TLV based firmware ex. QCA6174, WCN3990 expects key cipher value
set to 9 while non-TLV firmware expects key cipher value set to 8
for enabling GCMP and GCMP-256 cipher suites.

To fix this problem, attach the key cipher suite values based on
wmi version.

Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: NAbhishek Ambure <aambure@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Hostapd uses CCMP, GCMP & GCMP-256 as 'wpa_pairwise' option to run WPA3.
In WCN3990 firmware cipher suite numbers 9 to 11 are for CCMP,
GCMP & GCMP-256.

To enable CCMP, GCMP & GCMP-256 cipher suites in WCN3990 firmware,
host sets 'n_cipher_suites = 11' while initializing hardware parameters.

Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: NAbhishek Ambure <aambure@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The series "[PATCH 0/2] mt76x0: initialize per-channel max_power" depends on
commit d04ca383 ("mt76x0u: fix suspend/resume"), so merge wireless-drivers
into wireless-drivers-next to get that.

ath.git patches for 5.1. Major changes:

ath10k

* change QMI interface to support the new (and backwards incompatible)
  interface from HL3.1 and used in recent HL2.0 branch firmware releases

ath

* add new country codes for US

We need to reset MCU and do other initializations on resume otherwise
MT7610U device will fail to initialize, what cause system hung due to
USB requests timeouts.

Patch fixes 4.19 -> 4.20 regression.

Cc: stable@vger.kernel.org # 4.20+
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds several country codes to the regd.h and regd_common.h
files in order to support devices like the Linksys EA6350v3, whose
country codes are not present in the original list. Without this patch,
all devices whose manufacturer programmed any of these code in their
EEPROM will not work.

The values for CTRY_UNITED_STATES2 and CTRY_UNITED_STATES3 were taken
from a post by Sven Eckelmann <sven.eckelmann@openmesh.com>:
<http://lists.infradead.org/pipermail/ath10k/2017-August/010014.html>
Signed-off-by: NOever Gonzalez <notengobattery@gmail.com>
Signed-off-by: NChristian Lamparter <chunkeey@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

as you are already in a tasklet, it is unnecessary to call
spin_lock_bh, because softirq already disable BH.
Signed-off-by: NZhiwei Jiang <qq282012236@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When calling debugfs functions, they can now return error values if
something went wrong.  If that happens, return a NULL as a *dentry to
the relay core instead of passing it an illegal pointer.

The relay core should be able to handle an illegal pointer, but add this
check to be safe.

Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Firmware sends the tx_duration for each in HTT_T2H_MSG_TYPE_PEER_STATS
msg. Fill the tx_duration sent by firmware in the tx stats information
per STA.

Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1,
           WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: NSurabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The firmware advertises the LDPC support information for HT in
HT capability info in the wmi service ready event. To provide
granularity, firmware now advertises WMI_HT_CAP_RX_LDPC and
WMI_HT_CAP_TX_LDPC separately. To support LDPC, host should
also check for WMI_HT_CAP_RX_LDPC and WMI_HT_CAP_TX_LDPC in HT
capabilities.

Add a condition to existing logic in host to know whether firmware
supports LDPC or not.

Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1,
           WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: NSurabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Reduce the transmit MSDU count for SDIO, to match with the descriptors
as used by the firmware. This also acts as a high watermark level for
transmit. Too many packets to the firmware results in transmit overflow
interrupt.

It only affect SDIO chip, it will not cause functionaly changes to
other hardware.

Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: NAlagu Sankar <alagusankar@silex-india.com>
Signed-off-by: NWen Gong <wgong@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When calling debugfs functions, they can now return error values if
something went wrong.  If that happens, return a NULL as a *dentry to
the relay core instead of passing it an illegal pointer.

The relay core should be able to handle an illegal pointer, but add this
check to be safe.

Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: ath10k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/wireless/ath/ath10k/snoc.c: In function 'ath10k_snoc_tx_pipe_cleanup':
drivers/net/wireless/ath/ath10k/snoc.c:681:22: warning:
 variable 'ar_snoc' set but not used [-Wunused-but-set-variable]
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Reviewed-by: NBrian Norris <briannorris@chromium.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

sdio_register_driver() doesn't do this for us, unlike (for example)
platform_driver_register(). This is important for helping track
module-to-device relationships.
Signed-off-by: NBrian Norris <briannorris@chromium.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The swap box flag of firmware is not set before htc ready, then it
will not set swap box flag in ath10k driver, and it will let swap
box setting not same between firmware and ath10k driver, then it
will trigger firmware assert failure.

Check the flag and set swap box after htc ready will fix the firmware
assert failure.

Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: NWen Gong <wgong@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The hw-restart crash inject mode is a special mode, where
there is no crash generated in the firmware, but instead
the driver restarts the firmware. In order to restart WCN3990
firmware, the driver needs to send qmi_wlan_disable message
followed by the qmi_wlan_enable message to the WCN3990 firmware.

Currently the qmi_wlan_disable message is not sent to
the WCN3990 firmware when hw-restart crash is injected,
which causes the firmware to crash when the driver sends
qmi_wlan_enable message during ath10k_restart.

Send qmi_wlan_disable to the WCN3990 firmware when the
hw-restart crash is injected via debugfs.

Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: NRakesh Pillai <pillair@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The management frames transmitted are dma mapped with
direction TO_DEVICE, but incorrectly mapped with
direction FROM_DEVICE during tx complete and error cases.

Fix the direction of dma during dma unmap of the
transmitted management frames.

Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1

Fixes: 38a1390e ("ath10k: dma unmap mgmt tx buffer if wmi cmd send fails")
Signed-off-by: NRakesh Pillai <pillair@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

WCN3990 sends tx completion of multiple management
frames bundled together in a single event, if the
host driver exposes the support to handle this
bundled tx completion event. This reduces the number
of WMI events which are sent to the host driver by
the target.

Set the BUNDLE_TX_COMPL flag in the host capability
flags when host sends the wmi init command, to indicate
the host capability to handle bundled tx completion for
management frames.

Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: NRakesh Pillai <pillair@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

WCN3990 supports sending tx completion for multiple
management frames bundled together in a single event.

Add support to handle the bundled tx completion
event for WCN3990.

Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: NRakesh Pillai <pillair@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

HOST capability interface data structures are updated
in HL3.1 fw version. Update the qmi host capability
members for compatibility across different firmware
versions.
Since this change breaks backward compatibility with
HL2.0 fw, HL2.0 fw upgrade to WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
or later version is required.

Testing:
        Tested on QCS404 platform(WCN3990 HW).
        Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1,
                   WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Merge tag 'iwlwifi-next-for-kalle-2019-02-04' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next

Third batch of iwlwifi patches intended for v5.1

* Work on the new debugging infrastructure continues;
* HE radiotap;
* Support for new FW version 44;
* A couple of new FW API changes;
* A bunch of fixes for static analyzer reported issues;
* General bugfixes;
* Other cleanups and small fixes;

The EMAC driver had a custom IBM_EMAC_RX_SKB_HEADROOM
Kconfig option that reserved additional skb headroom for RX.
This patch removes the option and migrates the code
to use napi_alloc_skb() and netdev_alloc_skb_ip_align()
in its place.
Signed-off-by: NChristian Lamparter <chunkeey@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Let's make genphy_c45_read_link behave the same as genphy_update_link
and set phydev->link in the function directly. This allows to simplify
the callers. In addition don't check further devices once we detect
that at least one device reports link as down.

v2:
- remove an unused variable
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current driver only enables Pdelay_Req and Pdelay_Resp when
HWTSTAMP_FILTER_PTP_V2_EVENT, HWTSTAMP_FILTER_PTP_V1_L4_EVENT or
HWTSTAMP_FILTER_PTP_V2_L4_EVENT is requested. This results in ptp sync on
slave mode to report 'received SYNC without timestamp' when using ptp4l.

Although the hardware can support Sync, Pdelay_Req and Pdelay_resp by
setting bit14 annd bits 17/16 to 01 this leaves Delay_Req timestamps out.

Fix this by enabling all event and general messages timestamps.
This includes SYNC, Follow_Up, Delay_Req, Delay_Resp, Pdelay_Req,
Pdelay_Resp and Pdelay_Resp_Follow_Up messages.
Signed-off-by: NIlias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: NJose Abreu <joabreu@synopsys.com>
Tested-by: NAlexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On one hand, the mv88e6xxx driver has a work queue called in loop
which will attempt register accesses after MDIO bus suspension, that
entirely freezes the platform during suspend.

On the other hand, the DSA core is not ready yet to support suspend to
RAM operation because so far there is no way to recover reliably the
switch configuration.

To avoid the kernel to freeze when suspending with a switch driven by
the mv88e6xxx driver, we choose to prevent the driver suspension and
in the same way, the whole platform.
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'for_net-next-5.1/rds-tos-v4' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux

Santosh Shilimkar says:

====================
rds: add tos support

RDS applications make use of tos to classify database traffic.
This feature has been used in shipping products from 2.6.32 based
kernels. Its tied with RDS v4.1 protocol version and the compatibility
gets negotiated as part of connections setup.

Patchset keeps full backward compatibility using existing connection
negotiation scheme. Currently the feature is exploited by RDMA
transport and for TCP transport the user tos values are mapped to
same default class (0).

For RDMA transports, RDMA CM service type API is used to
set up different SL(service lanes) and the IB fabric is configured
for tos mapping using Subnet Manager(SL to VL mappings).
Similarly for ROCE fabric, user priority is mapped with different
DSCP code points which are associated with different switch queues
in the fabric.

The original code was developed by Bang Nguyen in downstream kernel back in
2.6.32 kernel days and it has evolved significantly over period of time.

Thanks to Yanjun for doing testing with various combinations of host like
v3.1<->v4.1, v4.1.<->v3.1, v4.1 upstream to shipping v4.1 etc etc
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf-next 2019-02-07

The following pull-request contains BPF updates for your *net-next* tree.

The main changes are:

1) Add a riscv64 JIT for BPF, from Björn.

2) Implement BTF deduplication algorithm for libbpf which takes BTF type
   information containing duplicate per-compilation unit information and
   reduces it to an equivalent set of BTF types with no duplication and
   without loss of information, from Andrii.

3) Offloaded and native BPF XDP programs can coexist today, enable also
   offloaded and generic ones as well, from Jakub.

4) Expose various BTF related helper functions in libbpf as API which
   are in particular helpful for JITed programs, from Yonghong.

5) Fix the recently added JMP32 code emission in s390x JIT, from Heiko.

6) Fix BPF kselftests' tcp_{server,client}.py to be able to run inside
   a network namespace, also add a fix for libbpf to get libbpf_print()
   working, from Stanislav.

7) Fixes for bpftool documentation, from Prashant.

8) Type cleanup in BPF kselftests' test_maps.c to silence a gcc8 warning,
   from Breno.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Offload blackhole routes

Blackhole routes are routes that cause matching packets to be silently
dropped. This is in contrast to unreachable routes that generate an ICMP
host unreachable packet in response.

The driver currently programs both route types with a trap action and
lets the kernel drop matching packets. This is sub-optimal as packets
routed using a blackhole route can be directly dropped by the ASIC.

Patch #1 alters mlxsw to program blackhole routes with a discard action.

Patch #2 adds a matching test.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use a simple topology consisting of two hosts directly connected to a
router. Make sure IPv4/IPv6 ping works and then add blackhole routes.
Test that ping fails and that the routes are marked as offloaded. Use a
simple tc filter to test that packets were dropped by the ASIC and not
trapped to the CPU.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Create a new FIB entry type for blackhole routes and set it in case the
type of the notified route is 'RTN_BLACKHOLE'.

Program such routes with a discard action and mark them as offloaded
since the device is dropping the packets instead of the kernel.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: Introduce ndo_get_port_parent_id()

Based on discussion with Ido and feedback from Jakub there are clearly
two classes of users that implement SWITCHDEV_ATTR_ID_PORT_PARENT_ID:

- PF/VF drivers which typically only implement return the port's parent
  ID, yet have to implement switchdev_port_attr_get() just for that

- Ethernet switch drivers: mlxsw, ocelot, DSA, etc. which implement more
  attributes which we want to be able to eventually veto in the context
  of the caller, thus making them candidates for using a blocking notifier
  chain

Changes in v4:

- remove superfluous net/switchdev.h inclusions in a few files
- added Jiri's Acked-by where given
- removed err = -EOPNOTSUPP initializations
- changed according to Jiri's suggestion in net/ipv4/ipmr.c

Changes in v3:

- keep ethsw's switchdev_ops assignment
- remove inclusion of net/switchdev.h in netdevsim which is no longer
  necesary

Changes in v2:

- resolved build failures spotted by kbuild test robot
- added helpers functions into the core network device layer:
  dev_get_port_parent_id() and netdev_port_same_parent_id();
- added support for recursion to lower devices

Changes from RFC:

- introduce a ndo_get_port_parent_id() and convert all relevant drivers
  to use it

- get rid of SWITCHDEV_ATTR_ID_PORT_PARENT_ID

A subsequent set of patches will convert switchdev_port_attr_set() to
use a blocking notifier call, and still get rid of
switchdev_port_attr_get() altogether.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that we have a dedicated NDO for getting a port's parent ID, get rid
of SWITCHDEV_ATTR_ID_PORT_PARENT_ID and convert all callers to use the
NDO exclusively. This is a preliminary change to getting rid of
switchdev_ops eventually.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DSA implements SWITCHDEV_ATTR_ID_PORT_PARENT_ID and we want to get rid
of switchdev_ops eventually, ease that migration by implementing a
ndo_get_port_parent_id() function which returns what
switchdev_port_attr_get() would do.
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ethsw implements SWITCHDEV_ATTR_ID_PORT_PARENT_ID and we want to get rid
of switchdev_ops eventually, ease that migration by implementing a
ndo_get_port_parent_id() function which returns what
switchdev_port_attr_get() would do.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netdevsim only supports SWITCHDEV_ATTR_ID_PORT_PARENT_ID, which makes it a
great candidate to be converted to use the ndo_get_port_parent_id() NDO
instead of implementing switchdev_port_attr_get().
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mlxsw implements SWITCHDEV_ATTR_ID_PORT_PARENT_ID and we want to get rid
of switchdev_ops eventually, ease that migration by implementing a
ndo_get_port_parent_id() function which returns what
switchdev_port_attr_get() would do.
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NFP only supports SWITCHDEV_ATTR_ID_PORT_PARENT_ID, which makes it a
great candidate to be converted to use the ndo_get_port_parent_id() NDO
instead of implementing switchdev_port_attr_get().

Since NFP uses switchdev_port_same_parent_id() convert it to use
netdev_port_same_parent_id().
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ocelot only supports SWITCHDEV_ATTR_ID_PORT_PARENT_ID as a valid
switchdev attribute getter, convert it to use ndo_get_port_parent_id()
and get rid of the switchdev_ops::switchdev_port_attr_get altogether.
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mlxsw implements SWITCHDEV_ATTR_ID_PORT_PARENT_ID and we want to get rid
of switchdev_ops eventually, ease that migration by implementing a
ndo_get_port_parent_id() function which returns what
switchdev_port_attr_get() would do.
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mlx5e only supports SWITCHDEV_ATTR_ID_PORT_PARENT_ID, which makes it a
great candidate to be converted to use the ndo_get_port_parent_id() NDO
instead of implementing switchdev_port_attr_get().

Since mlx5e makes use of switchdev_port_parent_id() convert it to use
netdev_port_same_parent_id().
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>