APEI firmware first mode must be turned on explicitly on some
machines, otherwise there may be no GHES hardware error record for
hardware error notification.  APEI bit in generic _OSC call can be
used to do that, but on some machine, a special WHEA _OSC call must be
used.  This patch adds the support to that WHEA _OSC call.
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Reviewed-by: NAndi Kleen <ak@linux.intel.com>
Reviewed-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

In APEI firmware first mode, hardware error is reported by hardware to
firmware firstly, then firmware reports the error to Linux in a GHES
error record via POLL/SCI/IRQ/NMI etc.

This may result in some issues if OS has no full APEI support.  So
some firmware implementation will work in a back-compatible mode by
default.  Where firmware will only notify OS in old-fashion, without
GHES record.  For example, for a fatal hardware error, only NMI is
signaled, no GHES record.

To gain full APEI power on these machines, APEI bit in generic _OSC
call can be specified to tell firmware that Linux has full APEI
support.  This patch adds the APEI bit support in generic _OSC call.
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Reviewed-by: NAndi Kleen <ak@linux.intel.com>
Reviewed-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Some machine may have broken firmware so that GHES and firmware first
mode should be disabled.  This patch adds support to that.
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Reviewed-by: NAndi Kleen <ak@linux.intel.com>
Reviewed-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

GHES (Generic Hardware Error Source) is used to process hardware error
notification in firmware first mode.  But because firmware first mode
can be turned on but can not be turned off, it is unreasonable to
unload the GHES module with firmware first mode turned on.  To avoid
confusion, this patch makes GHES can be enabled/disabled in
configuration time, but not built as module and unloaded at run time.
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Reviewed-by: NAndi Kleen <ak@linux.intel.com>
Reviewed-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

This patch changes APEI EINJ and ERST to use apei_exec_run for
mandatory actions, and apei_exec_run_optional for optional actions.

Cc: Thomas Renninger <trenn@novell.com>
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Some actions in APEI ERST and EINJ tables are optional, for example,
ACPI_EINJ_BEGIN_OPERATION action is used to do some preparation for
error injection, and firmware may choose to do nothing here.  While
some other actions are mandatory, for example, firmware must provide
ACPI_EINJ_GET_ERROR_TYPE implementation.

Original implementation treats all actions as optional (that is, can
have no instructions), that may cause issue if firmware does not
provide some mandatory actions.  To fix this, this patch adds
apei_exec_run_optional, which should be used for optional actions.
The original apei_exec_run should be used for mandatory actions.

Cc: Thomas Renninger <trenn@novell.com>
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

printk is used by GHES to report hardware errors.  Normally, the
printk will be ratelimited to avoid too many hardware error reports in
kernel log.  Because there may be thousands or even millions of
corrected hardware errors during system running.

That is different for fatal hardware error, because system will go
panic as soon as possible, there will be no more than several error
records.  And these error records are valuable for system fault
diagnosis, so they should not be ratelimited.
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

When we debug ERST table with erst-dbg, if the error record in ERST
table is too long(>4K), it can't be read out.  So this patch increases
the buffer size to 16K to ensure such error records can be read from
ERST table.
Signed-off-by: NChen Gong <gong.chen@linux.intel.com>
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

erst_dbg module can not work when ERST is disabled.  So disable module
loading to provide clearer information to user.
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

The firmware on some machine will report duplicated hardware error
source ID in HEST.  This is considered a firmware bug.  To provide
better warning message, this patch adds duplicated hardware error
source ID detecting and corresponding printk.

This patch fixes #37412 on kernel bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=37412

Reported-by: marconifabio@ubuntu-it.org
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Tested-by: NMathias <janedo.spam@gmail.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

...which is measured by the size and not the amount of space remaining.

Waiting upon size-8, did one of two things. In the common case with more
than 8 bytes available to write into the ring, it would return
immediately. Otherwise, it would timeout given the impossible condition
of waiting for more space than is available in the ring, leading to
warnings such as:

[drm:intel_cleanup_ring_buffer] *ERROR* failed to quiesce render ring
whilst cleaning up: -16
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NKeith Packard <keithp@keithp.com>

This reverts commit a51f7a66.

We still have a few Ironlake and Sandybridge machines which fail when
RC6 is enabled. Better luck next release?
Signed-off-by: NKeith Packard <keithp@keithp.com>

i915_driver_load adds a write-combining MTRR region for the GTT
aperture to improve memory speeds through the aperture. If
i915_driver_load fails after this, it would not have cleaned up the
MTRR. This shouldn't cause any problems, except for consuming an MTRR
register. Still, it's best to clean up completely in the failure path,
which is easily done by calling mtrr_del if the mtrr was successfully
allocated.

i915_driver_load calls i915_gem_load which register
i915_gem_inactive_shrink. If i915_driver_load fails after calling
i915_gem_load, the shrinker will be left registered. When called, it
will access freed memory and crash. The fix is to unregister the shrinker in the
failure path using code duplicated from i915_driver_unload.

i915_driver_load also has some incorrect gotos in the error cleanup
paths:

 * After failing to initialize the GTT (which cannot happen, btw,
   intel_gtt_get returns a fixed (non-NULL) value), it tries to
   free the uninitialized WC IO mapping. Fixed this by changing the
   target from out_iomapfree to out_rmmap
Signed-off-by: NKeith Packard <keithp@keithp.com>
Tested-by: NLin Ming <ming.m.lin@intel.com>

The macro MIN_MEMORY_BLOCK_SIZE is currently defined twice in two .c
files, and I need it in a third one to fix a powerpc bug, so let's
first move it into a header
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NIngo Molnar <mingo@elte.hu>

Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

[  191.310008] WARNING: kmemcheck: Caught 32-bit read from freed memory (f0d25f14)
[  191.310011] c056d2f088000000105fd2f00000000050415353040000000000000000000000
[  191.310020]  i i i i f f f f f f f f f f f f f f f f f f f f f f f f f f f f
[  191.310027]                                          ^
[  191.310029]
[  191.310032] Pid: 737, comm: modprobe Not tainted 3.0.0-rc5+ #268 Hewlett-Packard HP Compaq 6005 Pro SFF PC/3047h
[  191.310036] EIP: 0060:[<f80b3104>] EFLAGS: 00010286 CPU: 0
[  191.310039] EIP is at hp_wmi_perform_query+0x104/0x150 [hp_wmi]
[  191.310041] EAX: f0d25601 EBX: f0d25f00 ECX: 000121cf EDX: 000121ce
[  191.310043] ESI: f0d25f10 EDI: f0f97ea8 EBP: f0f97ec4 ESP: c173f34c
[  191.310045]  DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[  191.310046] CR0: 8005003b CR2: f540c000 CR3: 30f30000 CR4: 000006d0
[  191.310048] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[  191.310050] DR6: ffff4ff0 DR7: 00000400
[  191.310051]  [<f80b317b>] hp_wmi_dock_state+0x2b/0x40 [hp_wmi]
[  191.310054]  [<f80b6093>] hp_wmi_init+0x93/0x1a8 [hp_wmi]
[  191.310057]  [<c10011f0>] do_one_initcall+0x30/0x170
[  191.310061]  [<c107ab9f>] sys_init_module+0xef/0x1a60
[  191.310064]  [<c149f998>] sysenter_do_call+0x12/0x28
[  191.310067]  [<ffffffff>] 0xffffffff
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

Using buffer->output[1] without mutex_lock()
Signed-off-by: NJose Alonso <joalonsof@gmail.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

This reverts commit a3d77411,

as it causes a mess in the wireless rfkill status on some models.
It is probably a bad idea to toggle the rfkill for all dell models
without the respect to the claim that it is hardware-controlled.

Cc: stable@kernel.org
Signed-off-by: NKeng-Yu Lin <kengyu@canonical.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

Patch 2e711c04
(PM: Remove sysdev suspend, resume and shutdown operations)
deleted sysdev_suspend(), which was being relied on to call
check_wakeup_irqs() in suspend.  If check_wakeup_irqs() is not
called, wake interrupts that are pending when suspend is
entered may be lost.  It also breaks IRQCHIP_MASK_ON_SUSPEND,
which is handled in check_wakeup_irqs().

This patch adds a call to check_wakeup_irqs() in syscore_suspend(),
similar to what was deleted in sysdev_suspend().
Signed-off-by: NColin Cross <ccross@android.com>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Acked-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

I came across a memory leak during a cyclic cpu-online-offline test.
Signed-off-by: NYu Luming <luming.yu@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDave Jones <davej@redhat.com>

It is possible that a PMBus device supports the READ_TEMPERATURE2 and/or
READ_TEMPERATURE3 registers but does not support READ_TEMPERATURE1.
Improve temperature status register detection to address this condition.
Reported-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.39+

Negative temperatures were returned in degrees C instead of milli-Degrees C.
Also, negative temperatures were reported for remote temperature sensors even
if the chip was configured for positive-only results.

Fix by detecting temperature modes, and by treating negative temperatures
similar to positive temperatures, with appropriate sign extension.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.30+

When firewire-ohci is bound to a Pinnacle MovieBoard, eventually a
"Register access failure" is logged and an interrupt storm or a kernel
panic happens.  https://bugzilla.kernel.org/show_bug.cgi?id=36622

Until this is sorted out (if that is going to succeed at all), let's
just prevent firewire-ohci from touching these devices.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Cc: <stable@kernel.org>

This driver handles the variants pca9530-pca9533, so it chose the name
"pca953x".  However, there is a gpio driver which decided on the same
name.  As a result, those two can't be loaded at the same time.  Add a
subsystem prefix to make the driver name unique.  Device matching will not
suffer, because both are I2C drivers which match using a
i2c_device_id-table which is not altered.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NJean Delvare <khali@linux-fr.org>
Cc: Richard Purdie <richard.purdie@linuxfoundation.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This fixes a regression in 3.0 reported by Paul Parsons regarding the
removal of the msleep(1) in the ds1wm_reset() function:

: The linux-3.0-rc4 DS1WM 1-wire driver is logging "bus error, retrying"
: error messages on an HP iPAQ hx4700 PDA (XScale-PXA270):
:
: <snip>
: Driver for 1-wire Dallas network protocol.
: DS1WM w1 busmaster driver - (c) 2004 Szabolcs Gyurko
: 1-Wire driver for the DS2760 battery monitor  chip  - (c) 2004-2005, Szabolcs Gyurko
: ds1wm ds1wm: pass: 1 bus error, retrying
: ds1wm ds1wm: pass: 2 bus error, retrying
: ds1wm ds1wm: pass: 3 bus error, retrying
: ds1wm ds1wm: pass: 4 bus error, retrying
: ds1wm ds1wm: pass: 5 bus error, retrying
: ...
:
: The visible result is that the battery charging LED is erratic; sometimes
: it works, mostly it doesn't.
:
: The linux-2.6.39 DS1WM 1-wire driver worked OK.  I haven't tried 3.0-rc1,
: 3.0-rc2, or 3.0-rc3.

This sleep should not be required on normal circuitry provided the
pull-ups on the bus are correctly adapted to the slaves.  Unfortunately,
this is not always the case.  The sleep is restored but as a parameter to
the probe function in the pdata.

[akpm@linux-foundation.org: coding-style fixes]
Reported-by: NPaul Parsons <lost.distance@yahoo.com>
Tested-by: NPaul Parsons <lost.distance@yahoo.com>
Signed-off-by: NJean-François Dagenais <dagenaisj@sonatest.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The LM95241 driver accepts every chip ID equal to or larger than 0xA4 as its
own, and other chips such as LM95245 use chip IDs in the accepted ID range.
This results in false chip detection.

Fix problem by accepting only the known LM95241 chip ID.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.30+

    
Multiple attempts to dynamically reallocate pci resources have
unfortunately lead to regressions. Though we continue to fix the
regressions and fine tune the dynamic-reallocation behavior, we have not
reached a acceptable state yet.
    
This patch provides a interim solution. It disables dynamic reallocation
by default, but adds the ability to enable it through pci=realloc kernel
command line parameter.
Tested-by: NOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NRam Pai <linuxram@us.ibm.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The ramp_delay variable can be set lower than the desired value.
This patch fixes it.
Signed-off-by: NDonggeun Kim <dg77.kim@samsung.com>
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NKyungMin Park <kyungmin.park@samsung.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Small cleanups for better readability.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The platform_data (pdata) may be pointing to __initdata section, which
may be free'd from the memory. The dependency on pdata in non-init
functions is removed in this patch to allow platform to declare
__initdata for platform data.
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Currently, ramp_delay variable is used uninitialzed in
max8997_set_voltage_ldobuck which gets called through
regulator_register calls.

To fix the problem, in max8997_pmic_probe, ramp_delay initialization
code is moved before calls to regulator_register.

Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Acked-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NJonghwan Choi <jhbird.choi@samsung.com>
Acked-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

evergreen+ asics have 2-6 crtcs.  Don't access crtc registers
for crtc regs that don't exist as they have very high latency
and may cause problems on some asics.  The previous code missed
a few cases and was not fine grained enough (missed the 4 crtc
case for example).

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=38800

v2: fix typo noticed by Chris Bandy <cbandy@jbandy.com>
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Reviewed-by: NMichel Dänzer <michel@daenzer.net>
Tested-by: NSimon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The wrong bit was masked when acking langwell gpio interrupts.

Reason for maskig the wrong bit was probably because__ffs() and ffs() functions
return bit indexes differently (0..31 vs 1..32)

This fixes langwell based devices from hanging when a gpio interrupt is
triggered and undoes the breakage which occurred in change set
732063b9Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

According to the hardware documentation, GDRST is exactly the same as on
Sandybridge.  So simply enable the existing code.
Signed-off-by: NKenneth Graunke <kenneth@whitecape.org>
Signed-off-by: NKeith Packard <keithp@keithp.com>

On sinks with a DPCD rev of 1.1 or greater, we can send sink power
management commands to address 0x600 per section 5.1.5 of the
DisplayPort 1.1a spec.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NKeith Packard <keithp@keithp.com>
Signed-off-by: NKeith Packard <keithp@keithp.com>

When checking link status during a hot plug event or detecting sink
presence, we need to retry 3 times per the spec (section 9.1 of the 1.1a
DisplayPort spec).  Consolidate the retry code into a
native_aux_read_retry function for use by get_link_status and _detect.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NKeith Packard <keithp@keithp.com>
Signed-off-by: NKeith Packard <keithp@keithp.com>

We currently use this when a hot plug event is received, only checking
the link status and re-training if we had previously configured a link.
However if we want to preserve the DP configuration across both hot plug
and DPMS events (which we do for userspace apps that don't respond to
hot plug uevents), we need to unconditionally check the link and try to
bring it up on hot plug.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NKeith Packard <keithp@keithp.com>
Signed-off-by: NKeith Packard <keithp@keithp.com>

If ->detect is called too soon after a hot plug event, the sink may not
be ready yet.  So try up to 3 times with 1ms sleeps in between tries to
get the data (spec dictates that receivers must be ready to respond within
1ms and that sources should try 3 times).

See section 9.1 of the 1.1a DisplayPort spec.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NKeith Packard <keithp@keithp.com>
Signed-off-by: NKeith Packard <keithp@keithp.com>