.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'renesas-fixes-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes

From Simon Horman, Renesas ARM based SoC fixes for v3.10:
- Correction to USB OVC and PENC pin groupings on r8a7779 SoC.
  This avoids conflicts when the USB_OVCn pins are used by another function.
  This has been observed to be a problem in v3.10-rc1.
- Update CMT clock rating for sh73a0 SoC to resolve boot failure
  on kzm9g-reference. This resolves a regression between v3.9 and v3.10-rc1.

* tag 'renesas-fixes-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: sh73a0: Update CMT clockevent rating to 80
  sh-pfc: r8a7779: Don't group USB OVC and PENC pins
Signed-off-by: NOlof Johansson <olof@lixom.net>

Printing low-level debug messages make an assumption that the specified
UART port has been preconfigured by the bootloader. Incorrectly
specified UART port results in system getting stalled while printing the
message "Uncompressing Linux... done, booting the kernel"
This UART port number is specified through S3C_LOWLEVEL_UART_PORT. Since
the UART port might different for different board, it is not possible to
specify it correctly for every board that use a common defconfig file.

Calling this print subroutine only when DEBUG_LL fixes the problem. By
disabling DEBUG_LL in default config file, we would be able to boot
multiple boards with different default UART ports.

With this current approach, we miss the print "Uncompressing Linux...
done, booting the kernel." when DEBUG_LL is not defined.
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Pull infiniband fixes from Roland Dreier:
 - qib RCU/lockdep fix
 - iser device removal fix, plus doc fixes

* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB/qib: Fix lockdep splat in qib_alloc_lkey()
  MAINTAINERS: Add entry for iSCSI Extensions for RDMA (iSER) initiator
  IB/iser: Add Mellanox copyright
  IB/iser: Fix device removal flow

Pull vfio fix from Alex Williamson:
 "fix rmmod crash"

* tag 'vfio-v3.10-rc5' of git://github.com/awilliam/linux-vfio:
  vfio: fix crash on rmmod

Merge tag 'ecryptfs-3.10-rc5-msync' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs

Pull ecryptfs fixes from Tyler Hicks:
 - Fixes how eCryptfs handles msync to sync both the upper and lower
   file
 - A couple of MAINTAINERS updates

* tag 'ecryptfs-3.10-rc5-msync' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  eCryptfs: Check return of filemap_write_and_wait during fsync
  Update eCryptFS maintainers
  ecryptfs: fixed msync to flush data

Pull CIFS fix from Steve French:
 "Fix one byte buffer overrun with prefixpaths on cifs mounts which can
  cause a problem with mount depending on the string length"

* 'for-3.10' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: fix off-by-one bug in build_unc_path_to_root

When user interrupts ongoing transfers the dmatest may end up with console
lockup, oops, or data mismatch. This patch prevents user to abort any ongoing
test.

Documentation is updated accordingly.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Reported-by: NWill Deacon <will.deacon@arm.com>
Tested-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Pull sound fixes from Takashi Iwai:
 - A pile of small regression fix patches for HD-audio VIA codecs
 - Quirks for HD-aduio and USB-audio devices
 - A trivial SIS7019 error path fix

* tag 'sound-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: usb-audio - Fix invalid volume resolution on Logitech HD webcam c270
  ALSA: usb-audio - Apply Logitech QuickCam Pro 9000 quirk only to audio iface
  ALSA: hda/via - Clean up duplicated codes
  ALSA: hda/via - Fix wrongly cleared pins after suspend on VT1802
  ALSA: hda - Add keep_eapd_on flag to generic parser
  ALSA: hda - Allow setting automute/automic hooks after parsing
  ALSA: hda/via - Disable broken dynamic power control
  ALSA: usb-audio: fix Roland/Cakewalk UM-3G support
  ALSA: hda - Add headset quirk for two Dell machines
  ALSA: hda - add dock support for Thinkpad T431s
  ALSA: sis7019: fix error return code in sis_chip_create()

Pull power management and ACPI fixes from Rafael J Wysocki:

 - Fix for an ACPI PM regression causing Toshiba P870-303 to crash
   during boot from Rafael J Wysocki.

 - ACPI fix for an issue causing some drivers to attempt to bind to
   devices they shouldn't touch from Aaron Lu.

 - Fix for a recent cpufreq regression related to a possible race with
   CPU offline from Michael Wang.

 - ACPI cpufreq regression fix for an issue causing turbo frequencies to
   be underutilized in some cases from Ross Lagerwall.

 - cpufreq-cpu0 driver fix related to incorrect clock ACPI usage from
   Guennadi Liakhovetski.

 - HP WMI driver fix for an issue causing GPS initialization and
   poweroff failures on HP Elitebook 6930p from Lan Tianyu.

 - APEI (ACPI Platform Error Interface) fix for an issue in the error
   code path in ghes_probe() from Wei Yongjun.

 - New ACPI video driver blacklist entries for HP m4 and HP Pavilion g6
   from Alex Hung and Ash Willis.

* tag 'pm+acpi-3.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / PM: Do not execute _PS0 for devices without _PSC during initialization
  cpufreq: cpufreq-cpu0: use the exact frequency for clk_set_rate()
  cpufreq: protect 'policy->cpus' from offlining during __gov_queue_work()
  ACPI / scan: do not match drivers against objects having scan handlers
  ACPI / APEI: fix error return code in ghes_probe()
  acpi-cpufreq: set current frequency based on target P-State
  ACPI / video: ignore BIOS initial backlight value for HP Pavilion g6
  ACPI / video: ignore BIOS initial backlight value for HP m4
  x86 / platform / hp_wmi: Fix bluetooth_rfkill misuse in hp_wmi_rfkill_setup()

* pm-fixes:
  cpufreq: cpufreq-cpu0: use the exact frequency for clk_set_rate()
  cpufreq: protect 'policy->cpus' from offlining during __gov_queue_work()
  acpi-cpufreq: set current frequency based on target P-State

* acpi-fixes:
  ACPI / PM: Do not execute _PS0 for devices without _PSC during initialization
  ACPI / scan: do not match drivers against objects having scan handlers
  ACPI / APEI: fix error return code in ghes_probe()
  ACPI / video: ignore BIOS initial backlight value for HP Pavilion g6
  ACPI / video: ignore BIOS initial backlight value for HP m4
  x86 / platform / hp_wmi: Fix bluetooth_rfkill misuse in hp_wmi_rfkill_setup()

Commit b3785492 (ACPI / PM: Do not power manage devices in unknown
initial states) added code to force devices without _PSC, but having
_PS0 defined in the ACPI namespace, into ACPI power state D0 by
executing _PS0 for them.  That turned out to break Toshiba P870-303,
however, so revert that code.

References: https://bugzilla.kernel.org/show_bug.cgi?id=58201Reported-and-tested-by: NJerome Cantenot <jerome.cantenot@gmail.com>
Tracked-down-by: NLan Tianyu <tianyu.lan@intel.com>
Cc: 3.9+ <stable@vger.kernel.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Pull networking fix from David Miller:
 "This is a quick one commit pull request to cure the regression
  introduced by the MSG_CMSG_COMPAT change."

(Background: commit 1be374a0 completely broke 32-bit COMPAT handling
by not only disallowing MSG_CMSG_COMPAT from user APIs, but clearing it
in our own internal use too!)

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net: Unbreak compat_sys_{send,recv}msg

Pull staging driver fixes from Greg Kroah-Hartman:
 "Here are some staging and IIO driver fixes for the 3.10-rc5 release.

  All of them are tiny, and fix a number of reported issues (build and
  runtime)"
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

* tag 'staging-3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  iio:inkern: Fix typo/bug in convert raw to processed.
  iio: frequency: ad4350: Fix bug / typo in mask
  inkern: iio_device_put after incorrect return/goto
  staging: alarm-dev: information leak in alarm_compat_ioctl()
  iio:callback buffer: free the scan_mask
  staging: alarm-dev: information leak in alarm_ioctl()
  drivers: staging: zcache: fix compile error
  staging: dwc2: fix value of dma_mask

Pull tty/serial driver fixes from Greg Kroah-Hartman:
 "Here are some small bugfixes, and one revert, of serial driver issues
  that have been reported"

* tag 'tty-3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  Revert "serial: 8250: Make SERIAL_8250_RUNTIME_UARTS work correctly"
  serial: samsung: enable clock before clearing pending interrupts during init
  serial/imx: disable hardware flow control at startup

Pull USB fixes from Greg Kroah-Hartman:
 "Here are a number of USB bugfixes and new device ids for the 3.10-rc5
  tree.

  Nothing major here, a number of new device ids (and movement from the
  option to the zte_ev driver of a number of ids that we had previously
  gotten wrong, some xhci bugfixes, some usb-serial driver fixes that
  were recently found, some host controller fixes / reverts, and a
  variety of smaller other things"

* tag 'usb-3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (29 commits)
  USB: option,zte_ev: move most ZTE CDMA devices to zte_ev
  USB: option: blacklist network interface on Huawei E1820
  USB: whiteheat: fix broken port configuration
  USB: serial: fix TIOCMIWAIT return value
  USB: mos7720: fix hardware flow control
  USB: keyspan: remove unused endpoint-array access
  USB: keyspan: fix bogus array index
  USB: zte_ev: fix broken open
  USB: serial: Add Option GTM681W to qcserial device table.
  USB: Serial: cypress_M8: Enable FRWD Dongle hidcom device
  USB: EHCI: fix regression related to qh_refresh()
  usbfs: Increase arbitrary limit for USB 3 isopkt length
  USB: zte_ev: fix control-message timeouts
  USB: mos7720: fix message timeouts
  USB: iuu_phoenix: fix bulk-message timeout
  USB: ark3116: fix control-message timeout
  USB: mos7840: fix DMA to stack
  USB: mos7720: fix DMA to stack
  USB: visor: fix initialisation of Treo/Kyocera devices
  USB: serial: fix Treo/Kyocera interrrupt-in urb context
  ...

Pull PCI fixes from Bjorn Helgaas:
 "This fixes a crash when booting a 32-bit kernel via the EFI boot stub.

  PCI ROM from EFI
      x86/PCI: Map PCI setup data with ioremap() so it can be in highmem"

* tag 'pci-v3.10-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  x86/PCI: Map PCI setup data with ioremap() so it can be in highmem

Pull more xfs updates from Ben Myers:
 "Here are several fixes for filesystems with CRC support turned on:
  fixes for quota, remote attributes, and recovery.  There is also some
  feature work related to CRCs: the implementation of CRCs for the inode
  unlinked lists, disabling noattr2/attr2 options when appropriate, and
  bumping the maximum number of ACLs.

  I would have preferred to defer this last category of items to 3.11.
  This would require setting a feature bit for the on-disk changes, so
  there is some pressure to get these in 3.10.  I believe this
  represents the end of the CRC related queue.

   - Rework of dquot CRCs
   - Fix for remote attribute invalidation of a leaf
   - Fix ordering of transaction replay in recovery
   - Implement CRCs for inode unlinked list
   - Disable noattr2/attr2 mount options when CRCs are enabled
   - Bump the limitation of ACL entries for v5 superblocks"

* tag 'for-linus-v3.10-rc5' of git://oss.sgi.com/xfs/xfs:
  xfs: increase number of ACL entries for V5 superblocks
  xfs: disable noattr2/attr2 mount options for CRC enabled filesystems
  xfs: inode unlinked list needs to recalculate the inode CRC
  xfs: fix log recovery transaction item reordering
  xfs: fix remote attribute invalidation for a leaf
  xfs: rework dquot CRCs

I broke them in this commit:

    commit 1be374a0
    Author: Andy Lutomirski <luto@amacapital.net>
    Date:   Wed May 22 14:07:44 2013 -0700

        net: Block MSG_CMSG_COMPAT in send(m)msg and recv(m)msg

This patch adds __sys_sendmsg and __sys_sendmsg as common helpers that accept
MSG_CMSG_COMPAT and blocks MSG_CMSG_COMPAT at the syscall entrypoints.  It
also reverts some unnecessary checks in sys_socketcall.

Apparently I was suffering from underscore blindness the first time around.
Signed-off-by: NAndy Lutomirski <luto@amacapital.net>
Tested-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>