This allows platforms to specify the rate of the SP804 clocksource via
the clk subsystem.  While ARM boards clock these at 1MHz, BCMRing also
has SP804 timers but are clocked at different rates.
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This allows platforms to specify the clocksource name upon
registration, which is necessary should they wish to register more
than one sp804 clocksource.
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Initialize the clock tree and our sched_clock() early.
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This switches Realview platforms to use the consolidated CLCD panel
support, including the display capabilities.  As Realview uses a PL111,
it can support the full range of pixel formats - 444, 5551, 565 in both
RGB and BGR mode.
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Convert versatile platforms to use the new sched_clock() infrastructure
for extending 32bit counters to full 64-bit nanoseconds.
Tested-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Every architecture using the GIC has a gic_cpu_base_addr pointer for
GIC 0 for their entry assembly code to use to decode the cause of the
current interrupt.  Move this into the common GIC code.
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Tested-by: NAbhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

factorise some generic infrastructure to assist looking up struct clks
for the ARM & SH architecture.

as the code is identical at 99%

put the arch specific code for allocation as example in asm/clkdev.h
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

From: Rob Herring <rob.herring@smooth-stone.com>

The timer-sp h/w used on versatile platforms can also be used for other
platforms, so move it to a common location.
Signed-off-by: NRob Herring <rob.herring@smooth-stone.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

On some platforms, the GPIO value from the gpio_cd pin doesn't need to
be inverted to get it active high.  Add a cd_invert platform data
parameter and change existing platforms using GPIO for CD (only
Realview) to enable it.
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The patch to add the apb_pclk to the AMBA/PrimeCell bus broke
RealView, since the clockdevice is not registered at probe() time.
This moves clock initialization to a core_initcall()

[rmk:moved before the problematical commit to avoid bisect problems]
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The MMC card detection sense has become really confused with negations
at various levels, leading to some platforms not detecting inserted
cards.  Fix this by converting everything to positive logic throughout,
thereby getting rid of these negations.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add a dummy clk definition for the APB pclk signal on all platforms
using the AMBA bus infrastructure.  This ensures that these platforms
continue to work when the core amba bus code controls the APB pclk.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Since we no longer support discontigmem, node is always zero, so
remove this argument.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This adds platform data for the PL022 to the ARM RealView reference
designs, adds the necessary clock definition and fixes a badly
defined IRQ line on the PB1176.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This is a number of basic fixes to the PB1176 that makes it tick
properly:

- Detect MMC insertion/removal even when PL061 GPIO is not compiled
  in. The register to read this status directly is removed on the
  PB1176.
- Define the UART3 on the DevChip (where is actually is) and define
  the new UART4 serial port on the FPGA.
- Also define the clocks for these two UARTs apropriately.
- Remove the false notion that the PB1176 should have its CLCD
  on the ISSP, this is not the case, it is in the DevChip.
- Remove the defintions and the previously commented-out PL081
  DMAC. As confirmed by mail this was found to be broken on the
  PB1176 board and removed from the subsequent FPGA images.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Provide a common sched_clock() implementation for Versatile and
Realview.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The only difference between ICST307 and ICST525 are the two arrays
for calculating the S parameter; the code is now identical.  Merge
the two files and kill the duplicated code.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This makes the ICST support fit more nicely with the clk API,
eliminating the need to *1000 and /1000 in places.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The structures for the ICST307 and ICST525 VCO devices are
identical, so merge them together.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The switch to using GPIOLIB broke the sd/mmc card detection on the
RealView development boards if GPIO_PL061 was not selected.
This patch selects GPIO_PL061 if GPIOLIB is selected.
The sense of the return value from mmc_status has also changed
and is corrected.
Signed-off-by: NColin Tuckley <colin.tuckley@arm.com>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: NTejun Heo <tj@kernel.org>
Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>

Most machine classes want some way to register a block of clk_lookup
structures, and most do it by implementing a clks_register() type
function which walks an array, or by open-coding a loop.

Consolidate all this into clkdev_add_table().
Acked-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: NKevin Hilman <khilman@deeprootsystems.com>
Acked-by: NEric Miao <eric.y.miao@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The RealView PBX board has two 512MB blocks of memory - one at
0x70000000 (with 256MB mirror at 0) and another at 0x20000000. Only the
block at 0x70000000 (or the mirror at 0) may be used for DMA (e.g.
framebuffer). This patch adds the sparsemem definitions to allow the use
of all the memory split as follows:

  256MB @ 0x00000000 (ZONE_DMA)
  512MB @ 0x20000000 (ZONE_NORMAL)
  256MB @ 0x80000000 (ZONE_NORMAL)
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

This patch adds a realview_fixup() function called during booting to set
up the memory banks. This way there is no need to pass a "mem=" argument
on the kernel command line.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

This moves the mmci platform data definition struct away from
arch/arm/include/asm/mach/mmc.h into the more proper place among
the other primecells in include/linux/amba/mmci.h and at the same
time renames it to "mmci.h", and also the struct in this file
confusingly named mmc_platform_data has been renamed
mmci_platform_data for clarity.

Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This removes the totally bogus bus ID:s with two-digit hex numerals
either referring to the base address of corresponding versatile
machine or just some arbitrarily chosen digit in favor of just using
the device identifier as a string. I kept the "dev:" prefix for
DevChips, "fpga:" prefix for FPGA:s and "issp:" prefix for the
other processor bus, just in case someone likes them.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix i2c_board_info definitions - we were defining the 'type' field
of these structures twice since the first argument of I2C_BOARD_INFO
sets this field.  Move the second definition into I2C_BOARD_INFO().
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NBen Dooks <ben-linux@fluff.org>

Add and initialize the gpio_wp and gpio_cd members.  We need to
ensure that all users are covered, because GPIO 0 may be valid.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>

The IRQ_* macros need to be made visible via the mach/irqs.h file but
without the additional macros defined in the board-*.h files.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

If CONFIG_LEDS is enabled, it makes more sense to toggle one LED per CPU
in SMP systems rather than a single LED for all the CPUs.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Having discussed broadcast tick support with Thomas Glexiner, the
broadcast tick devices should be registered with a higher rating
than the global tick device, and it should have the ONESHOT and
PERIODIC feature flags set.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NThomas Glexiner <tglx@linutronix.de>

Pass clocksource pointer to the read() callback for clocksources.  This
allows us to share the callback between multiple instances.

[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Acked-by: NJohn Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>