The flags may have to be overwritten, so add them to the CAT25_INFO
macro.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

of_property_read_bool properly compiles away, no need to ifdef this
for non DT builds.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

For SPI NOR flash that are larger than 128Mbit (16MiB), we need 4 bytes
of address space to reach the entire flash; however, the original SPI
flash protocol used only 3 bytes for the address. So far, the practice
for handling this has been either to use new command opcodes that are
defined to use 4 bytes for their address, or to use special
mode-switching command to configure all traditionally-3-byte-address
commands to take 4 bytes instead.

Macronix and Spansion developed two incompatible methods for
entering/exiting "4-byte address mode." Micron flash uses the Macronix
method (OPCODE_{EN4B,EX4B}), not the Spansion method.

This patch solves addressing issues on Micron n25q256a and provides the
ability to support other future Micron SPI flash >16MiB.

Quoting a Micron representative:

  "Majority of our NOR that needs 4-byte addressing (256Mb or 32MB and
   higher) enter and exit 4byte through B7h and E9h commands. The
   N25Q256A7xxx and N25Q512A7xxx parts do not support 4-byte addressing
   mode via B7h or E9h command."

They further clarified that those that don't support the enter/exit
opcodes (B7h/E9h) are manufactured specifically to come up by default in
4-byte mode. We don't need to treat those parts any diffently, as they
will discard the EN4B opcode as a no-op.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Acked-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Added a 16MiB winbond devce to the device list
erase size = 64KiB and number of blocks = 256.
Signed-off-by: NGirish K S <ks.giri@samsung.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Traditionally, the command set used by SPI flash only supported a 3-byte
address. However, large SPI flash (>= 32MiB, or 256Mib) require 4 bytes
to address the entire flash. Most manufacturers have supplied a mode
switch (via a "bank register writer", or a "enable 4-byte mode"
command), which tells the flash to expect 4 address cycles from now on,
instead of 3. This mode remains until power is cut, the reset line is
triggered (on packages where present), or a command is sent to reset the
flash or to reset the 3-byte addressing mode.

As an alternative, some flash manufacturers have developed a new command
set that accept a full 4-byte address. They can be used orthogonally to
any of the modes; that is, they can be used when the flash is in either
3-byte or 4-byte address mode.

Now, there are a number of reasons why the "stateful" 4-byte address
mode switch may not be acceptable. For instance, some SoC's perform a
dumb boot sequence in which they only send 3-byte read commands to the
flash. However, if an unexpected reset occurs, the flash chip cannot be
guaranteed to return to its 3-byte mode. Thus, the SoC controller and
flash will not understand each other. (One might consider hooking up the
aforementioned reset pin to the system reset line so that any system
reset will reset the flash to 3-byte mode, but some packages do not
provide this pin. And in some other packages, one must choose between
having a reset pin and having enough pins for 4-output QSPI support.
It is an error prone process choosing a flash that will support a
hardware reset pin!)

This patch provides support for the new stateless command set, so that
we can avoid the problems that come with a stateful addressing mode
change. The flash can be left in "3-byte mode" while still accessing the
entire flash.

Note that Spansion supports this command set on all its large flash
(e.g, S25FL512S), and Macronix has begun supporting this command set on
some new flash (e.g., MX25L25635F). For the moment, I don't know how to
differentiate the Macronix that don't support this command set (e.g.,
MX25L25635E) from those that do, so this patch only supports Spansion.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Acked-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This device was reported over a year ago on OpenWrt mailing list in the
thread [OpenWrt-Devel] RedBoot partition table with winbond m25q128vb
(unfortunately, I can't find message id). Macpaul seemed to have
problems with partition driver, but it seems the device was working OK.
Reported-by: NMacpaul Lin <macpaul@gmail.com>
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NKrzysztof Mazur <krzysiek@podlesie.net>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Not all SST devices implement the SST byte programming command.
Some devices (like SST25VF064C) implement only standard m25p80 page
write command.

Now SPI flash devices that need sst_write() are explicitly marked
with new SST_WRITE flag and the decision to use sst_write() is based
on this flag instead of manufacturer id.
Signed-off-by: NKrzysztof Mazur <krzysiek@podlesie.net>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NDaniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NDaniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Add support for GigaDevice GD25Q32 32 Mbit (4 MB) SPI Flash (see datasheet:
http://www.gigadevice.com/UserFiles/GD25Q32_Rev0.2(1).pdf) used in Hame MPR-A1
and clones, and for GigaDevice GD25Q64 64 Mbit (8 MB) SPI Flash used in
Hame MPR-A2 devices (datasheet: http://www.gigadevice.com/UserFiles/GD25Q64.pdf).
Signed-off-by: NMichel Stempin <michel.stempin@wanadoo.fr>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

This patch adds generic support for flash protection on STmicro chips.
On chips with less than 3 protection bits, the unused bits are don't cares
and so can be written anyway. The lock function will only change the
protection bits if it would not unlock other areas. Similarly, the unlock
function will not lock currently unlocked areas. Tested on the m25p64.
Signed-off-by: NAustin Boyle <Austin.Boyle@aviatnet.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

Micron N25Q128 has two types of flash:

 - One is for 1.8v supply voltage, prefixed with "n25q128a11" and the jedec
   code is 0x20bb18.

 - Another is for 3v supply voltage, prefixed with "n25q128a13" and the jedec
   code is 0x20ba18.

So modify the original type info and add another type for Micron N25Q128.
Signed-off-by: NLiming Wang <walimisdev@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

Signed-off-by: NMatthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

Add DT property "m25p,fast-read" that signalises the particular
chip supports "fast read" opcode.
Signed-off-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

Quoting from the datasheet for S25FL064P, rev. 05, Nov 18 2011, § 9.17:

"A 64 kB[sic] sector erase (D8h) command issued on 4 kB or 8 kB erase
sectors will erase all sectors in the specified 64 kB region. However,
please note that a 4 kB sector erase (20h) or 8 kB sector erase (40h)
command will not work on a 64 kB sector."

Referring further to Table 8.1 and Table 8.2, it is clearly seen
that most of the sectors are 64KiB; therefore disable this 4KiB
erase support since it's valid only on first/last sectors.
Signed-off-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NJan Luebbe <jlu@pengutronix.de>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The manufacturer datasheet can be found on the Micron website,
under the name n25q_256mb_3v_65nm.pdf:

http://www.micron.com/search?source=ps&q=n25q_256mb_3v_65nmSigned-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Due to the implementation of the following loop at the end
of jedec_probe():

776         for (tmp = 0; tmp < ARRAY_SIZE(m25p_ids) - 1; tmp++) {
777                 info = (void *)m25p_ids[tmp].driver_data;
778                 if (info->jedec_id == jedec) {
779                         if (info->ext_id != 0 && info->ext_id != ext_jedec)
780                                 continue;
781                         return &m25p_ids[tmp];
782                 }
783         }

In particular line 779 in the above numbering, the chips with ext_id != 0 must
be ordered first in the list of chips (m25p_ids[]).
Signed-off-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NKnut Wohlrab <knut.wohlrab@de.bosch.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NChunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NAlexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NAlexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Adds JEDEC ID for the 1.8V version of WinBond w25q32.
Signed-off-by: NFederico Fuga <fuga@studiofuga.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Winbond W25Q80BW is a 8Mbit serial flash memory device.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Add the id and sector mappings for mx25l2005a flash chips.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This chip isn't JEDEC-compatible.
Signed-off-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

In many places in drivers we verify for the zero length, but this is very
inconsistent across drivers. This is obviously the right thing to do, though.
This patch moves the check to the MTD API functions instead and removes a lot
of duplication.
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Reviewed-by: NShmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The MTD API function now zero the 'retlen' parameter before calling
the driver's method — do not do this again in drivers. This removes
duplicated '*retlen = 0' assignent from the following methods:

    'mtd_point()'
    'mtd_read()'
    'mtd_write()'
    'mtd_writev()'
    'mtd_panic_write()'
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

We already verify that offset and length are within the MTD device size
in the MTD API functions. Let's remove the duplicated checks in drivers.
This patch only affects the following API's:

'mtd_erase()'
'mtd_point()'
'mtd_unpoint()'
'mtd_get_unmapped_area()'
'mtd_read()'
'mtd_write()'
'mtd_panic_write()'
'mtd_lock()'
'mtd_unlock()'
'mtd_is_locked()'
'mtd_block_isbad()'
'mtd_block_markbad()'

This patch adds a bit of noise by removing too sparse empty lines, but this is
not too bad.
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>