I stumbled over an old OSA model that claims to support DIAG_ASSIST,
but then rejects the cmd to query its DIAG capabilities.

In the old code this was ok, as the returned raw error code was > 0.
Now that we translate the raw codes to errnos, the "rc < 0" causes us
to fail the initialization of the device.

The fix is trivial: don't bail out when the DIAG query fails. Such an
error is not critical, we can still use the device (with a slightly
reduced set of features).

Fixes: 742d4d40 ("s390/qeth: convert remaining legacy cmd callbacks")
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During vnicc_init wanted_char should be compared to cur_char and not
to QETH_VNICC_DEFAULT. Without this patch there is no way to enforce
the default values as desired values.

Note, that it is expected, that a card comes online with default values.
This patch was tested with private card firmware.

Fixes: caa1f0b1 ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: NAlexandra Winter <wintera@linux.ibm.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Symptom: After vnicc/rx_bcast has been manually set to 0,
	bridge_* sysfs parameters can still be set or written.
Only occurs on HiperSockets, as OSA doesn't support changing rx_bcast.

Vnic characteristics and bridgeport settings are mutually exclusive.
rx_bcast defaults to 1, so manually setting it to 0 should disable
bridge_* parameters.

Instead it makes sense here to check the supported mask. If the card
does not support vnicc at all, bridge commands are always allowed.

Fixes: caa1f0b1 ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: NAlexandra Winter <wintera@linux.ibm.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Symptom: Error message "Configuring the VNIC characteristics failed"
in dmesg whenever an OSA interface on z15 is set online.

The VNIC characteristics get re-programmed when setting a L2 device
online. This follows the selected 'wanted' characteristics - with the
exception that the INVISIBLE characteristic unconditionally gets
switched off.

For devices that don't support INVISIBLE (ie. OSA), the resulting
IO failure raises a noisy error message
("Configuring the VNIC characteristics failed").
For IQD, INVISIBLE is off by default anyways.

So don't unnecessarily special-case the INVISIBLE characteristic, and
thereby suppress the misleading error message on OSA devices.

Fixes: caa1f0b1 ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: NAlexandra Winter <wintera@linux.ibm.com>
Reviewed-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

qeth_l3_dev_hsuid_store() initially checks the card state, but doesn't
take the conf_mutex to ensure that the card stays in this state while
being reconfigured.

Rework the code to take this lock, and drop a redundant state check in a
helper function.

Fixes: b3332930 ("qeth: add support for af_iucv HiperSockets transport")
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

qeth_l?_set_online() goes through a number of initialization steps, and
on any error uses qeth_l?_stop_card() to tear down the residual state.

The first initialization step is qeth_core_hardsetup_card(). When this
fails after having established a QDIO context on the device
(ie. somewhere after qeth_mpc_initialize()), qeth_l?_stop_card() doesn't
shut down this QDIO context again (since the card state hasn't
progressed from DOWN at this stage).

Even worse, we then call qdio_free() as final teardown step to free the
QDIO data structures - while some of them are still hooked into wider
QDIO infrastructure such as the IRQ list. This is inevitably followed by
use-after-frees and other nastyness.

Fix this by unconditionally calling qeth_qdio_clear_card() to shut down
the QDIO context, and also to halt/clear any pending activity on the
various IO channels.
Remove the naive attempt at handling the teardown in
qeth_mpc_initialize(), it clearly doesn't suffice and we're handling it
properly now in the wider teardown code.

Fixes: 4a71df50 ("qeth: new qeth device driver")
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ENOTSUPP is not uapi, use EOPNOTSUPP instead.

Fixes: d66cb37e ("qeth: Add new priority queueing options")
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When managing the promiscuous mode during an RX modeset, qeth caches the
current HW state to avoid repeated programming of the same state on each
modeset.

But while tearing down a device, we forget to clear the cached state. So
when the device is later set online again, the initial RX modeset
doesn't program the promiscuous mode since we believe it is already
enabled.
Fix this by clearing the cached state in the tear-down path.

Note that for the SBP variant of promiscuous mode, this accidentally
works right now because we unconditionally restore the SBP role while
re-initializing.

Fixes: 4a71df50 ("qeth: new qeth device driver")
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: NAlexandra Winter <wintera@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Along with z/VM NICs, there's additional device types that only support
a specific transport mode (eg. external-bridged IQD).
Identify the corresponding error code, and raise a fitting error message
so that the user knows to adjust their device configuration.

On top of that also fix the subsequent error path, so that the rejected
cmd doesn't need to wait for a timeout but gets cancelled straight away.

Fixes: 4a71df50 ("qeth: new qeth device driver")
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().

This patch is generated using following script:

EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"

git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do

	if [[ "$file" =~ $EXCLUDE_FILES ]]; then
		continue
	fi
	sed -i  -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: NPankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.comCo-developed-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NKees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net

The cio layer's intparm logic does not align itself well with how qeth
manages cmd IOs. When an active IO gets terminated via halt/clear, the
corresponding IRQ's intparm does not reflect the cmd buffer but rather
the intparm that was passed to ccw_device_halt() / ccw_device_clear().
This behaviour was recently clarified in
commit b91d9e67 ("s390/cio: fix intparm documentation").

As a result, qeth_irq() currently doesn't cancel a cmd that was
terminated via halt/clear. This primarily causes us to leak
card->read_cmd after the qeth device is removed, since our IO path still
holds a refcount for this cmd.

For qeth this means that we need to keep track of which IO is pending on
a device ('active_cmd'), and use this as the intparm when calling
halt/clear. Otherwise qeth_irq() can't match the subsequent IRQ to its
cmd buffer.
Since we now keep track of the _expected_ intparm, we can also detect
any mismatch; this would constitute a bug somewhere in the lower layers.
In this case cancel the active cmd - we effectively "lost" the IRQ and
should not expect any further notification for this IO.

Fixes: 40554895 ("s390/qeth: add support for dynamically allocated cmds")
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the RX path builds non-linear skbs, the packet headers can
currently spill over into page fragments. Depending on the packet type
and what fields we need to access in the headers, this could cause us
to go past the end of skb->data.

So for non-linear packets, copy precisely the length of the necessary
headers ('linear_len') into skb->data.
And don't copy more, upper-level protocols will peel whatever additional
packet headers they need.

Fixes: 4a71df50 ("qeth: new qeth device driver")
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Depending on a packet's type, the RX path needs to access fields in the
packet headers and thus requires a minimum packet length.
Enforce this length when building the skb.

On the other hand a single runt packet is no reason to drop the whole
RX buffer. So just skip it, and continue processing on the next packet.

Fixes: 4a71df50 ("qeth: new qeth device driver")
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When propagating IO errors back to userspace, one error path in
qeth_irq() currently returns '1' instead of a proper errno.

Fixes: 54daaca7 ("s390/qeth: cancel cmd on early error")
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The L2 bridgeport code uses the coarse 'conf_mutex' for guarding access
to its configuration state.
This can result in a deadlock when qeth_l2_stop_card() - called under the
conf_mutex - blocks on flush_workqueue() to wait for the completion of
pending bridgeport workers. Such workers would also need to aquire
the conf_mutex, stalling indefinitely.

Introduce a lock that specifically guards the bridgeport configuration,
so that the workers no longer need the conf_mutex.
Wrapping qeth_l2_promisc_to_bridge() in this fine-grained lock then also
fixes a theoretical race against a concurrent qeth_bridge_port_role_store()
operation.

Fixes: c0a2e4d1 ("s390/qeth: conclude all event processing before offlining a card")
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: NAlexandra Winter <wintera@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SMCD link group termination is called when peer signals its shutdown
of its corresponding link group. For regular shutdowns no connections
exist anymore. For abnormal shutdowns connections must be killed and
their DMBs must be unregistered immediately. That means the SMCR method
to delay the link group freeing several seconds does not fit.

This patch adds immediate termination of a link group and its SMCD
connections and makes sure all SMCD link group related cleanup steps
are finished.
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Given the way how the sysfs attributes are registered / unregistered,
the show/store helpers will never be called with a NULL drvdata.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The remaining usage effectively is a kmemdup() of the query object.
By not wrapping it, some of the callers can now use GFP_KERNEL for the
allocation.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use vlan_for_each() instead of tracking each registered VID internally.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current code processes each (VLAN) device twice - once to inspect the
IPv4 mcast addresses, and then a second time to walk the IPv6 mcast
addresses. Unify all this into a single helper, thus removing some
checks and a duplicated VLAN lookup.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Trust the IPv4/IPv6 code to properly remove its mcast addresses when a
VLAN device is unregistered, and then also trigger an RX modeset
whenever it's needed.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Push the inet6_dev locking down into the helper that actually needs it
for walking the mc_list.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

qeth_core_free_card() is meant to be the counterpart of
qeth_alloc_card() - but unfortunately was also picked as the place
to free the QDIO queues.

This gets messy when qeth_core_probe_device() fails during
qeth_add_dbf_entry(). At this point the card->qdio.state is not initialized
yet, so qeth_free_qdio_queues() ends up operating on uninitialized data.

Luckily for now, the whole qeth_card struct is zero-allocated and the value
of the QETH_QDIO_UNINITIALIZED enum is 0 as well. So there's no real impact
from this bug at the moment, it's just really fragile.

Clean this up by moving the qeth_free_qdio_queues() call up one level in
the hierarchy. This way it doesn't get called from the error path.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When current code fails to allocate an skb in the RX path, it drops the
whole RX buffer. Considering the large number of packets that a single
RX buffer might contain, this is quite drastic.

Skip over the packet instead, and try to extract the next packet from
the RX buffer.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Packets with an unexpected HW format are currently first extracted from
the RX buffer, passed upwards to the layer-specific driver and only then
finally dropped.

Enhance the RX path so that we can drop such packets before even
allocating an skb. For this, add some additional logic so that when a
packet is meant to be dropped, we can still walk along the packet's data
chunks in the RX buffer. This allows us to extract the following
packet(s) from the buffer.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Each RX buffer may contain up to 64KB worth of data. In case the device
needs to discard a packet _after_ already having reserved space for it
in the buffer, the whole buffer gets set to ERROR state. As the buffer
might contain any number of good packets, this can result in collateral
packet loss.

qeth can provide relief by enabling per-frame invalidation. The RX
buffer is then presented as usual, we just need to spot & drop any
individual packet that was flagged as invalid.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Where available, use the fine-grained counters in rtnl_link_stats64 to
indicate different RX error causes. For drop reasons, use driver-private
ethtool counters.

In particular this patch allows us to keep track of driver-side drops due
to unknown/unsupported HW descriptor format.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of storing the multicast-mapped MAC address in an IP address
object, just calculate the MAC address when actually building a cmd
for the IP address.

While at it, also clean up some rather verbose copying of IP addresses.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace our custom implementations with the stack's version of IP address
hashing.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Any change to the card state should only be driven by
qeth_l?_set_online() and qeth_l?_stop_card().

qeth_qdio_clear_card() currently also gets called from
(a) qeth_core_shutdown(), where we haven't walked through the whole
    teardown sequence. So changing the state to DOWN is not accurate.
(b) qeth_core_hardsetup_card(), which is only called while the card is
    still in DOWN state. No change in behaviour here.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When setting a device online, both subdrivers have the same code to
program the HW trap and Isolation mode. Move that code into a single
place.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When napi_complete_done() returns false, the NAPI instance is still
active and we can keep the IRQ disabled a little longer.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

qdio.h recently gained a new helper macro that handles wrap-around on a
QDIO queue, consistently use it across all of qeth.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For IQD devices with Multi-Write support, we can defer the queue-flush
further and transmit multiple IO buffers with a single TX doorbell.
The same-target restriction still applies.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: NAlexandra Winter <wintera@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Put the Sniffer bit next to all the other CHSC AC2 bits.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: NSteffen Maier <maier@linux.ibm.com>
Signed-off-by: NVasily Gorbik <gor@linux.ibm.com>

Without this patch, a command bit in the supported commands mask is only
ever set to unsupported during set online. If a command is ever marked as
unsupported (e.g. because of error during qeth_l2_vnicc_query_cmds),
subsequent successful initialization (offline/online) would not bring it
back.

Fixes: caa1f0b1 ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: NAlexandra Winter <wintera@linux.ibm.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Smatch discovered the use of uninitialized variable sup_cmds
in error paths.

Fixes: caa1f0b1 ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: NAlexandra Winter <wintera@linux.ibm.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

The QIB parm area is 128 bytes long. Current code consistently misuses
an _entirely unrelated_ QDIO constant, merely because it has the same
value. Stop doing so.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: NBenjamin Block <bblock@linux.ibm.com>
Reviewed-by: NJens Remus <jremus@linux.ibm.com>
Signed-off-by: NVasily Gorbik <gor@linux.ibm.com>

The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IQD devices offer limited support for bulking: all frames in a TX buffer
need to have the same target. qeth_iqd_may_bulk() implements this
constraint, and allows us to defer the TX doorbell until
(a) the buffer is full (since each buffer needs its own doorbell), or
(b) the entire TX queue is full, or
(b) we reached the BQL limit.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>