Add a flag that enables match found notification to align with
FW API change.

Cc: <stable@vger.kernel.org> [3.17+]
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When tid_tspec was set to IWL_TID_NON_QOS (8) this led to an
out of bounds access to the tid_to_mac80211_ac array whose size
is 7. Fix this.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

commit 5c904224
"iwlwifi: mvm: don't allow diversity if BT Coex / TT forbid it"
broke Rx with 2 chains for diversity.
This had an impact on throughput where we're using only a single
stream (11a/b/g APs, single stream APs, static SMPS).

Fixes: 5c904224 ("iwlwifi: mvm: don't allow diversity if BT Coex / TT forbid it")
Cc: Stable <stable@vger.kernel.org>  [3.16+]
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We were advertising iwlwifi-7265-X.ucode instead of
iwlwifi-7265D-X.ucode. Fix this.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The trans cfg was not replaced for 7265-D cards. This led to a check of
the min-NVM version against a 7265-C card, causing very-old 7265-D cards
to operate incorrectly with the driver.

Fixes: 3fd0d3c1 ("iwlwifi: pcie: support 7265-D devices")
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

New FW has chunks that are larger than the size limit of the
FH's DMA. To make sure we don't crash it - actively limit the
max size of each chunk.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

A few device IDs were added, reflect this change in the
driver.

Cc; <stable@vger.kernel.org> [3.13+]
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In the very unlikely case in which no firmware could be,
found. the same pointer was freed twice. Fix that.

Fixes: 490fefeb ("iwlwifi: define the .ucode file format for debug")
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When we reset the device, the CSR_INT gets cleared as well
as CSR_INT_MASK. Meaning that we shouldn't get any interrupt
but, due to a hardware bug, recent devices will keep sending
interrupts. This leads to an interrupt storm while stopping
the device.
The way to fix this is to ACK all the interrupts after the
device is reset so that the value of CSR_INT will stay
0xffffffff.

Fixes: 522713c8 ("iwlwifi: pcie: properly reset the device")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

On stop(), we already cleared our internal state,
and the restart_complete() callback won't be
called, so simply clear the IN_HW_RESTART flag.

Keeping the flag might result in invalid state
on the next start(), preventing the driver starting
properly.

Additionally, don't take IWL_MVM_REF_UCODE_DOWN on stop()
if hw restart was requested, as the ref was already
taken in this case.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The new ucode package format holds also the usniffer images
(in addition to the operational images and the TLVs).
The driver can load the usniffer image if debug
configuration tells it to.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Until this patch, dumping the monitor data could be done only
for PCIe external (DRAM) mode in 7000 HW family. This patch
allows to pull the monitor data also on other families, and
also to pull the monitor data if an internal buffer is used.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Sometimes there is a need to configure some registers for
setting some FW properties, such as the FW monitor mode
(internal/external). This patch supports setting this for
PCIe mode.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Send all debug-configuration HCMDs that are set in the TLVs
to the FW. This may include HCMDs to configure the FW
monitor and FW log level, for example.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Debug information can be appended to the firmware file. This
information will be used by the driver to enable / disable
debugging features in the firmware.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Interoperability issues were identified and root caused to
the Smart Fifo watermarks. These issues arose with
NetGear R7000. Fix this.

Cc: <stable@vger.kernel.org> [3.14+]
Fixes: 1f3b0ff8 ("iwlwifi: mvm: Add Smart FIFO support")
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Since the commit below, iwldvm sends the FLUSH command to
the firmware. All the devices that use iwldvm have a
firmware that expects the _v3 version of this command,
besides 5150.
5150's latest available firmware still expects a _v2 version
of the FLUSH command.
This means that since the commit below, we had a mismatch for
this specific device only.
This mismatch led to the NMI below:

Loaded firmware version: 8.24.2.2
Start IWL Error Log Dump:
Status: 0x0000004C, count: 5
0x00000004 | NMI_INTERRUPT_WDG
0x000006F4 | uPc
0x000005BA | branchlink1
0x000006F8 | branchlink2
0x000008C2 | interruptlink1
0x00005B02 | interruptlink2
0x00000002 | data1
0x07030000 | data2
0x00000068 | line
0x3E80510C | beacon time
0x728A0EF4 | tsf low
0x0000002A | tsf hi
0x00000000 | time gp1
0x01BDC977 | time gp2
0x00000000 | time gp3
0x00010818 | uCode version
0x00000000 | hw version
0x00484704 | board version
0x00000002 | hcmd
0x2FF23080 | isr0
0x0103E000 | isr1
0x0000001A | isr2
0x1443FCC3 | isr3
0x11800112 | isr4
0x00000068 | isr_pref
0x000000D4 | wait_event
0x00000000 | l2p_control
0x00000007 | l2p_duration
0x00103040 | l2p_mhvalid
0x00000007 | l2p_addr_match
0x00000000 | lmpm_pmg_sel
0x00000000 | timestamp
0x00000200 | flow_handler

This was reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=88961

Cc: <stable@vger.kernel.org>
Fixes: a0855054 ("iwlwifi: dvm: drop non VO frames when flushing")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In 8000 B-step the FW file has changed, but by the time we
know the HW step, the FW file is already requested.

This patch defaults 8000 family to B-step if no HW step is
detected in time. When it can it checks what HW step it
really is (in 8000 family) and if it isn't B-step, the FW
file is released and the A-step file is requested.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Fix the 4165 series name that was called 4265 by mistake.
Signed-off-by: NOren Givon <oren.givon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Adds all FH registers between FH_MEM_UPPER_BOUND and
FH_MEM_LOWER_BOUND (which should be readable to the driver)
to the dump data when it is collected.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The ucode load flow changed for B0 hardware step.
Change the code accordingly.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Not doing so would allow other possible users of the device
to take ownership and prevent normal WiFi operation.

This fixes the second part of:
https://bugzilla.kernel.org/show_bug.cgi?id=87191Reviewed-by: NMoshe Harel <moshe.harel@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

7265D are new devices that should always have a new NVM
(at least 0x0c11). The firmware has issues with older
versions of the NVM which are not and will not be available
to the common mortals.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Handle NVM file header. When NVM header detected, skip
the header and reading only the sections data.
Signed-off-by: NIdan Kahlon <idanx.kahlon@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add the channels on which there was a match for every match reported
by the firmware.  The firmware reports the channels as indices to the
array of channels that was passed in the scheduled scan request, so we
need to save the array when entering D3 to make sure it is available
when we resume.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add SSID information to the net-detect indication to userspace.  Fetch
the matched profiles from the firmware in order to find the correct
SSIDs in the profiles that matched.

Since the net-detect information is stored in cfg80211, and in theory
it could change while we are waking up and reading the matched
profiles, we need to save it when we enter D3 so it is available
during resume.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

A following patche will use trans_pcie->cmd_in_flight
for reference accounting as well. get ready for it.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

IWL_MVM_REF_PROTECT_CSA is missing from the ref strings
used by debugfs.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This impacts the partition between BT and Wifi.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares have this TLV flag set.
Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares have this TLV flag set.
Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This TLV flag is set for all the supported firmwares.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This firmware is not supported anymore.
Stop loading this firmware - and remove the code that
handled older versions.
Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Query the firmware for scan offload matches when waking up in order to
report net detect as the reason for the wake up.

This requires a new command API to be implemented.  Additionally,
remove some net detect command entries that are not valid anymore.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware file-format is described in iwl-fw-file.h, while the
internal handling structures and functions are in iwl-fw.h.

Fix the separation between the files by moving file format
definitions to iwl-fw-file.h.

Also add a missing description for a kernel-doc member, and it's
not needed to include iwl-fw-file.h again from the code (thanks
to Liad Kaufman).
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Also update the timeout for the data verification.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add a new SDIO card id intended for the new 4165 series.
Signed-off-by: NOren Givon <oren.givon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In case of channel switch, we need to teardown the TDLS peers.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>