Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 03 12月, 2006 16 次提交
    • T
      [PATCH] libata: always use polling IDENTIFY · 800b3996
      由 Tejun Heo 提交于 
      libata switched to IRQ-driven IDENTIFY when IRQ-driven PIO was
introduced.  This has caused a lot of problems including device
misdetection and phantom device.

ATA_FLAG_DETECT_POLLING was added recently to selectively use polling
IDENTIFY on problemetic drivers but many controllers and devices are
affected by this problem and trying to adding ATA_FLAG_DETECT_POLLING
for each such case is diffcult and not very rewarding.

This patch makes libata always use polling IDENTIFY.  This is
consistent with libata's original behavior and drivers/ide's behavior.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
      800b3996
    • J
      [libata] pata_cs5535: fix build · 3ac551a6
      由 Jeff Garzik 提交于 
      Noticed by Tejun and others.
Signed-off-by: NJeff Garzik <jeff@garzik.org>
      3ac551a6
    • T
      [PATCH] ahci: do not powerdown during initialization · 8e16f941
      由 Tejun Heo 提交于 
      ahci_init_controller() calls ahci_deinit_port() to make sure the
controller is stopped before initializing the controller.  In turn,
ahci_deinit_port() invokes ahci_power_down() to power down the port.
If the controller supports slumber mode, the link is put into it.

Unfortunately, some devices don't implement link powersaving mode
properly and show erratic behavior after link is put into slumber
mode.  For example, HL-DT-ST DVD-RAM GSA-H30N completely locks up on
slumber transition and can only be recovered with the *REAL* hard
reset - power removal and reapply.

Note that this makes the first probing reset different from all
others.  If the above dvd-ram is hotplugged after ahci is initialized,
no problem occurs because ahci is already fully initialized with phy
powered up.  So, this might also be the reason for other weird AHCI
initial probing abnormalities.

This patch moves power up/down out of port init/deinit and call them
only when needed.

Power down is now called only when suspending.  As system suspend
usually involves powering down 12v for storage devices, this shouldn't
cause problem even if the attached device doesn't support slumber
mode.  However, in partial power management and suspend failure cases,
devices might lock up after suspend attempt.  I thought about removing
transition to slumber mode altogether but ahci spec mandates it before
HBA D3 state transition.  Blacklisting such devices might be the
solution.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      8e16f941
    • T
      [PATCH] libata: prepare ata_sg_clean() for invocation from EH · 70e6ad0c
      由 Tejun Heo 提交于 
      Make ata_sg_clean() global and don't allow NCQ for internal commands.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      70e6ad0c
    • T
      [PATCH] libata: separate out rw ATA taskfile building into ata_build_rw_tf() · bd056d7e
      由 Tejun Heo 提交于 
      Separate out rw ATA taskfile building from ata_scsi_rw_xlat() into
ata_build_rw_tf().  This will be used to improve media error handling.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      bd056d7e
    • T
      [PATCH] libata: implement ata_exec_internal_sg() · 2432697b
      由 Tejun Heo 提交于 
      Sg'ify ata_exec_internal() and call it ata_exec_internal_sg().
Wrapper function around ata_exec_internal_sg() is implemented to
provide ata_exec_internal() interface.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      2432697b
    • T
      [PATCH] libata: make sure IRQ is cleared after ata_bmdma_freeze() · 0f0a3ad3
      由 Tejun Heo 提交于 
      Now that BMDMA status is recorded in irq handler.  ata_bmdma_freeze()
is free to manipulate host status.  Under certain circumstances, some
controllers (ICH7 in enhanced mode w/ IRQ shared) raise IRQ when CTL
register is written to and ATA_NIEN doesn't mask it.

This patch makes ata_bmdma_freeze() clear all pending IRQs after
freezing a port.  This change makes explicit clearing in
ata_device_add() unnecessary and thus kills it.  The removed code was
SFF-specific and was in the wrong place.

Note that ->freeze() handler is always called under ap->lock held and
irq disabled.  Even if CTL manipulation causes stuck IRQ, it's cleared
immediately.  This should be safe (enough) even in SMP environment.
More correct solution is to mask the IRQ from IRQ controller but that
would be an overkill.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      0f0a3ad3
    • T
      [PATCH] libata: move BMDMA host status recording from EH to interrupt handler · ea54763f
      由 Tejun Heo 提交于 
      For certain errors, interrupt handler alter BMDMA host status before
entering EH (clears active and intr).  Thus altered BMDMA host status
value is recorded by BMDMA EH and reported to user.  Move BMDMA host
status recording from EH to interrupt handler.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      ea54763f
    • T
      [PATCH] libata: make sure sdev doesn't go away while rescanning · f84e7e41
      由 Tejun Heo 提交于 
      ata_scsi_dev_rescan() doesn't synchronize against SCSI device detach
and the target sdev might go away in the middle.  Fix it.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      f84e7e41
    • T
      [PATCH] libata: don't request sense if the port is frozen · a569a30d
      由 Tejun Heo 提交于 
      If EH command is issued to a frozen port, it fails with AC_ERR_SYSTEM.
libata used to request sense even when the port is frozen needlessly
adding AC_ERR_SYSTEM to err_mask.  Don't do it.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      a569a30d
    • T
      [PATCH] libata: fix READ CAPACITY simulation · 6a36261e
      由 Tejun Heo 提交于 
      * READ CAPACITY (16) implementation fixed.  Result was shifted by two
  bytes.  Carlos Pardo spotted this problem and submitted preliminary
  patch.  Capacity => 2TB is handled correctly now.  (verifid w/ fake
  capacity)

* Use dev->n_sectors instead of re-reading directly from ID data.

* Define and use ATA_SCSI_RBUF_SET() which considers rbuf length.
  This should be done for all simulation functions.  Userland can
  issue any simulated command with arbitrary buffer length.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Carlos Pardo <Carlos.Pardo@siliconimage.com>
      6a36261e
    • T
      [PATCH] libata: implement ATA_FLAG_SETXFER_POLLING and use it in pata_via, take #2 · 3d3cca37
      由 Tejun Heo 提交于 
      This patch implements ATA_FLAG_SETXFER_POLLING and use in pata_via.
If this flag is set, transfer mode setting performed by polling not by
interrupt.  This should help those controllers which raise interrupt
before the command is actually complete on SETXFER.

Rationale for this approach.

* uses existing facility and relatively simple
* no busy sleep in the interrupt handler
* updating drivers is easy

While at it, kill now unused flag ATA_FLAG_SRST in pata_via.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      3d3cca37
    • T
      [PATCH] libata: set IRQF_SHARED for legacy PCI IDE IRQs · 8070217d
      由 Tejun Heo 提交于 
      There are machines out there which share legacy PCI IDE IRQs w/ other
devices.  libata SFF interrupt/HSM code is ready for shared IRQ and
has been setting IRQF_SHARED for devices in native PCI mode.  Device
in legacy mode is still a PCI device and thus supposedly uses
active-low level triggered IRQ.

Machines with such setup should be quite rare and w/o this flag libata
is likely to fail loading and render the system unuseable.  Also, IDE
driver has been setting IRQF_SHARED for devices in legacy mode for a
looooong time.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      8070217d
    • T
      [PATCH] libata: remove unused HSM_ST_UNKNOWN · 582982e6
      由 Tejun Heo 提交于 
      HSM_ST_UNKNOWN is not used anywhere.  Its value is zero and supposed
to serve sanity check purpose but HSM_ST_IDLE is used for that
purpose.  This unused state causes confusion.  After a port is
initialized but before the first command is executed, the idle hsm
state is UNKNOWN.  However, once a command has completed, the idle hsm
state is IDLE.  This defeats sanity check in ata_pio_task() for the
first command.

This patch removes HSM_ST_UNKNOWN and consequently make HSM_ST_IDLE
the default state.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      582982e6
    • T
      [PATCH] libata: kill unnecessary sht->max_sectors initializations · 2eab80ac
      由 Tejun Heo 提交于 
      sht->max_sectors is overrided unconditionally in ->slave_configure.
There's no reason to set it to any value.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      2eab80ac
    • T
      [PATCH] libata: add missing sht->slave_destroy · c972b60b
      由 Tejun Heo 提交于 
      Add missing sht->slave_destroy.  Most drivers received this fix in
didn't.  Fix those four drives.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      c972b60b
  3. 02 12月, 2006 24 次提交