dw_mci_of_find_slot_node() is only used in dw_mci_of_get_slot_quirks()
if CONFIG_OF is defined, thus there is no need to have a !CONFIG_OF
version of it. Fixes the following compile warning with !CONFIG_OF:

  CC [M]  drivers/mmc/host/dw_mmc.o
drivers/mmc/host/dw_mmc.c:2223:28: warning: ‘dw_mci_of_find_slot_node’ defined but not used [-Wunused-function]
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Checks EXT_CSD_PARTITION_SETTING_COMPLETED bit before
 computing enhanced user area offset and size, and
 adding mmc general purpose partitions. The two needs
 EXT_CSD_PARTITION_SETTING_COMPLETED bit be set to be
 valid (as described in JEDEC standard).
Warn user in case of misconfiguration.
Signed-off-by: NGrégory Soutadé <gsoutade@neotion.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Replace ext_csd "enhanced_area_en" attribute by
 "partition_setting_completed". It was used whether or
 not enhanced user area is defined and without checks of
 EXT_CSD_PARTITION_SETTING_COMPLETED bit.
Signed-off-by: NGrégory Soutadé <gsoutade@neotion.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Move code that manages user area and general purpose
 partitions into functions.
Signed-off-by: NGrégory Soutadé <gsoutade@neotion.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Commit 0dcaa249 improved error
handling of sdhci_add_host. However, "err_of_parse" and "err_cd_req"
should be placed after "pm_runtime_disable(&pdev->dev)".
Signed-off-by: NXiang Wang <wangx@marvell.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch renames sdio flag in vendor data to st_sdio, as this flag is
only used to enable ST specific sdio setup. This will also ensure that
the ST specfic setup is not done on other vendor like Qualcomm.

Originally the issue was detected while testing WLAN ath6kl on IFC6410
board with APQ8064 SOC.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch adds sdio enable mask in variant data, SOCs like ST have
special bits in datactrl register to enable sdio. Unconditionally setting
this bit in this driver breaks other SOCs like Qualcomm which maps this
bits to something else, so making this enable bit to come from variant
data solves the issue.

Originally the issue is detected while testing WLAN ath6kl on Qualcomm
APQ8064.
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Currently the MMCI driver will only handle GPIO descriptors
implicitly through the device tree probe glue in mmc_of_init(),
but devices instatiated other ways such as through board files
and passing descriptors using the GPIO descriptor table will
not be able to exploit descriptors.

Augment the driver to look for a GPIO descriptor if device
tree is not used for the device, and if that doesn't work,
fall back to platform data GPIO assignment using the old
API. The end goal is to get rid of the platform data integer
GPIO assingments from the kernel.

This enable the MMCI-embedding platforms to be converted to
GPIO descritor tables.

Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This switches the central MMC OF parser to use gpio descriptors
instead of grabbing GPIOs explicitly from the device tree.
This strips out an unecessary use of the integer-based GPIO
API that we want to get rid of, cuts down on code as the
gpio descriptor code will handle active low flags.
Acked-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This makes it possible to get the write protect (read only)
GPIO line from a GPIO descriptor. Written to exactly mirror
the card detect function.
Acked-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

When the slot GPIO driver gets the GPIO to be used for card
detect, it is now possible to specify a flag to have the line
set up as input. Get rid of the explicit setup call for input
and use the flag.

The extra argument works as there are transition varargs
macros in place in the <linux/gpio/consumer.h> header, in
the future we will make the flags argument compulsory.
Reviewed-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

It seems very unlikely that eMMC devices would hold a standard
partitiontable in one of it's boot areas. Therefore, let's prevent
them from being scanned.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Now, mmc framework uses multi_io_quirk
for I/O HW bug workaround.
MMC_CAP2_NO_MULTI_READ flag is no longer needed
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

sh_mobile_sdhi cares multiblock read bug.
remove MMC_CAP2_NO_MULTI_READ flag from board code
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

sh_mobile_sdhi cares multiblock read bug.
remove MMC_CAP2_NO_MULTI_READ flag from board code
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Now, sh_mobile_sdhi can use .multi_io_quirk callback
instead of MMC_CAP2_NO_MULTI_READ flags.
let's use it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Now, tmio_mmc can use .multi_io_quirk callback
instead of MMC_CAP2_NO_MULTI_READ flags.
let's use it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Now, omap_hsmmc can use .multi_io_quirk callback
instead of MMC_CAP2_NO_MULTI_READ flags.
let's use it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Due to HW issue, SDHCI host controller on Intel
Baytrail/Merrifield platforms can not use preset
register. So, disable preset registers for them by quirks.
Signed-off-by: NYunpeng Gao <yunpeng.gao@intel.com>
Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Historically, we have been using MMC_CAP* to handle host HW issues and
currently the block layer uses MMC_CAP2_NO_MULTI_READ flag for a multi
I/O HW bug workaround.

There are a few tweaks needed to make MMC_CAP2_NO_MULTI_READ suite all
situations. Therefore let's add an optional host ops callback to enable
host drivers to return the number of blocks it allows per request.

In a future patch and when host drivers have converted to the new
callback, MMC_CAP2_NO_MULTI_READ shall be removed.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Right now enable 1.2v IO voltage for SDHC is by using vqmmc.
Thus for the host which doesn't have vqmmc, or its vqmmc does
not support 1.2v, directly use MMC_CAP2_HS200 may cause HS200
failure.

So needs to check if vqmmc is able to support 1.2v. If it does
not support, disable 1.2v IO for HS200.
Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Even (e)MMC card can support 3.3v to 1.2v vccq in DDR, but not all
host controller can support this, like some of the SDHCI host
which connect to an eMMC device. Some of these host controller
still needs to use 1.8v vccq for supporting DDR mode.

So the sequence will be:
if (host and device can both support 1.2v IO)
	use 1.2v IO;
else if (host and device can both support 1.8v IO)
	use 1.8v IO;
so if host and device can only support 3.3v IO, this is the last choice.
Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: NYunpeng Gao <yunpeng.gao@intel.com>
Tested-by: NJean-Michel Hautbois <jhautbois@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add the clock prepare and unprepare call to the driver set_ios calls
phase. This will remove a warning once the PXA architecture is migrated
to the clock infrastructure.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Similar to sdhci-pci controller, also add probe_slot
and remove_slot method in the sdhci-acpi driver.
Signed-off-by: NYunpeng Gao <yunpeng.gao@intel.com>
Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Enable runtime pm support on Intel Merrifield platform.
Signed-off-by: NYunpeng Gao <yunpeng.gao@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

It is fully legal for a controller to start handling busy-end interrupt
before it has signaled that the command has completed. So make sure
we do things in the proper order, Or it results that command interrupt
is ignored so it can cause unexpected operations. This is founded at some
toshiba emmc with the bellow warning.

"mmc0: Got command interrupt 0x00000001 even though
no command operation was in progress."

This issue has been also reported by Youssef TRIKI:
It is not specific to Toshiba devices, and happens with eMMC devices
as well as SD card which support Auto-CMD12 rather than CMD23.

Also, similar patch is submitted by:
Gwendal Grignou <gwendal@chromium.org>

Changes since v1:
 Fixed conflict with the next of git.linaro.org/people/ulf.hansson/mmc.git
 and Tested if issue is fixed again.
Signed-off-by: NHankyung Yu <hankyung.yu@lge.com>
Signed-off-by: NChanho Min <chanho.min@lge.com>
Tested-by: NYoussef TRIKI <youssef.triki@st.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

sdhci_disable_irq_wakeups() is exported, but it is not called outside sdhci.c.

Make it static and do not export it, so that the following sparse warning is
fixed:

drivers/mmc/host/sdhci.c:2548:6: warning: symbol 'sdhci_disable_irq_wakeups' was not declared. Should it be static?
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The timeout_clk calculation code for SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK case
is common and could be moved into common sdhci_do_set_ios, then platform code
which is not using sdhci_set_clock does not need to write the same code again.
Signed-off-by: NDong Aisheng <b29396@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The timeout_clk calculation code in sdhci_add_host is meaningless for
SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK.
So only execute them with no SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK set.
Signed-off-by: NDong Aisheng <b29396@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The default sdhci driver write 0xE into timeout counter register to
set the maximum timeout. The value is not correct for uSDHC since the
max counter value for uSDHC is 0xF.
Instead of using common timeout code in sdhci, we implement esdhc_set_timeout
to handle the difference between eSDHC and uSDHC.

Currently we simply set the max timeout value as before.
But in the future, we probably may implement IMX specific timeout
setting algorithm and use suitable timeout for different CMDs.
Reviewed-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDong Aisheng <b29396@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Currently the common code assume 0xE is the maximum timeout counter
value and use it to write into the timeout counter register.
However, it's fairly possible that some other SoCs may have different
max timeout register value. That means 0xE may be incorrect and
becomes meaningless.

It's also possible that other platforms has different timeout
calculation algorithm. To be flexible, this patch provides a .set_timeout
hook for those platforms to set the timeout on their way if they need.
Reviewed-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDong Aisheng <b29396@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The default sdhci code use the 1 << 27 as the max timeout counter to
to calculate the max_busy_timeout, however it's not correct for uSDHC
since its the max counter is 1 << 28.
Implement esdhc_get_max_timeout_cout to handle it correctly.
Reviewed-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDong Aisheng <b29396@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Currently the max timeout count is hardcode to 1 << 27 for calcuate
the max_busy_timeout, however, for some platforms the max timeout
count may not be 1 << 27, e.g. i.MX uSDHC is 1 << 28.
Thus 1 << 27 is not correct for such platform.

It is also possible that other platforms may have different values.
To be flexible, we add a get_max_timeout_count hook to get the correct
maximum timeout value for these platforms.
Reviewed-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDong Aisheng <b29396@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

- r8a7792 (R-Car V2H)
  - r8a7793 (R-Car M2-N)
  - r8a7794 (R-Car E2)
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

It's possible that mmc_of_parse() could return errors (possibly in
some future version it might return -EPROBE_DEFER even).  Let's pass
those errors back.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

the implementation of CSR SDHCI controller is a modified version of
the one described in the 1.0 specification, and not a normal 3.0
controller.
and 8bit-width enable bit of CSR MMC hosts is 3, while stardard hosts
use bit 5.
this patch fixes the functionality of 8bit transfer in mmc controllers
and improve performance for mmc0 a lot.
Signed-off-by: NMinda Chen <Minda.Chen@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Reviewed-by: NRomain Izard <romain.izard.pro@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

For UHS cards we need the ability to switch voltages from 3.3V to
1.8V.  Add support to the dw_mmc driver to handle this.  Note that
dw_mmc needs a little bit of extra code since the interface needs a
special bit programmed to the CMD register while CMD11 is progressing.
This means adding a few extra states to the state machine to track.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NYuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch makes use of mmc_regulator_get_supply() to handle
the vmmc and vqmmc regulators.Also it moves the code handling
the these regulators to dw_mci_set_ios().It turned on the vmmc
and vqmmc during MMC_POWER_UP and MMC_POWER_ON,and turned off
during MMC_POWER_OFF.
Signed-off-by: NYuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

With one special SD card, below divide by zero error observed:
...
[    2.144300] divide error: 0000 [#1] PREEMPT SMP
[    2.148860] Modules linked in:
[    2.151898]
[    2.152685] Set up 4031 stolen pages starting at 0x0001f000, GTT offset 0K
[    2.157330] Set up 0 CI stolen pages starting at 0x00000000, GTT offset 131072K
[    2.167581] Pid: 5, comm: kworker/u:0 Not tainted 3.0.8-138216-g974a2aba #1
[    2.169506] [drm] PSB GTT mem manager ready, tt_start 4031, tt_size 28737 pages
[    2.169906] [drm] SGX core id = 0x00000000
[    2.169920] [drm] SGX core rev major = 0x00, minor = 0x00
[    2.169934] [drm] SGX core rev maintenance = 0x00, designer = 0x00
[    2.197370]  Intel Corporation Medfield/iCDKB
[    2.201716] EIP: 0060:[<c1697ca6>] EFLAGS: 00010246 CPU: 1
[    2.207198] EIP is at mmc_init_erase+0x76/0x150
[    2.211704] EAX: 00002000 EBX: dcd1b400 ECX: 00002000 EDX: 00000000
[    2.217957] ESI: 00000000 EDI: dcd5c800 EBP: dd867e84 ESP: dd867e7c
[    2.224214]  DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[    2.229605] Process kworker/u:0 (pid: 5, ti=dd866000 task=dd868000 task.ti=dd866000)
[    2.237325] Stack:
[    2.239322]  dcd1b400 00000000 dd867eb0 c16a06da c1ab7c44 dd995aa8 00000003 00000000
[    2.247054]  00000000 00000000 dcd5c800 00000000 dcd1b400 dd867ef8 c16a1012 c1698b00
[    2.254785]  00000029 00000001 c194eb80 dcd5c9ec dd867e00 c1239b00 00000000 00000000
[    2.262519] Call Trace:
[    2.264975]  [<c16a06da>] mmc_sd_setup_card+0x1da/0x4f0
[    2.270183]  [<c16a1012>] mmc_sd_init_card+0x192/0xc40
[    2.275304]  [<c1698b00>] ? __mmc_claim_host+0x160/0x160
[    2.280610]  [<c1239b00>] ? __schedule_bug+0x50/0x80
[    2.285556]  [<c16a1b89>] mmc_attach_sd+0xc9/0x230
[    2.290333]  [<c169b6ef>] mmc_rescan+0x25f/0x2c0
[    2.294943]  [<c1274223>] process_one_work+0x103/0x400
[    2.300065]  [<c12670fd>] ? mod_timer+0x1ad/0x3c0
[    2.304756]  [<c169b490>] ? mmc_suspend_host+0x1a0/0x1a0
[    2.310056]  [<c127502d>] worker_thread+0x12d/0x4a0
[    2.314921]  [<c18fcfbd>] ? preempt_schedule+0x2d/0x50
[    2.320047]  [<c1274f00[    2.323976] ---[ end trace 5398ec2720494438 ]---
...

So, seems this bad SD card does not set valid value in related SSR / CSD register fields.
And then the driver will set card->erase_size to 0.
Then it triggered this divided by zero error when calculate card->pref_erase.

Submit this patch to fix the issue.
Signed-off-by: NYunpeng Gao <yunpeng.gao@intel.com>
Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Declare ERASE capability so we can use filesystems with the discard
option and the fstrim tool.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>