commit 0d95521e (ath9k: use split rx buffers to get rid of order-1 skb
allocations) added in memory leak in error path.

sc->rx.frag should be cleared after the pskb_expand_head() call, or else
we jump to requeue_drop_frag and leak an skb.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Trond Wuellner <trond@chromium.org>
Cc: Grant Grundler <grundler@chromium.org>
Cc: Paul Stewart <pstew@chromium.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we have downlink traffic alone and the station is going thru
bgscan, the client is out of operating channel for around 1000ms which
is too long. The mac80211 decides when to switch back to oper channel
based on tx queue, bad latency and listen time. As the station does not
have tx traffic, the bgscan can easily affect downlink throughput. By
reducing the listen time, it helps the associated AP to retain the
downstream rate.

Cc: Paul Stewart <pstew@google.com>
Tested-by: NGary Morain <gmorain@google.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently the maximum noise floor limit is set as too high (-60dB). The
assumption of having a higher threshold limit is that it would help
de-sensitize the receiver (reduce phy errors) from continuous
interference. But when we have a bursty interference where there are
collisions and then free air time and if the receiver is desensitized too
much, it will miss the normal packets too. Lets make use of chips
specific min, nom and max limits always. This patch helps to improve the
connection stability in congested networks.

Cc: stable@vger.kernel.org
Cc: Paul Stewart <pstew@google.com>
Tested-by: NGary Morain <gmorain@google.com>
Signed-off-by: NMadhan Jaganathan <madhanj@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Makes them more readable and reduces code size
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Program tx gain through iniModesTxGain like on AR9287
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

use iniModesFastClock for 5 ghz fast clock specific settings, and
iniAdditional for clock/chip specific initval overrides
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Program the ah->ini_japan2484 INI values which were left out by accident
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These arrays are unused
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ATH9K_HW_CAP_AUTOSLEEP check is bogus, the rx status area needs to be
cleared on all non-EDMA PCI/AHB based chipsets anyway.
Limit the memset to the rx status area to improve performance.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver can just check the mask directly
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

By checking for NR_CPUS, the compiler can optimize out register access
serialization code on non-SMP kernels
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The default antenna (as programmed by the INI file) is always 0 anyway.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Automatically set the ah->htc_reset_init on init and after PHY disable.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

TXQ_FLAG_TXOKINT_ENABLE and TXQ_FLAG_TXERRINT_ENABLE are always set and
used together, and they share the same bitmask in enum ath9k_tx_queue_flags.
Simplify the code that tests for these flags.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mac80211 provides short preamble information and ERP protection
information on a per-BSS basis, which can be used. Remove flags
stored in the driver, which was incorrect since they were being used
in a global manner.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

SC_OP_TXAGGR and SC_OP_RXAGGR are not really needed.
The HT capabilities of the station and HW can be used instead.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The logic to determine whether to use FCC is a bit convoluted.
Use a small helper function to decide whether FCC is to be
used.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is not needed and will not be used anyway since
unsupported interfaces are not allowed to be created.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is no need to mask out SWBA/BMISS from the
interrupt mask in start().
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit 7504a3e1 ("ath6kl: add padding to firmware log records") accidentally
changed debug.c mode from 100644 to 100755. Revert that back to original.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath6kl/cfg80211.c:589: WARNING: max() should probably be
max_t(u16, vif->listen_intvl_t, ATH6KL_MAX_WOW_LISTEN_INTL)
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath6kl/sdio.c:875: CHECK: Alignment should match open parenthesis
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Recommended by checkpatch.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

My patch 24fc32b3 ("ath6kl: add ath6kl_bmi_write_hi32()") caused a regression
in ath6kl_upload_board_file() and the board_address variable was not
properly initialised in some cases:

ath6kl/init.c:1068:6: warning: ‘board_address’ may be used uninitialized
in this function

Most likely this broke ar6004 support but I can't test that right now.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The check for PS_WAIT_FOR_TX_ACK was inverted, the hardware should only go
to full sleep if no tx is pending.
Reported-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mactime was being overwritten by the function ath9k_rx_skb_preprocess. Fixed by
memsetting rx_status in ath_rx_tasklet.
Signed-off-by: NAshok Nagarajan <ashok@cozybit.com>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The proper place to configure bss info is at assoc notification. So that
ath9k continues to work if the supirous bssid notification will be
removed in future.

Cc: Johannes Berg <johannes@sipsolutions.net>
Reported-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

tested in AR9462 Rev:2, both hardware capability flag are set
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On systems with multiple NICs, it's nice to know which
one is producing warnings.  Here is an example of the
new ouput:

ath: wiphy0: Failed to stop TX DMA, queues=0x005!
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Flush MCI profiles only if MCI is being actually used.
This fixes a panic on driver unload when non-MCI devices
are being used and btcoex_enable is set.

BUG: unable to handle kernel NULL pointer dereference at           (null)
IP: [<ffffffffa06296d2>] ath_mci_flush_profile+0x12/0x100 [ath9k]
Call Trace:
[<ffffffffa061befe>] ath9k_stop_btcoex+0x5e/0x80 [ath9k]
[<ffffffffa061ed57>] ath9k_stop+0xb7/0x230 [ath9k]
[<ffffffffa0533f30>] ieee80211_stop_device+0x50/0x180 [mac80211]
[<ffffffffa051f0cf>] ieee80211_do_stop+0x2af/0x6a0 [mac80211]
[<ffffffffa051f4da>] ieee80211_stop+0x1a/0x20 [mac80211]
[<ffffffff81365d96>] __dev_close_many+0x86/0xe0
[<ffffffff81365ee0>] dev_close_many+0xa0/0x110
[<ffffffff81366038>] rollback_registered_many+0xe8/0x260
[<ffffffff813661cb>] unregister_netdevice_many+0x1b/0x80
[<ffffffffa051e950>] ieee80211_remove_interfaces+0xd0/0x110 [mac80211]
[<ffffffffa050c133>] ieee80211_unregister_hw+0x53/0x120 [mac80211]
[<ffffffffa061d5a4>] ath9k_deinit_device+0x44/0x70 [ath9k]
[<ffffffffa062c1d4>] ath_pci_remove+0x54/0xa0 [ath9k]
[<ffffffff81267c46>] pci_device_remove+0x46/0x110
[<ffffffff8131021c>] __device_release_driver+0x7c/0xe0
[<ffffffff81310960>] driver_detach+0xd0/0xe0
[<ffffffff81310078>] bus_remove_driver+0x88/0xe0
[<ffffffff81311122>] driver_unregister+0x62/0xa0
[<ffffffff81268004>] pci_unregister_driver+0x44/0xc0
[<ffffffffa062c8b5>] ath_pci_exit+0x15/0x20 [ath9k]
[<ffffffffa063205d>] ath9k_exit+0x15/0x31 [ath9k]
[<ffffffff810b92cc>] sys_delete_module+0x18c/0x270
[<ffffffff814373dd>] ? retint_swapgs+0x13/0x1b
[<ffffffff8124828e>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[<ffffffff81437de9>] system_call_fastpath+0x16/0x1b
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Portion of the commit id 080eec4f ("ath6kl: Clear the IE in firmware
if not set") was overwritten by mistake due to a merge
conflict. This patch fixes the code back to how it should be.

kvalo: more details to the commit log
Signed-off-by: NAarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

On A-MPDU frames, the hardware only reports valid signal strength data for
the last subframe. The driver also mangled rx_stats->rs_rssi using the
ATH_EP_RND macro in a way that may make sense for ANI, but definitely
not for reporting to mac80211.
This patch changes the code to calculate the signal strength from the rssi
directly instead of taking the average value, and flag everything but
the last subframe in an A-MPDU to tell mac80211 to ignore the signal strength
entirely, fixing signal strength fluctuation issues reported by various
users.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Process rx status directly instead of separating the completion test from
the actual rx status processing.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The way this is implemented (simply storing the last value) is absolutely
worthless for debugging anything, and the same information is also available
through the MAC sample feature, so there's no point in keeping this around.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

They're more expensive than some of the other debug options and only used
in very rare situations, so it sometimes makes sense to disable them while
leaving in debugfs support.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cold reset is more reliable for getting the hardware out of some specific
stuck states.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>