AN serves multiple purposes.  For ATAPI, it's used for media change
notification.  For PMP, for downstream PHY status change notification.
Implement sata_async_notification() which demultiplexes AN.

To avoid unnecessary port events, ATAPI AN is not enabled if PMP is
attached but SNTF is not available.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Kriten Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Some pseudo devices fail PM commands unnecessarily aborting system
suspend.  Implement ATA_HORKAGE_SKIP_PM which makes libata skip PM
commands for these devices.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

If PMP itself becomes inaccessible while trying to link a downstream
link, spending time to recover the downstream link doesn't make any
sense.  Make EH skip retry and fail fast if -ERESTART is received.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Implement ATA_LFLAG_DISABLED.  The flag indicates the link is disabled
due to EH recovery failure.  While a link is disabled, no EH action is
taken on the link and suspend/resume become noop too.

This will be used by PMP links to manage failed links.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Some PMP links are connected to internal pseudo devices which may come
and go depending on situation.  There's no reason to try hard to
recover them.  ATA_LFLAG_NO_RETRY tells EH to not retry if the device
attached to the link fails.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Some links on some PMPs locks up on SRST and/or report incorrect
device signature.  Implement ATA_LFLAG_NO_SRST, ASSUME_ATA and
ASSUME_SEMB to handle these quirky links.  NO_SRST makes EH avoid
SRST.  ASSUME_ATA and SEMB forces class code to ATA and SEMB_UNSUP
respectively.  Note that SEMB isn't currently supported yet so the
_UNSUP variant is used.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Implement ap->nr_active_links (the number of links with active qcs),
ap->excl_link (pointer to link which can be used by ->qc_defer and is
cleared when a qc with ATA_QCFLAG_CLEAR_EXCL completes), and
ata_link_active().

These can be used by ->qc_defer() to implement proper command
exclusion.  This set of helpers seem enough for both sil24 (ATAPI
exclusion needed) and cmd-switching PMP.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Controllers which support PMP have various restrictions on which
combinations of commands are allowed to what number of devices
concurrently.  This patch implements ops->qc_defer() which determines
whether a qc can be issued at the moment or should be deferred.

If the function returns ATA_DEFER_LINK, the qc will be deferred until
a qc completes on the link.  If ATA_DEFER_PORT, until a qc completes
on any link.  The defer conditions are advisory and in general
ATA_DEFER_LINK can be considered as lower priority deferring than
ATA_DEFER_PORT.

ops->qc_defer() replaces fixed ata_scmd_need_defer().  For standard
NCQ/non-NCQ exclusion, ata_std_qc_defer() is implemented.  ahci and
sata_sil24 are converted to use ata_std_qc_defer().

ops->qc_defer() is heavier than the original mechanism because full qc
is prepped before determining to defer it, but various information is
needed to determine defer conditinos and fully translating a qc is the
only way to supply such information in generic manner.

IMHO, this shouldn't cause any noticeable performance issues as

* for most cases deferring occurs rarely (except for NCQ-aware
  cmd-switching PMP)
* translation itself isn't that expensive
* once deferred the command won't be repeated until another command
  completes which usually is a very long time cpu-wise.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make a number of functions from libata-core.c and libata-eh.c global
to libata (drivers/ata/libata.h).  These will be used by PMP.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Consider newly found class code while revalidating.  PMP resetting
always results in valid class code and issuing PMP commands to
ATA/ATAPI device isn't very attractive.  Add @new_class to
ata_dev_revalidate() and check class code for revalidation.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Update AN support in preparation of PMP support.

* s/ata_id_has_AN/ata_id_has_atapi_AN/
* add AN enabled reporting during configuration
* add err_mask to AN configuration failure reporting
* update LOCKING comment for ata_scsi_media_change_notify()
* check whether ATA dev is attached to SCSI dev ata_scsi_media_change_notify()
* set ATA_FLAG_AN in ahci and sata_sil24
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Kriten Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NJeff Garzik <jeff@garzik.org>

Clear ARRE, we don't do auto-reallocation on reads, just on writes.

Also, hardcode the size of the array using RW_RECOVERY_MPAGE_LEN,
following the style of the surrounding code.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* SAT specifies that FORMAT UNIT should be translated into a series
  of READ and WRITE commands that zero the ATA device.  That is far too
  cumbersome to bother with.

  Since we don't actually format the device, the old behavior of
  always returning success was inaccurate.  Change FORMAT UNIT from
  returning success immediately (old behavior) to always returning
  an error (new behavior).

* Add some comments around SYNCHRONIZE CACHE

* Shuffle scsi command code around a bit, so that things are close
  to alphabetic order.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

A few pedantic apps care about missing or lame "mandatory" SCSI
commands, so

REQUEST SENSE -- as we autosense, R.S. just returns zeroes

SEND DIAGNOSTIC -- our default (no-op) self-test succeeds, all
		   other requests for testing fail.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NJason Gaston <jason.d.gaston@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Certain device which reports diagnostic failure also reports invalid
device signature.  Assume ATA_DEV_ATA on diagnostic failure if reset
indicates device presence.

This is fix for bugzilla bug 8784.

  http://bugzilla.kernel.org/show_bug.cgi?id=8784Signed-off-by: NTejun Heo <htejun@gmail.com>
Acked-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Edward Amsden <amsden_linux@earthlink.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make ata_dev_try_classify() take a pointer to ata_device instead of
ata_port/port_number combination for consistency and add @present
argument.  @present indicates whether the device seems present during
reset.  It's the result of TF access during softreset and link
onlineness during hardreset.  @present will be used to improve
diagnostic failure handling.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Reimplement port_map handling such that

1. Non-zero PORTS_IMPL value is always examined and used if consistent
   with cap.n_ports.

2. When PI and cat.n_ports are inconsistent, honor cap.n_ports and
   force port_map to be ((1 << cap.n_ports) - 1).

3. There were two separate places dealing with port_map.  Unify them
   to one.

As all newer ahci chips seem to get PI correct and older ones usually
have zero PI.  Controllers with holes in PI are very unlikely to screw
up PI, so #2 makes more sense than following inconsistent PI.

Without this change, not setting ATA_FLAG_HONOR_PI when it's needed
results in weird detection failure.  This changed logic should be able
to handle all known cases correctly automatically.

Verified on ICH6 (reports 0 PI), ICH8 (with holes in port_map), ICH9,
JMB360 and JMB363.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch reimplement ata_hpa_resize() such that...

* All HPA related decisions are made inside ata_hpa_resize() proper.
  ata_hpa_resize() returns 0 if configuration can proceed, -errno if
  device needs to be reset and reconfigured.

* All errors are handled properly.  If HPA unlocking isn't requested,
  HPA handling is disabled automatically to avoid unnecessary device
  detection failure.

* Messages are trimmed.  HPA detection message is printed only during
  initial configuration.  HPA unlocked message is printed only during
  initial configuration or unlocking results in different size.

* Instead of using sectors returned in TF of SET_MAX, re-read IDENTIFY
  data as that's the value the device is going to use.

* It's called early during ata_dev_configure() as IDENTIFY data might
  change after resizing.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Merge ata_read_native_max_addres_ext() into ata_read_native_max_address()
and combine ata_set_native_max_address_ext() and
ata_set_native_max_address() into ata_set_max_sectors().

* reduce duplicate code
* return 0 or -errno depending on error conditions
* report if command fails
* use ATA_LBA instead of 0x40

This is in preparation of ata_hpa_resize() update.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Move ata_id_n_sectors() upward right below ata_id_c_string().  This is
to accomodate later changes.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch removes some incorrect formatting spaces and replaces them with tabs.
Signed-off-by: NJason Gaston <jason.d.gaston@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

  simple search-and-replace of direct scsi_cmnd access to
  use the data buffer accessors.
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

     This is a minimal patch needed to remove use of !use_sg
     but it is not a complete clean up of the !use_sg paths.
     Libata-core still has the qc->flags & ATA_QCFLAG_SG
     and !qc->n_elem code paths. Perhaps an ata maintainer
     would have a go at it.

     - TODO: further cleanup of qc->flags & ATA_QCFLAG_SG
       and !qc->n_elem code paths in libata-core
     - TODO: Use scsi_dma_{map,unmap} where applicable.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Some iomap functions were still using readl/writel and friends which
happens to work on most platforms but is not correct.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Support the use of '*' in model_num and model_rev entries
in ata_device_blacklist[].

Based largely on David Milburn's "libata-core: support wildcard matching
in ata_blacklist_entry" patch.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Use a form of array init that is less fragile, less sensitive to trivial
typos and ordering mismatches.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Updated and simplified driver. Use only register transfer timing for both
data and register transfers. This gives poorer performance in PIO1 and 2,
but should not be a problem in PIO3 and 4, correct me if I'm wrong :)

The driver works very we'll but I still wonder about the interrupts. I have
an interrupt line, that works nicely when POLLING flag is not set. The
problem is the number of interrupts that eat away my CPU cycles.

When using the POLLING flag there seem to be some interrupts that dosen't get
cleared. Furthermore the device dosen't drive INTRQ high, it stays at 2.5 volts
and generates a lot of interrupts due to ripple / noise. What to do?
Signed-off-by: NKristoffer Nyborg Gregertsen <kngregertsen@norway.atmel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix all issues pointed out in Jeff's email.
Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

EH is sometimes repeated without any error or action.  For example,
this happens when probing IDENTIFY fails because of a phantom device.
In these cases, all the repeated EH does is making sure there is no
unhandled error or pending action and return.  This repeation is
necessary to avoid losing any event which occurred while EH was in
progress.

Unfortunately, this dry run causes annonying "EH pending after
completion" message.  This patch moves the repeat reporting into
ata_eh_report() such that it's more compact and skipped on dry runs.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Mikael Pettersson <mikep@it.uu.se>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Currently, port configuration reporting has the following problems.

* iomapped address is reported instead of raw address
* report contains irrelevant fields or lacks necessary fields for
  non-SFF controllers.
* host->irq/irq2 are there just for reporting and hacky.

This patch implements and uses ata_port_desc() and
ata_port_pbar_desc().  ata_port_desc() is almost identical to
ata_ehi_push_desc() except that it takes @ap instead of @ehi, has no
locking requirement, can only be used during host initialization and "
" is used as separator instead of ", ".  ata_port_pbar_desc() is a
helper to ease reporting of a PCI BAR or an offsetted address into it.

LLD pushes whatever description it wants using the above two
functions.  The accumulated description is printed on host
registration after "[S/P]ATA max MAX_XFERMODE ".

SFF init helpers and ata_host_activate() automatically add
descriptions for addresses and irq respectively, so only LLDs which
isn't standard SFF need to add custom descriptions.  In many cases,
such controllers need to report different things anyway.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Minor cleanup to remove the unneeded rmb()s per Jeff's advice. Also removed the
pll_clock < 0 check since pll_clock now guaranteed to be >= 0 after Mikael's patch.
Signed-off-by: NAlbert Lee <albertcc@tw.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

If we have a PATA cable with a SATA drive on it then we've found a
bridge and we can flip the cable type. This fixes some cable detect
problems with SATA bridges on chipsets and misdetected cable types.

In theory cable detection and mode limiting is needed if you put a
SATA/PATA bridge on a 40 wire cable, but I see no way to deal with
that other than to point out its not a good idea anyway.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This avoids allocating DMA buffers if not needed but at the moment is
mostly just a neatness item.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

It was always set to ata_port_disable().  Removed the hook, and replaced
the very few ap->ops->port_disable() callsites with direct calls to
ata_port_disable().
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Testing this on the VIA boards fixes several problems with otherwise
undetectable SATA bridge chips
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

We can make use of this on the pata_amd driver as many Nvidia devices
don't have reliable cable detect.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>